Outdoor GreatRoom Company The Cove User manual

The Cove Fire Pit
Installation Instructions for CV-1242

2
Contents
Required Tools………………………………….........2
Included with your Fire Pit………………………..3
Assembly Instructions……………………………….4
Sparker Box Installation…………………………….4
Gas Connections……………………………………….5
Burner installation………………………………..….6
Glass Installation………………………………………7
Required Tools
FOUR people are required for this installation.
2 Open Ended Wrenches
To secure gas connections.
Leather Gloves
To protect hands from rough edges found on fire pit
during installation.
One AAA Battery (not included)
Required for electric spark igniter installation.
Utility Knife
To cut and remove packaging.
Power Drill
To remove support board from crate.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CF-1242 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42468 REV D 01-13-20

3
Included With Your Fire Pit
CV-1242-BASE with Control Panel
Burner Riser (P/N: 10298)
CFP1242 Crystal Fire Burner Kit

4
Assembly Instructions
1. Remove Cove-1242-Base from Packaging crate
Four People are required to lift base out of packaging
and place into final location.
2. Sparker Box Installation
Remove sparker cap and hex nut. Insert AAA battery
(not included) with + end out.
Install sparker into control panel as shown below,
secure using hex nut and replace sparker cap.
Depress sparker button to ensure your sparker is
working properly. You should hear the spark behind the
sparker box.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

5
3. Gas Connections
See Crystal Fire Plus instructions for burner
installation.
oAll gas connections were completed at the
factory.
Check all connections for leaks. If needed, tighten
connection with 2 wrenches and
re-check for leaks.
Attach burner valve to control panel with provided
screws as shown below. Ensure sparker box is installed
before this step.
4. Thermocouple Installation
• Refer to Crystal Fire Plus instruction manual for detailed
attachment of thermocouple.
• Attach thermocouple to burner valve as shown below.

6
5. Connect Ground wire and Electrode wire from
burner to sparker box.
Plug both BLACK wires hanging from the burner
into the back of the sparker box. If an orange wire
is present, do not use it. The orange wire is for
automatic ignition system add-on only.
Test system by pushing the button on the igniter.
Consult the troubleshooting section of the Crystal
Fire Plus Burner Owner’s Manual, if the spark is
weak, intermittent, or not present.
6. Drop Burner into base.
•Place burner riser (P/N: 10298) into recessed opening in base.
•Place burner on top of riser.

7
7. Install Fire Media
Scatter all included glass beads, lava rock, or other
approved fire media evenly across entire burner
surface.
DO NOT OPERATE CRYSTAL FIRE PLUS BURNER
WITHOUT INCLUDED GLASS BEADS OR OTHER
APPROVED FIRE MEDIA
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CF-1242 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.

8
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
https://www.outdoorrooms.com/product-registration
to register your product.
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]