ParaBody 887 User manual

1
887 LAT OPTION
CLASSH
PART # 7305601
REV.A Revision: 06/20/02
USER’S GUIDE
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
Version: 887108

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
j
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
IMPORTANT SAFETY INFORMATION
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Parts list..........................4
NOTE: In a continual effort to improve our products, specifications are subject to change
2001 Life Fitness, a division of Brunswick Corporation. All rights reserved.
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
Assembly Instructions.....4-13
General Maintenance.......14
Warranty Statement..........15
Product Services..............16
Insert-Registration Card
©

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the ParaBody 877 Lat Option. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
3
NOTE:BOLTLENGTHISMEASUREDFROMTHEUNDERSIDEOFTHE HEADOFTHEBOLT.
BOLT LENGTH RULER:
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure

4
PARTS LIST
PART #
LEA6800209
LEA6800610
LEA6800809
LEA6801009
LEA6801110
LEA6759810
LEA6274410
LEA6725310
LEA3116201
LEA3116101
LEA6802101
LEA6671601
LEA6692601
LEA3103102
LEA6140701
LEA6405201
LEA3116001
LEA6177001
LEA3119301
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
QTY
1
1
1
1
1
1
1
1
5
1
1
1
2
4
8
2
1
2
2
PART #
LEA6236701
LEA6412001
LEA3203301
LEA6542402
LEA6416601
LEA3235314
LEA3114401
LEA3114701
LEA3235316
LEA3235502
LEA3114403
LEA3114702
LEA3235211
LEA6480301
LEA3103801
LEA3235208
LEA3108102
LEA6075906
LEA3235216
DESCRIPTION
1-3/4”SQ.ENDCAP
SPRINGPINASSEMBLY
VINYLCAP
3/16X 1-3/4X5-1/4” PLATE
3/4X1-1/2”GLIDE
1/2X3-1/2”BOLT
1/2”WASHER
1/2”LOCKNUT
1/2X 4”BOLT
3/8”LOWHEIGHTLOCKNUT
3/8”WASHER
3/8”LOCKNUT
3/8X2-3/4”BOLT
3/8”FLANGESPACER
5/16”SNAPHOOK
3/8X 2”BOLT
1/4”QUICKLINK
12LINKCHAIN
3/8X 4”BOLT
QTY
1
1
2
2
1
1
2
1
1
3
14
9
6
8
3
2
1
1
4
DESCRIPTION
UPRIGHT
ADJFOOTSUPPORT
PULLEYHOUSING
TOPBOOM
LATBARSUPPORT
CARRIAGE
LOWROW BAR
LATBAR
3-1/2”PULLEY
4-1/2”PULLEY
115-1/4”CABLE
121-3/4”CABLE
3X 2”ENDCAP
1X8”GRIP
1X1”GLIDE
2”SQ.ENDCAP
1-1/4”SQ.RUBBERBUMPER
2-1/2X5-1/2” NON-SKIDSTRIP
2-1/2”ROUNDENDCAP
KEY
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
FIGURE 1
STEP 1:
• Remove four7/16” CAPPLUGSfromtheUPPER & LOWER CROSS SUPPORTS on the888SMITH MACHINEas shown in FIGURE 1.
7/16”CAPPLUG
7/16”CAP
PLUG

5
FIGURE 2
STEP2:
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• LOOSELYassemblethe PULLEYHOUSING(3)and the UPRIGHT(1) totheLOWERCROSS SUPPORTusing two 3/8X4” BOLTS
(38),four 3/8”WASHERS(30),and two3/8”LOWHEIGHTLOCKNUTS (29).See FIGURE 2.
3/8 X 4” 38
3/8”LOWHEIGHTLOCK NUT 29
3
16
LOWERCROSSSUPPORT
1
UPRIGHTFRAME
30
30
• NOTE:Itmay be necessarytoloosen the 1/2X3-1/4”BOLTSof theLOWERCROSSSUPPORTconnecting theUPRIGHT
FRAME beforebeginningSTEP2.
• Insertone2”SQ.ENDCAP(16)intotheend of the PULLEY HOUSING (3) as shown in FIGURE 2.
• Attach four 3/4 X 1-1/2” GLIDES (24) to the inside of the tube on the UPRIGHT (1) as shown in FIGURE 2 using the follow-
ing steps:
• Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES (24) are to be attached.
• Remove the 3/4 X 1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces.
• SECURELYassemble one SPRING PINASSEMBLY(21) to the spring pinbarrelonthe UPRIGHT(1). See FIGURE 3.
21
24

6
STEP 3:
FIGURE 3
• Insert two 2-1/2” ROUND END CAPS (19) into the ends of theADJ. FOOT SUPPORT (2) as shown in FIGURE 3.
• Insert one 1-3/4” END CAP(20) into the end of theADJ. FOOT SUPPORT (2) as shown in FIGURE 3.
• Attach four 3/4 X 1-1/2” GLIDES (24) to the outside of the ADJ FOOT SUPPORT (2) and four GLIDES to the inside of the
tube on the UPRIGHT (1) as shown in FIGURE 3 using the following steps:
• Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES (24) are to be attached.
• Remove the 3/4 X 1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces.
• Pullback on the SPRINGPIN(21) and CAREFULLYinsert theADJ. FOOTSUPPORT(2) intotheUPRIGHT(1)as shown inFIGURE3.
• Applytwo2-1/2X5-1/2” NON-SKID STRIPS (18) to theADJ. FOOTSUPPORT(2)as shown in FIGURE 3.
1
2
20
24
18
19

7
STEP4:
FIGURE 4
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Attach eight 1 X 1” GLIDES (15) to the ends the CARRIAGE (6) as shown in FIGURE 4 using the following steps:
• Thoroughly clean all surfaces where the 1 X 1” GLIDES (15) are to be attached.
• Remove the 1 X 1” GLIDES (15) from the paper backing and firmly apply them to all shown surfaces.
• Attach one 1-1/4” SQ. RUBBER BUMPER (17) to the underside of the angle on the CARRIAGE (6) as shown in FIGURE 4.
STEP5:
FIGURE 5
• CAREFULLYslidetheCARRIAGE (6)overthe UPRIGHT(1) asshownin FIGURE5.
• Insertone3 X 2” END CAP (13) into the end of the UPRIGHT (1). See FIGURE 5.
6
1
13
15
17
6

8
STEP6:
FIGURE 6
• LOOSELYassemble theTOPBOOM(4)tothe UPPER CROSS SUPPORTusingtwo3/8X 4” BOLTS (38), four 3/8”WASHERS (30)
andtwo 3/8”LOCKNUTS (31).See FIGURE 6.
STEP7:
FIGURE 7
• LOOSELYassembletheTOPBOOM (4) to the UPRIGHT (1) using one 1/2 X 4” BOLT(28),one1/2X3-1/2”BOLT (25), two 1/2”
WASHERS (26),andone1/2” LOCK NUTS (27) asshowninFIGURE 6.
• Insert one 3 X 2” END CAP (13) into the end of the TOP BOOM (4). See FIGURE 6.
• SECURELYtighten all connections made up to this point.
• SlidetwoVINYLCAPS(22) over the LATBAR SUPPORT(5) as shown in FIGURE 7.
• SECURELYassemblethe LATBARSUPPORT(5) totheTOPBOOM(4) using one3/8X 2-3/4” (32)andone 3/8” LOWHEIGHTLOCK
NUT(29).SeeFIGURE7.
38 3/8 X 4”
28 1/2 X 4”
1/2X3-1/2” 25
4 27
26
30
31
13
UPRIGHT
32 3/8X2-3/4
3/8” LOWHEIGHT 29
22
4
UPPERCROSS
SUPPORT
5
UPRIGHTFRAME
• NOTE:Itmaybenecessarytoloosen the 1/2X3-1/4”BOLTSofthe UPPER CROSSSUPPORTconnectingtheUPRIGHT
FRAME beforebeginningSTEP6.

9
0123456
1/2 1/2 1/2 1/2 1/2 1/2
STEP8:
FIGURE 8
• Routethe 115-1/4” CABLE (11) through the TOP BOOM (4) as shown inFIGURE 8.
• SECURELYassemblethree3-1/2”PULLEYS(9) intotheslotsoftheTOPBOOM(4)usingthree3/8X2-3/4”BOLTS(32),six3/8”FLANGE
SPACERS(33), and three 3/8” LOCK NUTS(31)asshown in FIGURE 8.(NOTE: Make surethecableis routedoverall the pulleys.)
3/8X 2-3/4” 32
9
4
11
33
31

STEP9:
FIGURE 9
10
31
• Place one 3-1/2” PULLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown
inFIGURE9.
• LOOSELY assembletwo 3/16 X 1-3/4 X 5-1/4” PLATES (23) to each side of the 3-1/2” PULLEY(9) usingone3/8X2”BOLT(35),
two3/8” WASHERS(30),and one 3/8” LOCKNUT(31).See FIGURE 9.
• Attach the CABLE (11) from the TOP BOOM (4) to the CARRIAGE (6) using one 1/4” QUICK LINK (36) as shown in FIGURE 9.
(IMPORTANT!SecurelytightenQUICKLINK.)
!IMPORTANT!
SECURELY
TIGHTEN
35 3/8 X 2”
36
4
30
23 11
9
6

11
STEP10:
FIGURE 10
• Route thethreadedendof the 121-3/4” CABLE (12) through the slot of the PULLEYHOUSING then SECURELYassemble one 4-1/2”
PULLEY(10)tothePULLEYHOUSING(3)usingtwo3/8X2-3/4”BOLTS (32), two3/8”FLANGESPACERS(33), two3/8”WASHERS
(30),and two3/8” LOCKNUTS(31).(NOTE:TheCABLE(12)shouldberoutedbetweenthepulleyandtheretainingboltasshownin
FIGURE10.)
323/8 X 2-3/4”
3
33
31
10
12
33

12
STEP11:
FIGURE 11
• Loopthe121-3/4” CABLE (12) around one3-1/2”PULLEY(9) as shown in FIGURE 11.
• LOOSELYassemble the3-1/2” PULLEY(9)to the3/16 X1-3/4 X5-1/4” PLATES (23)using one3/8 X2”BOLT(35),two3/8”WASHERS
(30),and one 3/8”LOCKNUT (31).SeeFIGURE 11.
• SECURELYthread the end of the 121-3/4” CABLE (12) 3/4 of the way into into the threaded housing on the UPRIGHT and SE-
CURELYtightenjamnut.
35 3/8 X ”
30
23
9
31
UPRIGHT
12
SECURELY
TIGHTEN
JAMNUT!
THREADEDEND
• SECURELYtightenthe two 3/8 X 2”BOLTS (35)ofthe3/16 X 1-3/4 X 5-1/4”PLATES(23).

13
STEP12:
FIGURE 12
Thankyouforpurchasingthe Parabody887LATOPTION.Ifunsureof properuseofequipment,callyour
localParabodydistributor or call the Parabodycustomer service department at [phone].
• Attach the LAT BAR (8) to the ball end of the upper CABLE (11) using one 5/16” SNAPHOOK (34) as shown in FIGURE 12.
• Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (12) using one 12-LINK CHAIN (37) and two 5/16” SNAP HOOKS
(34)as shown in FIGURE 12.
• Slide two 1 X 8” GRIPS (14) on the LOWROWBAR(7)and two 1 X 8” GRIPS (14) on the LATBAR (8) as shown in FIGURE12.
37
7
34
34 11
8
14
12
34
14

MAINTENANCE
MODEL #________________________
SERIAL #_________________________
DATE OF PURCHASE: _____________
DEALERS NAME: _________________
DEALERS PHONE #_______________
14
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your ParaBody customer service representative
at [phone].
* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury
* Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis
Thank you forpurchasing the ParaBody 887 Lat Option.
Please note:
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICEYOU WILLBEASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUTYOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.
SERIAL NUMBERLOCATION

15
NOTES:
LIMITED WARRANTY
ParaBodyextends the followingLIMITED WARRANTYto the original owner of the ParaBody products.The Warranty terms apply to IN HOMEUSEONLY.
1. LIMITED WARRANTYON FRAMEAND WELDS. If the frame of the ParaBody product or aweld shouldcrack orbreak, itwill berepaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
2. LIMITEDWARRANTYON PARTS. Ifthe following partsaredefectivein materialor workmanship,ParaBody will supplyreplacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.
4. CONDITIONSAND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty.
5. REPLACEMENTAND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsiblefor allother costs. Such costs may include,but arenot limitedto: a. labor charges for service,removal, repairor reinstallation
oftheParaBody productorany componentpart; b.shipping,delivery, handlingandadministrative chargesforreturning partstoParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.
6. SHIPPING. Ifshipping bythe Ownersis deemed necessary(in solediscretion ofParaBody), partsshould be shippedin theiroriginal carton
orequivalent packaging,fully insuredwith shipping charges prepaid. ParaBody will not assumeany responsibilityfor anyloss ordamage
incurredin shipping.
7. CLAIM PROCEDURES. If service on your ParaBody product is required during thewarranty period,please contactour CustomerService
Departmentat1-800-328-9714for instructions regardingreturningorreplacingparts. Please have availablethefollowinginformation: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawingincluded with your assembly instruction); (iv) adescription ofthe nature of the problem.
8. OWNER’SRIGHT. ThisLimited Warrantygivesyou specificlegalrights. Youmay also haveother rights, whichvarydepending onlocal law.
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description inthis Limited Warranty.
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warrantyhas beenmade orwill be made on behalf of ParaBodywith respectto anyParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody
product,inconvenience, lossor damageto personalproperty, whether direct or indirect, and incidental or consequentialdamages, sothe
above limitation or exclusion may not apply to you.

INTERNATIONALOFFICES
LifeFitnessAtlanticBV
AtlanticHeadquarters
Bijdorpplein 25-31
2992LBBarendrecht
The Netherlands
Phone: [phone]
Fax: [phone]
Life Fitness Japan
8/F, Nippon Brunswick Building
5-27-7Sendagaya
Shibuya-Ku, Tokyo 151-0051
Japan
Phone: [phone]
Fax:[phone]
Life Fitness (UK) Ltd.
QueenAdelaide
Ely, Cambs CB7 4UB
United Kingdom
Phone CSS: [phone]
Fax CSS: [phone]
Life Fitness Benelux N.V.
Bijdorpplein 25-31
2992LBBarendrecht
The Netherlands
Phone: [phone]
Fax: [phone]
LIFE FITNESS
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.
Tel: [phone] Fax: [phone]
800.328.9714 (Toll-free within the U.S. and Canada)
www.parabody.com
16
LifeFitnessEUROPE GmbH
Siemensstrasse 3
85716Unterschleissheim
Germany
Phone: [phone]
Fax: [phone]
Life Fitness Italia S.R.L.
Via Elvas 92
39042Bressanone
Italy
Phone: [phone]
Fax: [phone]
Life FitnessAsia Pacific Limited
Room 2610, Miramar Tower
132 Nathan Road, Tsimshatsui
Kowloon, Hong Kong
Phone: [phone]
Fax: [phone]
Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3ºandar (Confab)
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Brazil
Phone:[phone]
Fax:[phone]