Palram Snap&Grow User manual

eStssemblyInstructions
Snap&Grow - Anchoring Kit
.0
sM
After Sale Service
Email: [email protected]
USA 877-627-8476 1 England 01302-380775
1
France 0169-791-094
Canada 1 800-866-5749 Germany 0180-522-8778 International [phone]
www.palramapplications.com

Before you start
IRItis highly recommendedto be assisted by a second person in some steps.
IRSortthe parts and check according to the contents parts list.
IRThe product must be positioned and fixed on a leveled surface.
IRMake sure that screws and anchors suit the surface type.
IRThis product is suitable for all Snap&Grow greenhouses up to 8 feet long.
Please be safe during assembly.
You will need
To assembly this product
(these items not supplied)
411
SafetyThis product should be mounted to the ground as shown in these instructions
LJ in order to ensure greenhouse's stability and appropriate wind resistance.
Some parts may have sharp edges. Please be careful when handling
components.
Always wear gloves, eye protection, and long sleeves when assembling or
performing any maintenance on your product.
If using a stepladder or power tools please ensure thatyou follow the
manufacturer's safety advice.
IRDO not lean the stepladder against the greenhouse.
IRDo not stand on the greenhouse roof/panels
IRTo prevent injuries, do not allow children to play under the greenhouse
during assembly.
Please read these instructions carefully before you start to
assemble this product.
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
Care and Maintenance
0Periodically check the product to assure that it remains stable.
0Keep roof clean ofsnow.
During Assembly
During assembly you will encounter the information icon, please
refer to the relevant assembly step for additional comments and
assistance.
Do not cut the steel cable unless a final decision on the mounting location
has been made.
Step 3 : According to the ground surface type, follow the appropriate
mounting procedure.
Option 1 : for hard surfaces (concrete or wood)
Option 2 : soft/ground installation.
Step 5 : After the product has been installed, fasten the steel cable by
turning part #7332
Tighten all screws when completing assembly.

Contents
Item Qty.
4010
4000
7409
7410
7333
7332
7331
4(+1)
4(+1)
Item Qty.
414
433
7283
7327
7336
2(+1)
6(+1)
2(+1)
2
4

1
7327 2
®+®
7410 2
11.11111111111

2
7409 4

3
7331 4
4000 11)MMONNOWNW 4
4010 4
433 4 7336 4
- -
45-55 cm
1'513/462
Ay_

14-
1
N
4114414 i 4
4 ' 41 4 4 ,
,41 ,
4
411
4
4,14 '44 ,
14 40 4,44, ,446_1
4
4,4 4,44
111111111Mil 44414 441
. 44 141 41 i
4
0 11KIV
4414 41141 4411::',,
141 6-i
'
4'
\ WO% 411,4 1'1
14
1
1 4 .,
11 4 1
1 , 4,
\ VMS 40 ',4, 4414
,
O 4 1 41 4 4'
44'1441411
\0All
111 1
41'1141'14
1 41 4 4
11 11'
41
4
4 14
4 4'11
4
1
.7r Co N N N

Master_SNG_Anchoring_Kit_V1-4