ParaBody 829102 User manual

Serious
I II
829102 LEG CURL/EXTENSION
I I I I
/
/
I I
ASSEMBLY INSTRUCTIONS
Part # 6668901 Revision: 09/12/97

Pleasenote:
* Thznkyou for purchasing the Parabody829102LegCurl/Extension. Please read these
instructions thoroughlyand keepthemfor future reference. This product mustbe assembled
ona flat, level surfaceto assureits properfunction.
* Werecommendcleaning your product (pads and frame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedfrom your Parabodycustomerservice representative
at [phone].
Thereis a risk assumedby individuals whouse this type of equipment.Tominimizerisk, please
followthese rules:
1. Inspect equipmentdaily. Tightenall loose connectionsand replace wornparts immediately.
Failure to doso mayresult in serious injury.
2. Donot allow minorsor children to play on or aroundthis equipment.
3. Exercisewith care to avoidinjury.
4. If unsureof proper use of equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
[ Req for, .A, ~ ’bly[
Tools uired sem
* Rubber mallet or hammer
* 3/4" wrench
* 9/16" wrench
* Ratchet with 3/4" and9/16" sockets
*Adjustable wrench
*Tape measure
[Bolt LengthRuler
NOTE: BOLT LENGTtt IS MEASUREDFROMTHE UNDERSII)E OF TIlE HEADOF THE BOLT.
’ I!iiiiiiil
BOLT LENGTH RULER:
0 1 2 3 [ ,I I I

PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PART #"’ DESCRIPTION,.’
6259103 FRONT SUPPORT TUBE,
6625402 BACK. PAD ADJUST TUBE
6625502’ BACK PAD SUPPORT’~-BE
6216~02’ 1-3/4 SQ X 5" TUBE
6668i02" 1-3/4 SQ X 13-112" TUBE
666200i’ LEG CURL/F_,XTENSION
6661202 BACK PAD ASS~
66616oi SEATPADAssY
666220~ LEG EXT HANDLE ’~
666230~’ LEG EXT HANDLELFT
666850~ LEG FRAME
666190~ REARBASELE’(~
6125101 3/4 X 16" TUBE
654930i 3/4 X 17" TUB~’
619460i 4 X 7" ROLLERP~D
662830i 1/8 X 2 X 8" PLATE
641206i 3/8" DIA SPRINGPIN
646690’i 1/2" DIA SPRING~IN
310290--------~ 3/8 X 1" BOLT
LEG EXTENSION
1
I
1
I
1
1.
1
1
1
1
1
I
2
1
6
1
2
1
4
~’~/’ PART#
20 3102904
21 3102906
22 3102917
23 3192-°-G1
~
24 3102501
25. 3102801
26 ~102804
27 3102807
28 6405201
29 6692601
30 3102416
31 6406401
32 3104301
33 6416601
34 3107801
35 3105401
36 3103101
37 6467001
DESCRIPTION
3/8 X 3" BOLT
3/8 X 4" BOLT
1/2, X4" BOLT
112 X 7" BOLT
318" FLAT WAS~-IK
3/8" :N’YLOCKNUT
1/2" LOWI-IT. NYLOCKNUT
3/8" LOWl-IT. NYLOCKNUT
2" SQ ENDCAP
3 ~[ 2" ENDCAP
2 ~[ 1" ENDCAP
HINGE TAB
3/4" SQ RUBBERBUMPER
1-1/2 X3/4" GLIDE(QTY"8)
1/2" FLANGE BEARING
STA]~LOCK COLLAR
1.,1/4 X 5" GRIP
PARABODYLOGO END CAP
20
4
2
2
3
2
4
2
2
2
6
4
4

STEP1:
STEP2:
Insert four PARABODYLOGOEND
CAPS(37) into the ends of REARBASE
LEG (12) and FRONTBASESUPPORT
(1). See FIGURE
Slide two1-I/4 x 5" GRIPS(36) over tubes
on REAR.BASELEG(12). See FIGURE
1. "
STEP3: Securely assemble REARBASELEG(12)
to LEGFRAME(11) using two 3/8 X
BOLTS(20), four 3/8" FLATWASHERS
(24), and two 3/8" NYLOCKNUTS(25).
See FIGURE2.
STEP4: Securely assemble FRONTBASESUP-
~~ LEGFtL~-:~ (11) using two
PORT(~.) ,.~.
3/8 X3" BOLTS(20), four 3/8" FLAT
WASHERS(24), and two 3/8" NYLOCK
NUTS(25). See FIGUR~
STEP5: Slide two 1-1/4 X 5" GRIPS(37) over
RIGHT LEG EXT HANDLE(9) & LEFT
LEGEXTHANDLE(10). See FIGURE
FIGURE2 ~ 3/8 x y’
FIGURE4

STEP6:Securely assemble RIGHT(9) &I.EFT
(10) LEG EXT HANDLES to LEG
FRAME(11) using two 3/8 X 4" BOLTS
(21), four 3/8" FLATWASHERS,and two
3/8" LOWHEIGHT NYLOCKNUTS
(27). See FIGURE
STEP7:Insert two 3 X 2" ENDCAPS(29) into
the leg fi:ame as shownin FIGURE5.
STEP8:Securely assemble one 1/2" SPRINGPINAS-
SEMBLY(18) into the spring pin barrel on the
LEGFRAME(11) as shown in FIGURE
STEP9:Insert four 2 X1" ENDCAPS(30) into the ends
of the BACKPADADJUSTTUBE(2) & BACK
PADSUPPORTTUBE(3). See FIGURE
FIGURE 6
FIGURE 7 ~

STEP 10: Securely assemble BACKPADADJUST
TUBE (2) & BACKPAD SUPPORTTUBE
(3) to LEGFRAME(11) using one 1/2
BOLT(23) and one 1/2" LOWHEIGHT
NYLOCKNUT (26). (NOTE: SECURELY
TIGHTENBOLT THEN BACK NUT OFF
1/4 TURNTO ALLOWTHE TWOPARTS
TO ROTATEFREELY.) See FIGURE8.
FIGURE8
1/2 X7
STEP11: Securely attach the BACKPAD(7)
to the BACKPADTUBES(2 & 3)
using four 3/8 X 3" BOLTS(20)
and four 3/8" FLATWASHERS
(24). See FIGURE
FIGURE 9
3/8 X3"
STEP12: Securely fasten 2 X8" PLATE(16) to bottom of SEAT
PAD(8) using two 3/8 X 1" BOLTS(19) and two
FLATWASHERS(24). See FIGURE10.
FIGURE 10 3/8 X1"

STEP13: Slide two H]NGETABS(31) over posts
LEGFRAME(I 1). See FIGURE11.
FIGURE 11 (~
STEP14: Securely attach the SEATPAD(8) to the
HINGETABS(31) using two 3/8 X
BOLTS(19) and two 3/8" FLATWASH-
ERS(24). See FIGURE12.
FIGURE 12
STEP15: Attach two ROLLERPADS(15) to the
LEGFRAME(11) using one 17" ROLLER
PAD SHAP~(14) and two STARLOCK
COLLARS(35). See FIGURE13.
/ /

STEP16: Attach eight 1-1/2" X 3/4" GLIDES(33) to
ROLI.ERPADADJUSTER(4) and attach eight
1-1/2" X 3/4" GLIDES(33) to 13-1/2" ROLLER
PADADJUSTER(5) as shown in FIGURE14.
FIGURE
STEP17: Securely assemble two 3/8" SPRINGPIN AS-
SEMBLIES(17) into the spring pin barrels
the LEGCURL/EXTENSION(6) as shown
FIGURE15.
FIGURE 15
STEP18:
STEP19:
Insert 5" & 13-1/2" ROLLERPAD
~r3~I~TI~,RS(4 &5) in the ends of the
LEGCURL/EXTENSION(6). Pull back
on SPRINGPINS until ROLLERPAD
ADJUSTERS(4 &5) lock in place. See
FIGURE16.
Insert three 2" SQUAREENDCAPS(28)
into the ends of the LEGCURL/EXTEN-
SION(6). See FIGURE16.
FIGURE 16

STEP20:Insert two 1/2" FLANGEBEARINGS
(34) into the LEGCUR/JEXTENSION
(6). See FIGURE17.
STEP 21:Securely assemble LEGCURL/EX-
TENSION(6) to LEG FRAME(11)
using one 1/2 X 4" BOLT(22) and one
1/2" LOWHEIGHT NYLOCKNUT
(26). (NOTE: SECIYRELYTIGHT-
EN BOLT THEN BACK NUT ,OFF
1/4 TURN TO ALLOWTHE PART ,
TO ROTATEFREELY.) See FIG- [~I/2X 4"
BUMPER(32) betweenthe contact point
ofthe LEGCURL/EXTENSION(6) and I,G.URE 17
the LEGFRAME(11).See FIGURE17.
STEP23:Attach four ROLLERPADS(15) to the LEGCURL/EXTENS]:ON(6) using two
ROLLERPADSHAFTS(13) and four STARLOCKCOLLARS(35). See FIGURE
TI~IS CONCLUDEST_Wi~.~ ASSEMBLY
OF TIlE PARABODY829102
LEG CURL/EXTENSION
FIGURE 18
1 [ I I0[I I II I .
I
3
I9