Outdoor GreatRoom Company Caden User manual

Installation Instructions for Caden Fire Pit Table
CAD-1224
Caden Fire Table
outdoorrooms.com

IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
CONTENTS
1. About Your Fire Table 2
a. Required Tools
outdoorrooms.com42506 REV A 03-12-19
!!
1
b. Included With Your Fire Pit
2. Assembly Instructions
a. Unpacking
b. Leg Assembly
c. Top Assembly
e. Side Assembly
d. CF-SPARKER and Control Valve Assembly
f. Bottom Component Assembly
3. Setting Up Your Burner
a. Gas Connections
b. Burner Installation
c. Electrode Installation
d. Propane Tank Installation
4. Miscellaneous
a. Fire Media Installation
b. Glass Cover Installation
5. Operating Instructions
6. Warnings
3
8
11
12
13

outdoorrooms.com 2
Refer to Crystal Fire manual for items included with Crystal Fire burners
• Utility Knife -
To cut and remove packaging
• 2 Open Ended Wrenches -
To secure gas connections
•Phillips Screw Driver (Do not use a drill to assemble) -
For assembly
• One AAA Battery (Not Included)-
Required for electric spark igniter installation
A. REQUIRED TOOLS
B. INCLUDED WITH FIRE PIT
1.
Table Top
(1)
Screw
(26)
Side Panel
(1)
Control Panel
(1)
End Panel
(1)
Legs
(4)
Door Frame
(1)
Door
(1)
Tank Tray
(1)
Control Valve and Knob
(1)
CF-1224 Burner and Accessories
(1)
Magnet and Screws
(1)
ABOUT YOUR FIRE TABLE
Leveling Feet
(4)

outdoorrooms.com 3
ASSEMBLY INSTRUCTIONS
UNPACKING
Do not discard any packaging until assembly is complete and unit is
tested. Keep all included manuals in a safe place for future reference.
It is recommended to keep top in box on a smooth at surface. This
protects the top from scratches and marks during assembly.
WARNING
Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base.
Do not remove protective cardboard packaging
until you have placed the re pit in
its desired location.
LEG ASSEMBLY
2.
1. Screw leveling feet onto legs. (4X)
!!
LEG
LEVELING FOOT

outdoorrooms.com 4
2. Screw legs onto end panel as shown below.
Apply foam gasket to top of panel and legs.
3. Screw legs onto door frame as shown below. Screw magnet
onto door frame.
Apply foam gasket to top of door frame and legs.
LEG
END PANEL
LEG
DOOR FRAME
MAGNET
FOAM THIS SIDE
FOAM THIS SIDE
SEE DETAIL A

outdoorrooms.com 5
TOP ASSEMBLY
4. Screw panel assemblies in steps 2 and 3 onto the top as shown be-
low. Loosely tighten screws, nal tightening of all screws after com-
pleting step 6 of assembly.
DOOR FRAME ASSEMBLY
END PANEL ASSEMBLY
TOP

outdoorrooms.com 6
CF-SPARKER
6. Apply foam to top side of panel.
Screw control panel onto side of base. Place side so that the
control panel is opposite the door frame. Repeat this step for
opposite side panel as shown below.
SIDE ASSEMBLY
CF-SPARKER AND CONTROL VALVE ASSEMBLY
5. CF-SPARKER Installation
• Locate CF-SPARKER inside of Crystal Fire burner box.
• Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out.
• Install CF-SPARKER into control panel as shown below.
• Press in CF-SPARKER button to test your sparker.
CONTROL VALVE
CONTROL PANEL
Fully tighten all screws after completing step 6
FOAM THIS SIDE

outdoorrooms.com 7
7. Screw tank tray onto bottom of the base as shown below.
BOTTOM COMPONENT ASSEMBLY
TANK TRAY

THE OUTDOOR
GREATROOM
COMPANY
SETTING UP YOUR BURNER
ATTENTION
Read and understand your Crystal Fire owner’s manual before beginning
burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
WARNING
Ensure valve is in the OFF position
before making any gas connections.
• For propane tank installations, install
included propane hose and regulator to
the control panel.
USE TWO WRENCHES TO ENSURE A
GAS TIGHT CONNECTION.
A. GAS CONNECTIONS
3.
•For hard piped installations. Connect
the gas supply line (not included) to
the 3/8” male are tting on the valve.
USE TWO WRENCHES TO ENSURE A
GAS TIGHT CONNECTION.
outdoorrooms.com 8
!
!
!!
PROPANE REGULATOR
OR GAS SUPPLY LINE
CONTROL VALVE
PROPANE HOSE

IMPORTANT
B. BURNER INSTALLATION
Please consult your Crystal Fire instruction manual for detailed instructions
and important information related to the burner installation including: lighting
and operating instructions, safety information, and proper tightening of
connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
outdoorrooms.com 9
• Ensure the correct orice is installed
for the fuel type you are using (see
Crystal Fire burner owner’s manual
included with burner for orice sizing
information).
• Ensure ex line is securely tightened
to the orice USE TWO WRENCHES TO
SECURE CONNECTION. One wrench
on ex line and one on the orice for
counter torque.
• Connect ex line to the control valve
USE TWO WRENCHES TO SECURE
CONNECTION.
ATTENTION
TIGHTEN ALL CONNECTIONS
SECURELY WITH TWO WRENCHES
• Carefully place burner into burner
opening.
• Orient burner so electrode is nearest
to the control panel in order to make
CF-SPARKER box connections.
!
!!
!
ORIFICE HEX
FLEX LINE HEX

C. ELECTRODE INSTALLATION
• Plug both BLACK wires hanging
from the burner into the back of the
CF-SPARKER. If an orange wire is present,
DO NOT USE IT. The orange wire is for
Direct Spark Ignition system only.
• Test system by pushing the button on
the igniter. Consult the troubleshooting
section of the Crystal Fire owner’s manual
if the spark is weak, intermittent or not
present.
outdoorrooms.com 10
D. PROPANE TANK INSTALLATION ATTENTION
HAND TIGHTEN, DO NOT USE A
WRENCH FOR THIS CONNECTION.
!!
• With the propane tank valve
and re pit valve o, attach the
propane regulator to the propane
tank.
• Place tank in tank tray.
• Ensure no hoses or wires are
contacting the bottom of the
burner.
•Replace the access door.
PROPANE REGULATOR
PROPANE TANK
ACCESS DOOR
TANK TRAY

outdoorrooms.com 11
A. FIRE MEDIA INSTALLATION
B. BURNER COVER INSTALLATION
• Scatter all included glass beads, lava
rock, or other approved re media
evenly across entire burner surface.
WARNING
DO NOT OPERATE CRYSTAL FIRE
BURNER WITHOUT INCLUDED GLASS
BEADS OR OTHER APPROVED FIRE
MEDIA.
WARNING
DO NOT OPERATE CRYSTAL FIRE
BURNER WITH BURNER COVER IN
PLACE.
4. MISCELLANEOUS
!
!
!
!
• Fully shut o gas supply to table and
turn control valve knob to OFF position.
Wait for burner to become cool before
placing glass cover.
• Carefully place the glass cover on top
of the burner.
• Remove glass burner before
attempting ignition.
(NOT INCLUDED)

outdoorrooms.com 12
OPERATING INSTRUCTIONS
IMPORTANT
Before operating your CAD-1224, ensure all gas connections are properly
tightened and thoroughly leak checked. Refer to the Crystal Fire manual for
information on proper leak checking and other critical safety information.
With the valve on the re pit in the
OFF position, open the valve on the
propane tank or natural gas supply.
Double check to make sure there
are no gas leaks at the regulator
or inlet side of the valve. If leak is
detected, immediately shut o the
gas supply and wait 5 minutes to
allow gas to dissipate. Fix any leaks
before proceeding.
Press the sparker button and hold,
look and listen for spark between
electrode and grounding rod.
While depressing the sparker, open
the valve.
If burner does not light after 10 seconds,
close the valve and wait 5 minutes to
allow gas to dissipate before attempting
ignition again.
ATTENTION
Refer to the Crystal Fire manual
included with your burner for
more detailed information on
operation, maintenance, and
safety of your burner.
1. Press in sparker 3. Turn valve to ON
2. Look/listen for spark
5.
!!
! !
THE OUTDOOR
GREATROOM
COMPANY
THE OUTDOOR
GREATROOM
COMPANY

outdoorrooms.com 13
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed instructions
and important information related to the burner installation including: light-
ing and operating instructions, safety information, and proper tightening of
connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember: before
operating, all gas connections must be fully checked for leaks.
6. WARNINGS
!
!
!
!

outdoorrooms.com
Thank you for purchasing an
Outdoor GreatRoom Company
product! This re pit was made
with pride in the USA.
Warranty: Fire pit tables are covered under a 1 year
manufacturer’s warranty.
Please visit http://www.outdoorrooms.com/product-registration
to register your product.
14400 Southcross Drive West • Suite 100 • Burnsville, MN 55306
Toll Free: 1-866-303-4028 • [email protected]