Outdoor GreatRoom Company Denali DENBR-1242 User manual

Installation Instructions for Denali Fire Pit Table
DENBR-1242
Denali Fire Table
outdoorrooms.com

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER
WITHOUT CONSULTING THE CRYSTAL FIRE®PLUS
OWNER’S MANUAL.
CONTENTS
1. About Your Fire Table 2
a. Required Tools
outdoorrooms.com42510 REV B 06-16-20
!!
1
b. Included With Your Fire Pit
2. Assembly Instructions
a. Unpacking
b. CF-SPARKER and Control Valve Assembly
3. Setting Up Your Burner
a. Gas Connections
b. Burner Installation
c. CF-SPARKER Verication
d. Propane Tank Installation
4. Miscellaneous
a. Fire Media Installation
b. Glass Cover Installation
5. Operating Instructions
6. Warnings
3
4
7
9
10
c. Burner Cover Storage
d. Bottle Opener Attachment

outdoorrooms.com 2
• Utility Knife -
To cut and remove packaging
• 2 Open Ended Wrenches-
To secure gas connections
•Phillips Screw Driver (Do not use a drill to assemble)-
For assembly and attachment of bottle opener
• One AAA Battery (Not Included)-
Required for electric spark igniter installation
1.
Control Valve, Knob and
CF-SPARKER
(1)
ABOUT YOUR FIRE TABLE
Burner Cover
(1)
Fully Assembled Denali Fire
Table with CFP1242 Burner
(1)
A. REQUIRED TOOLS
B. INCLUDED WITH YOUR FIRE PIT
Bags of Glass Beads(3)
Bottle Opener Kit
(1)
CFP1242 Burner and Accessories
(1)

outdoorrooms.com 3
ASSEMBLY INSTRUCTIONS
•Do not discard any packaging until assembly is complete and unit is tested.
•Keep all included manuals in a safe place for future reference.
•Two people are recommended to remove table from packaging.
•Place table in desired location.
Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base.
2.
!!
A. UNPACKING
B. CF-SPARKER AND CONTROL VALVE
CONTROL PANEL
WARNING
• Control valve and sparker comes fully
assembled in table. Image 2.1
•Remove CF-SPARKER cap and hex nut.
Insert AAA battery (not included)
with + end out. Image 2.2
Image 2.1 Image 2.2

outdoorrooms.com 4
SETTING UP YOUR BURNER
ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before
beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
3.
!
!
Image 3.1
WARNING
Ensure valve is in the OFF position before making any gas connections.
!!
A. GAS CONNECTIONS
•For hard piped installations. Connect
the gas supply line (not included) to
the 3/8” male are tting on the valve.
USE TWO WRENCHES TO ENSURE A
GAS TIGHT CONNECTION.
•Run gas pipe up through the opening
in the bottom on the base. Image 3.1
•See Crystal Fire®Plus instructions for burner installation.
• All gas connections were completed at the factory.
• Check all connections for leaks. If needed, tighten connection with 2 wrenches
and re-check for leaks.
• Attach included control valve knob to control valve stem.

outdoorrooms.com 5
IMPORTANT
B. BURNER INSTALLATION
Please consult your Crystal Fire Plus® instruction manual for detailed instruc-
tions and important information related to the burner installation including:
lighting and operating instructions, safety information, and proper tightening
of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE®PLUS OWNER’S MANUAL.
• Burner is comes fully installed within re table. Refer to page 4 about leak
checks and retightening connections.
ATTENTION
TIGHTEN ALL CONNECTIONS
SECURELY WITH TWO WRENCHES
!
!!
!
C. CF-SPARKER VERIFICATION
• Test system by pushing the button on
the igniter. Consult the troubleshooting
section of the Crystal Fire® Plus owner’s
manual if the spark is weak, intermittent
or not present. Image 3.2
ATTENTION
Refer to the Crystal Fire manual included with your burner for more
detailed information on operation, maintenance, and safety of your burner.
!!
Image 3.2

outdoorrooms.com 6
• Lift door up and slide back into
table. Door will slide along metal
glides. Image 3.3
• Pull out tank tray. Image 3.3
• With the propane tank valve
and re pit valve o, attach the
propane regulator to the propane
tank. Image 3.4
• Place tank in tank tray.
•Slide tank drawer in. Ensure no
hoses or wires are contacting the
bottom of the burner. Image 3.4
• To replace access door, pull door
outward and bring back down
into resting position.
ATTENTION
Over time the bearings in the door glides may require re-greasing. Any
spray lubricant, such as WD-40, may be used to lubricate drawer glides.
Perform annually or on an as needed basis to maintain smooth operation.
! !
D. PROPANE TANK INSTALLATION
HAND TIGHTEN, DO NOT USE A WRENCH FOR THIS CONNECTION.
!
!ATTENTION
PROPANE REGULATOR
Image 3.3
Image 3.4

outdoorrooms.com 7
4. MISCELLANEOUS
A. FIRE MEDIA INSTALLATION
WARNING
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS
BEADS OR OTHER APPROVED FIRE MEDIA.
!!
•Scatter all included glass beads,
lava rock, or other approved re
media evenly across entire burner
surface. Image 4.1
B. BURNER COVER INSTALLATION
WARNING
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITH BURNER COVER IN PLACE.
!
!
•Fully shut o gas supply to table
and turn control valve knob to OFF
position. Wait for burner to become
cool before placing cover. Image 4.2
• Carefully place the cover on top of
the burner. Image 4.3
•Remove burner cover before
attempting ignition.
THE OUTDOOR
GREATROOM
COMPANY
Image 4.2
Image 4.1
Image 4.3

outdoorrooms.com 8
C. BURNER COVER STORAGE
ATTENTION
Use caution when removing and placing the
burner cover as to not chip or damage the edge.
!!
When not in use, Burner cover can be
conveniently stored on side of table
•Locate cover holders on lower base.
Image 4.4. Flip cover holders down.
Place burner cover onto holders.
• Rotate securement downward, over
cover, to lock cover in place.
• To remove cover, rotate securement
pins upward, lift cover o holders and
place back into burner opening. Flip
cover holders back up.
D. BOTTLE OPENER ATTACHMENT
Bottle opener can be placed on side of table top trim in a location of your
choosing. For best results, and to eliminate any splitting of wood, bottle
opener should be centered on trim and at least 3 inches from edge.
Image 4.5 gives an example of bottle opener placment. Pre-drill holes for
screws before attaching bottle opener.
COVER HOLDER
COVER
Image 4.5
Image 4.4
COVER SECUREMENT PIN

outdoorrooms.com 9
OPERATING INSTRUCTIONS
IMPORTANT
Before operating your DENBR-1242, ensure all gas connections are
properly tightened and thoroughly leak checked. Refer to the Crystal Fire®
Plus manual for information on proper leak checking and other critical
safety information.
5.
!!
!!
FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a re or explosion may result causing
property damage, personal injury, or loss of life.
Verify control valve is in OFF position. If operating on a self-contained propane
cylinder, ensure cylinder valve is CLOSED. If operating on a hard-piped system,
ensure main gas supply shut-o valve and all other valves in gas system are
OPEN.
If operating on a self-contained propane cylinder, slowly open cylinder valve.
Press and hold sparker button. Verify an audible and visible spark is present
within the ignition wind guard.
Gently press and turn control knob to LOW/IGNITION position. Fully depress
control knob and hold for 3-5 seconds. Burner should ignite and continue to
operate when control knob is released.
If burner does not light or remain lit after 20 seconds of attempting ignition, turn
control valve to OFF position and wait 5 minutes to allow gas to dissipate before
attempting ignition again. DO NOT ATTEMPT TO LIGHT BURNER IF YOU SMELL
GAS.
With burner lit and operating, the ame height can be adjusted between LOW
and HIGH at any time.
WARNING
OFF
LOW/
IGNITION
HIGH
PUSH AND HOLD
TO IGNITE
DEPRESS SPARKER
BUTTON
SEE DETAIL B
LOOK FOR SPARK
HERE
OFF
LOW/
IGNITION
HIGH
PRESS AND HOLD
SPARKER BUTTON
ROTATE COUNTER-CLOCKWISE
TO LOW AND SLOWLY DEPRESS
HOLD KNOB IN FOR 3-5 SECONDS