Outdoor GreatRoom Company VNG-1224BRN User manual

The Vintage Fire Pit Table
Installation Instructions for Vintage Fire Pit Table
VNG-1224BRN

2

3
Contents
Required Tools…………………………….…..2
Placing and assembling the Table.………3
Gas Connection………………………….…….4
Igniter Installation…………….……………...6
Locating Propane tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Leather Gloves
To protect hands from rough edges
found on coffee table during
installation.
One AAA battery (not Included)
Required for electric spark igniter
installation
Two people are required for this
installatio
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to burner installation,
including safety information, proper tightening of connections with
two wrenches, and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
Contents
Required Tools……………………………………………….3
Included with your Fire Pit…………………………..…4
Assembly Instructions…………………………………….5
Gas Connections………………………………….………...6
Igniter Installation………………………………………….8
Position Your Tank (If Applicable)……………………9
Glass Installation……………………………………..……..9
Operating Instructions…………………………………..10
Required Tools
Two people are required for this installation
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges found on fire pit during
installation
One AAA Battery (not included)
Required for electric spark igniter installation
Utility Knife
To cut and remove packaging
Power Drill with phillips head bit
To secure tile top to base
42482 REV A 9.27.17

4
Included with your Fire Pit
CF-1224 Burner Kit
Tile Top attachment brackets (4)
Self-piercing sheet metal screws (8)
Door
Base
Top

5
Assembly Instructions
1. Open packaging and remove the access door before
removing the fire pit base from the box.
2. Set the base in the desired location and set top onto
base. Replace access door.
3. Install 4 tile top attachment brackets in the locations
shown below, using the cordless drill to drive the 8
self-piercing sheet metal screws.

6
Gas Connections
1. Reach inside the burner cut-out and attach natural gas supply
line using a 3/8” flare fitting, or attach the included black
rubber propane hose and regulator to the bottom fitting of the
control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information).
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Propane input
Natural gas input
or
Natural gas supply line
as specified by local
building codes
Gas Connections
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.

7
4. Set the burner into the fire pit table exactly as
shown.
5. Attach flex line from the burner to the gas valve as
shown.
Electrode
Access Door
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH

8
Igniter Installation
1. Make sure the valve is in the OFF
position before beginning.
2. Install sparker as shown, using an
AAA battery (not included).
Sparker will not operate correctly without an ignition
and ground wire attached.
3. Plug both BLACK wires hanging from the burner into the
back of the sparker box.
4. Test system by pushing the button on the igniter.
Consult the troubleshooting section if spark is weak,
intermittent, or not present.
After installing igniter and making gas connections,
verify that they are tight and that no leaks are present
using a solution of soapy water or a commercially available
leak-check solution.

9
Position Your Tank (If Applicable)
1. Remove door, connect the propane hose/regulator to the
propane tank and hand-tighten (DO NOT USE A WRENCH) and
slide the propane tank into place.
2. With tank inside base, ensure that no hoses, wires, or anything
else is kinked or touching the burner pan.
Glass Installation
1. Scatter all the included glass beads evenly
onto burner surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT
INCLUDED GLASS BEADS
DO NOT OPERATE CRYSTAL FIRE BURNER WITH
BURNER COVER IN PLACE

10
Operating Instructions
Before operating your fire pit, ensure all gas connections are
properly tightened and thoroughly leak checked. Refer to the
Crystal Fire Manual for information on proper leak checking and
other critical safety information.
With the control valve on the fire pit in the OFF position,
open the valve on the propane tank or natural gas
supply.
Make sure there are no gas leaks at the regulator or
inlet side of the key valve. If leak is detected,
immediately shut off the propane tank and wait 5
minutes to allow gas to dissipate. Fix any leaks before
proceeding.
Press the sparker button and hold, look and listen for
spark between electrode and grounding rod.
While depressing the sparker, press in and turn counter-
clockwise to open the valve.
If burner does not light after 10 seconds, close the valve
and wait 5 minutes to allow gas to dissipate before
attempting ignition again.
Refer to the Crystal Fire Manual included with your burner for
more detailed information on operation, maintenance, and safety
of your burner.
Always make sure all gas connections are properly
tightened and checked for leaks before operation.
3. Turn Valve to ON
2. Look/listen for spark
1. Depress sparker

11
WARNING
After consulting the manual and following instructions,
remember: before operating, all gas connections must be fully
checked for leaks
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form/
to register your product.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to burner installation,
including safety information, proper tightening of connections with
two wrenches, and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.

12
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]