ParaBody 893104 User manual

893104 PRO SYSTEM
Part # 6817401 Revision:6/8/991
ASSEMBLY INSTRUCTIONS

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the Parabody 893104 PRO SYSTEM. Please read these instructions
thoroughly and keep them for future reference. This product must be assembled on a flat, level
surface to assure its proper function.
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
2
NOTE:BOLTLENGTHISMEASURED FROMTHEUNDERSIDEOFTHEHEADOFTHEBOLT.
BOLT LENGTH RULER:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
BoltLengthRuler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
WELCOMETOTHEWORLDOF Serious steel!
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].
BOLT LENGTH
5. Consult a physician before beginning any exercise program.

3
PARTS LIST
3
PART #
6816103
6815703
6815203
6814803
6815003
6816302
6798103
6801102
6275302
6274402
6807602
6807702
6546302
6812402
6194601
3116201
3116101
6816401
6692601
3103102
6140701
6405201
3116001
6817101
6811701
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
QTY
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
5
1
2
3
4
9
5
1
2
4
PART #
6824601
6542402
3105303
3105303
3102901
3102933
3102922
3102906
3102928
3102910
3102918
3102917
3102949
6480301
3102501
3102807
3102801
3102502
3102801
6606801
3105401
3103801
3108102
6075906
DESCRIPTION
3-1/4X1-3/4”GLIDE
1/2X3”VINYLCAP
3/16X1-3/4X5-1/4” PLATE
9/16”CAPPLUG
3/8X1-1/4”BOLT
3/8X2”BOLT
3/8X2-3/4”BOLT
3/8X4”BOLT
1/2X2-1/2”BOLT
1/2X3”BOLT
1/2X3-1/4”BOLT
1/2X4”BOLT
1/2X5-1/2”BOLT
3/8”FLANGESPACER
3/8”WASHER
3/8”LOWHEIGHTLOCKNUT
3/8”LOCK NUT
1/2”WASHER
1/2”LOCK NUT
1/2”SPRINGPINASSEMBLY
3/4”STARLOCKCOLLAR
5/16”SNAPHOOK
1/4”QUICKLINK
12LINKCHAIN
QTY
6
2
2
8
1
2
7
2
1
9
2
4
1
8
12
1
11
12
16
1
2
3
1
1
DESCRIPTION
TOPBOOM
UPRIGHTFRAME
KNEESUPPORT
UPRIGHTSUPPORT
FRONTUPRIGHT
FOOTPLATE
UPPERCROSSSUPPORT
LATBARSUPPORT
LATBAR
LOWROWBAR
LEFTSAFETYRAIL
RIGHTSAFETYRAIL
CARRIAGE
SMARTRACK
4X 7”ROLLERPAD
3-1/2”PULLEY
4-1/2”PULLEY
121-1/2”CABLE
3X2”ENDCAP
1X8”GRIP
1”SQ.GLIDE
2”SQ.ENDCAP
1-1/4”SQ.RUBBERBUMPER
1-5/8X5-1/2” NON-SKIDSTRIP
13-1/2X1-5/8”RUBBERSTRIP
KEY
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
FIGURE 1
STEP1:
• Applyeight 1”SQ. GLIDES(21)to theinside of the CARRIAGE (13) as shownin FIGURE 1.
• Attachone 1-1/4” SQ. RUBBER BUMPER (23) to the bottom of the CARRIAGE (13) as shown in FIGURE 1.
21
23
21
13

4
FIGURE 3
STEP3:
• LOOSELYassemblethe FRONTUPRIGHTS (5)totheUPRIGHTSUPPORT(4)usingfour1/2X4”BOLTS(37),four1/2”WASHERS(43),
andfour 1/2” LOCKNUTS(44) asshown in FIGURE3.
• Insertfour 2” SQ. END CAPS (22) & two 3 X 2” ENDCAPS (19) to the ends of the FRONT UPRIGHTS (5) as shownin FIGURE 3.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
44
43
19
5
4
1/2 X 4” 37
22
FIGURE 2
STEP2:
• Attachtwo NON-SKID STRIPS (24) to the FOOT
PLATE(6)as shown inFIGURE 2.
6
24
25
• Assembletwo 13-1/2 X 1-5/8” RUBBERSTRIPS (25)to the bottom of the FRONT UPRIGHTS(5) as shown in FIGURE 3.

5
• LOOSELYassembletheFOOTPLATE (6) and the UPRIGHTFRAME(2)totheUPRIGHTSUPPORT(4) using two 1/2” X 3-1/4” BOLTS
(36)and two 1/2”LOCK NUTS (44) as shownin FIGURE 4.
FIGURE 4
STEP4:
44
2
4
1/2X 3-1/4” 36
22
13
5
• Slidethe CARRIAGE (13)over theUPRIGHT FRAME (2)as shownin FIGURE 4.
• Insert one 2” SQ. END CAPS (22) to the end of the UPRIGHT FRAME (2) as shown in FIGURE 4.
6

6
0123456
1/2 1/2 1/2 1/2 1/2 1/2
FIGURE 5
STEP5:
• LOOSELYassemble the UPPERCROSSSUPPORT(7) tothetopsetofholesof the FRONTUPRIGHTS(5)asshowninFIGURE5 using
two1/2 X 3” BOLTS(35),two 1/2”WASHERS(43),and two 1/2”LOCK NUTS (44).
35 1/2 X 3”
14
43
2
7
5
1/2 X 3” 35
43
44
• LOOSELYassemble the twoSMARTRACKS (14) to the outside of the FRONTUPRIGHTS (5) as shown in FIGURE 5 using six 1/2 X
3”BOLTS (35), four 1/2”WASHERS (43),andsix1/2” LOCK NUTS (44).
44

7
FIGURE 6
STEP6:
• Attach six 3-1/4 X 1-3/4” GLIDES (26) to the LEFT & RIGHT SAFETY RAILS (11 & 12) as shown in FIGURE 6, using the
following steps:
• Thoroughly clean all surfaces where the 3-1/4 X 1-3/4” GLIDES (26) are to be attached.
• Remove the 3-1/4 X 1-3/4”” GLIDES (26) from the paper backing and firmly apply them flush with all shown surfaces.
12
26
11
• Attach two 13-1/2 X 1-5/8” RUBBER STRIPS (25) to the LEFT & RIGHT SAFETY RAILS (11 & 12) as shown in FIGURE 6.
25
• AssembletheLEFT& RIGHT SAFETYRAILS (11 &12) to theFRONT UPRIGHTS (5) as shownin FIGURE 7.
12
12
FIGURE 7
STEP7:
11
5

8
STEP8:
FIGURE 8
STEP9:
FIGURE 9
• LOOSELYassemble theTOPBOOM(1)to theUPRIGHTFRAME (2) using one 1/2 X 2-1/2” BOLTS(34), one1/2 X3” BOLT(35),
two1/2”WASHERS (43), and one 1/2” LOCK NUT (44) as shown in FIGURE 8.
• Insert one 3 X 2” END CAP (19) into the end of the TOP BOOM (1). See FIGURE 8.
• SlidetwoVINYLCAPS (27) over the LATBAR SUPPORT(8) as shown in FIGURE9.
• SECURELYassemble theLATBAR SUPPORT(8)to theTOPBOOM(1)usingone3/8 X 2-3/4”(32)and one 3/8”LOWHEIGHTLOCK
NUT(41). SeeFIGURE9.
33 3/8 X 4”
32 3/8 X 2-3/4”
1/2X2-1/2” 34
1 44
43
40
42
19
32 3/8 X 2-3/4”
3/8”LOWHEIGHT 41
27
1
8
42
*SECURELYTIGHTENALLLOOSECONNECTIONSMADEUPTOTHISPOINT!
5
7
2
• LOOSELYassemble the TOPBOOM(1) tothe UPPER CROSS SUPPORT(7) using two3/8 X4” BOLTS (33),four 3/8”WASHERS
(40)andtwo3/8”LOCKNUTS(42). See FIGURE 8.
• LOOSELYassemble theTOPBOOM(1) to the UPRIGHTFRAME (2) using one 3/8 X 2-3/4” BOLTS(32) and one 3/8” LOCK NUT
(42)as shown inFIGURE 8.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
35 1/2 X 3”

9
STEP10:
FIGURE 10
• Routeone CABLE(18) throughthe TOPBOOM (1)as shown inFIGURE 10.(NOTE: Makesure CABLEis routedoverbolt!)
• SECURELYassemble three 3-1/2” PULLEYS (16) into the slots of the TOPBOOM (1) using three 3/8 X 2-3/4” BOLTS (32), six 3/8”
FLANGESPACERS (39), andthree3/8” LOCK NUTS(42)as shown inFIGURE10. (NOTE:Makesurethecableisroutedoverallthe
pulleys.)
3/8 X 2-3/4” 32
16
1
18
39
42
Makesure CABLE
is routed overbolt!

STEP11:
FIGURE 11
42
• Place one 3-1/2” PULLEY (16) into the loop of the CABLE (18) below the second and third PULLEY of the TOP BOOM (1) as shown
inFIGURE11.
• LOOSELYassembletwo 3/16 X 1-3/4 X 5-1/4” PLATES(28) to each side of the 3-1/2” PULLEY(16) using one 3/8 X 2” BOLT(31),
two3/8”WASHERS (40),and one 3/8”LOCK NUT(42).See FIGURE 11.
• Attach the CABLE (18) from the TOP BOOM (1) to the CARRIAGE (13) using one 1/4” QUICK LINK (48) as shown in FIGURE 11.
(IMPORTANT!SecurelytightenQUICKLINK.)
!IMPORTANT!
SECURELY
TIGHTEN
31 3/8 X 2”
48
1
40
28
18
16
13
10
0123456
1/2 1/2 1/2 1/2 1/2 1/2