ParaBody 441101 440 User manual

441101 440 LEG PRESS ADAPTER KIT
Part # 7039101
REV. B Revision: 07/19/011
ASSEMBLY INSTRUCTIONS
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
IMPORTANT NOTES
1. Consult your physician before beginning any exercise program.
Please note:
Tools Required for Assembly
* Thank you for purchasing the Parabody 441101 Leg PressAdapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 5/32” Allen wrench
* Adjustable wrench
* Tape measure
2
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER:
3. Do not allow minors or children to play on or around this equipment.
2. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
4. Exercise with care to avoid injury.
5. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH

FIGURE 1
STEP 1
• Slide two COVER CAPS (7) over the FRONT LEG (1)
as shown in FIGURE 1
1
7
PARTS LIST
3
PART #
6686608
6693902
6694002
6694208
3116201
6405201
6467001
3108102
6140701
KEY
1
2
3
4
5
6
7
8
9
QTY
1
1
1
1
2
1
2
1
2
PART #
3102501
3102802
3102801
3102924
3102904
3102918
7032303
6694401
DESCRIPTION
3/8” WASHER
3/8” LOCKNUT
1/2” LOCKNUT
3/8 X 1-3/4” BOLT
3/8 X 3” BOLT
1/2 X 3-1/4” BOLT
110-3/4” CABLE ASSY
82-1/2” CABLEASSY
QTY
4
5
2
3
2
2
1
1
DESCRIPTION
FRONT LEG
PULLEYBRACKET
CABLESWIVEL
BASECONNECTION
3-1/2” PULLEY
2” SQ. END CAP
COVER CAP
QUICK DISCONNECT LINK
GLIDE 1 X 1”
KEY
10
11
12
13
14
15
16
17
FIGURE 2
4
6
STEP 2
• Slide one 2” SQ. END CAP (6) into the BASE CONNECTION (4)
as shown in FIGURE 2.
FIGURE 3
9
2
STEP 3
• Attach two 1 X 1” GLIDES (9) to the top of PULLEY BRACKET
(2) as shown in FIGURE 3.
NOTE: The LEG PRESS ATTACHTMENT (100101) must be assembled before connecting it to the
PARABODY 440 HOME GYM

FIGURE 4
FIGURE 5
1
4
1/2X3-1/4” 15
12
STEP 4
• Securely fasten the FRONT LEG (1) and the BASE CONNECTION (4) to the 440 HOME GYM using two 1/2 X 3-1/4” BOLTS
(15) and two 1/2” LOCKNUTS (12). See FIGURE 4.
STEP 5
• Remove one existing 3-1/2” PULLEYand two SPACERS
from theADJUSTMENTTUBE on the 100 LEG PRESS
OPTION by unfastening the 3/8 X 4-1/2” BOLTholding
the pulley on. See FIGURE 5. (Note: Save 3-1/2”
PULLEY, it will be used in later steps.)
4
0123456
1/2 1/2 1/2 1/2 1/2 1/2
3-1/2” PULLEY
2” WHEEL
3/8 X 4-1/2”
BOLT
SPACER

FIGURE 7
FIGURE 6
STEP 6
• Attach CABLE SWIVEL (3) to the
ADJUSTMENT TUBE on the 100 LEG
PRESS using the existing previously removed
3/8 X 4-1/2” BOLTS, WASHERS, 2”
WHEELS AND NUT. (Note: Securely
tighten, then back off 1/4 turn to allow the
CABLE SWIVEL & WHEELS to rotate
freely.) See FIGURE 6.
5
2” WHEEL
3/8 X 4-1/2” BOLT
NUT
2” WHEEL
STEP 7
• Securely fasten the 100 LEG PRESS to the FRONT LEG (1) using two 3/8 X 3” BOLTS (14), four 3/8” WASHERS (10), and two
3/8” LOCKNUTS (11) as shown in FIGURE 7.
1
10
10
11
3
3/8 X 3” 14

6
0123456
1/2 1/2 1/2 1/2 1/2 1/2
STEP 8
Remove the existing LAT CABLE using the following steps:
• Unscrew the threaded end of CABLE from the HEAD PLATE ASSEMBLY.
• Route the LAT CABLE around the PULLEY BLOCK as shown in FIGURE 8.
REMOVE CABLE
FIGURE 8
• The pulleys in TOP BOOM may need to be temporarily removed to remove CABLE.
• Route the LAT CABLE around the TOP BOOM as shown in FIGURE 8.
• Disconnect LAT BAR from TOP BOOM.

7
STEP 9
Install the NEW 110-3/4” CABLEASSY (16) using the following steps:
• Route the CABLE (16) back over one pulley in the TOP BOOM, down through the PULLEY BRACKET (2) and over the second
pulley in the TOP BOOM.
• Route the CABLE (16) around the PULLEY BLOCK as shown in FIGURE 9.
• Route the CABLE (16) through the TOP BOOM as shown in FIGURE 9. The pulleys in TOP BOOM may need to be temporarily
removed to perform this step. (Note: Make sure the CABLE is running OVER the BOLTS connecting the FRONT UPRIGHT
to the TOP BOOM. These may also have to be removed to perform this step.)
FIGURE 9
2
16
FIGURE 10
3/8 X 1-3/4” 13
16
11
2
STEP 10
• Loop CABLE (16) around one 3-1/2” PULLEY (5) in the PULLEY
BRACKET (2) using one 3/8 X 1-3/4” BOLT (13) and one 3/8”
LOCKNUT (11) as shown in FIGURE 10.
5
• Screw the threaded end of CABLE (16) into the HEAD PLATE
ASSEMBLY.
IMPORTANT: Cable must run over the top of
bolts.

FIGURE 11
STEP 11
• Attach the hook end of 82-1/2” CABLE (17) to the CABLE SWIVEL (3) with one QUICK DISCONNECT LINK (8).
IMPORTANT: Tighten the QUICK DISCONNECT LINK (8) securely.
8
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Route the 82-1/2” CABLE (17) under the WEIGHT STACK as shown in FIGURE 11.
8
3
17
IMPORTANT:
Tighten QUICK DISCONNECT LINK
SECURELY.

FIGURE 13
FIGURE 12
STEP 12
• Screw the threaded end of 82-1/2” CABLE (17) to the PULLEY
BRACKET (2) as shown in FIGURE 12.
STEP 13
• Attach one 3-1/2” PULLEY (5) to the FRONT LEG (1) and one 3-1/2” PULLEY (5) to the BASE CONNECTION (4) using two 3/
8 X 1-3/4” BOLTS (13) and two 3/8” LOCKNUTS (11). (Note: Make sure CABLE (17) is running under PULLEYS.)
9
2
17
5
3/8 X 1-3/4” 13
11
1 17
4

FIGURE 14
STEP 14
• The 100 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit
from the machine. To use, you must slightly push against the foot plates to take tension off the pin.
• To set the correct amount of tension in the cables, adjust the 100 LEG PRESS into the last adjustment hole (so the LEG PRESS is
spread apart) and remove the WEIGHT STACK PIN. Thread the 110-3/4” CABLE (16) into the HEAD PLATE ASSEMBLY until
the PULLEY BRACKET (2) is held against the TOPBOOM and the cable is slightly pulling up on the HEAD PLATE. Tighten the
jan but securely. Next, thread the 82-1/2” CABLE (17) into the PULLEY BRACKET (2) until cable is tight , then tighten the jam
nut securely.
10
0123456
1/2 1/2 1/2 1/2 1/2 1/2
2
17
16
SPRING PIN ADJUSTMENT
Thankyou forpurchasingthe Parabody441101LEGPRESSADAPTER KIT. Ifunsureofproperuseof
equipment,callyour local Parabody distributororcall the Parabodycustomerservicedepartment at (800)
328-9714.