ParaBody GS6-LP5A-101 User manual

1
LEG PRESS ADAPTER KIT
CLASS H
PART#7363201
REV. A Revision: 11/01/02
USER’S GUIDE
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
FOR GS6 GYM SYSTEM
Version:GS6-LP5A-101

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
j
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
IMPORTANT SAFETY INFORMATION
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
NOTE: In a continual effort to improve our products, specifications are subject to change
2002 Life Fitness, a division of Brunswick Corporation. All rights reserved.
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
Parts list..........................4
Assembly Instructions.....4-12
Insert-Registration Card
©

IMPORTANT NOTES
Please note:
Tools Required for Assembly
* Thank you for purchasing the ParaBody GS6 Leg Press Adapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* 9/16” wrench
* Ratchet with 9/16” socket
*Adjustable wrench
* Tape measure
3
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OF THE BOLT.
BOLT LENGTH RULER:
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH

PARTS LIST
4
NOTE: TheLEGPRESSATTACHMENT(LP5)mustbeassembledbeforeconnectingittothePARABODYGS6GYMSYSTEM
PART #
ACU04-1552
ACU04-1172
ACU04-1553
ACU04-1171
ACU02-0055
ACU13-0155
ACU13-0156
ACU06-0024
ACUDA1E03843416NB
QTY
1
1
1
1
1
1
1
7
4
PART #
ACUDA1E03833416NB
ACUDA1E03823416NB
ACUDA1E03813416NB
ACUDC1250100020B
ACUDB2E03811000B
ACU05-0381
ACU08-0085
ACU08-0079
ACU08-0076
DESCRIPTION
3/8”X3-3/4” BOLT
3/8X2-3/4”BOLT
3/8X1-3/4”BOLT
3/8”WASHER
3/8”LOCK NUT
5/16X15/16”SPACER
STEPSPACER 19/32”
STEPSPACER1-11/16”
STEPSPACER 1-19/32”
QTY
7
1
4
9
16
1
2
2
2
DESCRIPTION
CONNECTINGTUBE
FLOATINGPULLEYBRACKET
PULLEYHOUSING
PULLEYGUARD
CABLERETAINER
LATCABLE 128-3/4”
LEGPRESSCABLE160-3/4
3-1/2”PULLEY
3/8X4-3/4”BOLT
KEY
10
11
12
13
14
15
16
17
18
KEY
1
2
3
4
5
6
7
8
9
FIGURE 1
STEP 1:
• SECURELYassembletheLEGPRESStottheCONNECTINGTUBE(1) using two 3/8 X 3-3/4”BOLTS (10), two 3/8”WASHERS(13)and
two3/8” LOCKNUTS (14) as shown in FIGURE 1.
• RemoveEND CAPfromthe BASEand insert new CONNECTINGTUBE(1) using two 3/8 X 3-3/4” BOLTS(10), four 3/8”WASHERS
( 13) and two 3/8” LOCK NUTS (14). Re-install endcap.
1
BASE
LEGPRESS
0123456
1/2 1/2 1/2 1/2 1/2 1/2
3/8X 3-3/4” 10
13
14
10 3/8X 3-3/4”
13
14

5
FIGURE 3
STEP3:
• Remove and DISCARD the LAT CABLE as shown in FIGURE 3.
LATCABLE
DISCARD!
• Install the PULLEYHOUSING (3) to the BASE using two 3/8 X 3-3/4” BOLTS (10) and two 3/8” LOCK NUTS (14) as shown in
FIGURE2
FIGURE 2
STEP 2:
BASE
10 3/8X 3-3/4”
14
3

6
FIGURE 4
STEP4:
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• SECURELYassembleone 3-1/2 PULLEY(8)to the FLOATING PULLEYBRACKET(2)using one 3/8 X 1-3/4”BOLT(12)andone3/8”
LOCKNUT(14)as shown in FIGURE 4.
• RoutetheLATCABLE(6) around the the PULLEYS in the TOPPLATEASSEMBLY. SECURELYassembleone3-1/2”PULLEY(8) to the
TOPPLATEASSEMBLE using one 3/8X 3-3/4”BOLT(10), one PULLEYGUARD (4), one 5/16 X 15/16” SPACER (15) and one3/8”
LOCKNUT (14)as shown in FIGURE 4. Finish routing the LATCABLE through the FRONTFRAME.
• Screw the threaded end of the new LAT CABLE (6) into the end of the HEAD PLATEASSEMBLY.
8
14
4
8
15
6
3/8X 1-3/4” 12
3/8X 3-3/4” 10
14
TOPPLATEASSEMBLY
2
FRONTFRAME

FIGURE 5
7
STEP5:
• Assemble one3-1/2PULLEY(8)tothePULLEYHOUSING (3)usingone 3/8X1-3/4”BOLT(12)andone3/8”LOCKNUT(14) asshown
inFIGURE5. (NOTE: LEGCABLEMUSTBEPLACEDIN PULLEYHOUSINGBEFOREINSTALLING PULLEY)
• Screwthe threaded end of the LEG PRESS CABLE (7) into the endof the FLOATING PULLEYBRACKET(2) as shown in FIGURE 5.
3
14 8
7
2
12 3/8X 1-3/4”

8
FIGURE 6
STEP6:
SEATFRAME
14
13
7
8
12 3/8X 1-3/4”
5
BRACKET
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Carefully route the LEG PRESS CABLE (7) around one 3-1/2” PULLEY(8) and SECURELYassemble the 3-1/2” PULLEY(8) to the
BRACKET(from the LP5 LEGPRESS) using one3/8 X 1-3/4” BOLT(12), one 3/8”WASHER (13),one CABLE RETAINER (5)
and one 3/8” LOCK NUT (14) as shown in FIGURE 5. Make sure the CABLE is in the grooves of all the pulleys.

9
FIGURE 8
STEP 8:
• Carefully route the LEG PRESS CABLE (7) around one 3-1/2” PULLEY(8) and SECURELYassemble the 3-1/2” PULLEY (5) to the
bracket on the SEAT FRAME using one 3/8 X 1-3/4” BOLT (12) and one 3/8” LOCK NUT(14) as shown in FIGURE 8 . Make sure the
CABLE is in the grooves of all the pulleys.
3/8X 1-3/4” 12
8
714
SEATFRAME
FIGURE 7
STEP7:
9
SEAT FRAME
• SECURELYattachthe BRACKET (from LP5LEG PRESS) tothe SEATFRAMEusing two 3/8”X 4-3/4” BOLTS (9), two3/8”WASH-
ERS(13),andtwo3/8”LOCKNUTS(14).SeeFIGURE7.
13
14
BRACKET
3/8X 4-3/4”

FIGURE 9
STEP9:
• CarefullyroutetheLEGPRESSCABLE (7) around one 3-1/2”PULLEY(8)andSECURELYassemble the3-1/2”PULLEY(8) to the SEAT
FRAMEusingone3/8X4-3/4”BOLT(9),two1-19/32” STEPSPACERS (18) and one 3/8” LOCKNUT(14)as shown in FIGURE 9. Make
sure the CABLE is in the grooves of all the pulleys.
3/8 X 4-3/4” 9
8
7
14
18
MAINARM
FIGURE 10
STEP10:
• Carefullyroute the LEG PRESS CABLE (7) around one 3-1/2” PULLEY(8)and SECURELYassemble the 3-1/2” PULLEY(8) to the
MAINARM using one 3/8 X 2-3/4” BOLT (11), two 19/32” STEPSPACERS (16) and one 3/8” LOCK NUT (14) as shown in FIGURE
10. Make sure the CABLE is in the grooves of all the pulleys.
3/8X 2-3/4” 11
8
7
14
16
10
SEATFRAME