ParaBody 888101 User manual

888101 SNI][TH NIACH][NE
ASSEMBLY ]INSTRUCTIONS
Part # 6801501 1 Revision.:2/10/99

WELCOMETO THE WORLDOF ~,~i~u$ ~ee~
~.
Please note:
* Thar~kyou for purchasing the Parabody888101SMITEIMACHINE.Please read these in-
structions thoroughlyand keep themfor future reference. This product mustbe assembledon
a flat, level surfaceto assureits properfunction.
Werecommendcleaning your product (pads and frame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedfromyour Parabodycustomerservice representative
at [phone].
Thereis a risk assumedby individuals whouse this type of equipment.Toi~nhx~zerisk, please
followthese ruleS:
1. Laspectequipmentdaily. Tightenall loose connectionsandreplace wornparts immediately.
Failureto dosomayresult in serious injury.
2. Donot allow minorsor children to play on or aroundthis equipment.
3. Exercisewithcare to avoidinjury.
4. If unsureof properuse of equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
5. Consult a physician before berg any exercise program.
I Tools Requiredfor Assembly[
* 3/4" wrench
*9/16" wrench
* Ratchet with 3/4" and9/16" sockets
* 7/32" Allen wrench
*Adjustable wrench
* Tape measure
Bolt LengthRuler
NOTE: BOLT LENGTtt IS MEASUREDFROM TI~E UNDERSII)E OF TttE HEAD OF THE BOLT.
.11///////I
BOLT LENGTH RULER:
1/2 1 1/2 [ 1/2 11/2 [ 1/2
3 4 1/2 1

1’" 6798103
’2 679~103
367985O2
46798402
~679~702
66798901
76799601
"8 ,. 6799203
96799801
’10 6714901
11 32030o2[
PART
LOWERCROSS BRACE
SMrrl-IBk~
POD
GLm)ERODBUSH]NO
1" SHAFFCOLLAR
2
.22
2
4
12
13
14
15
" 16
18
19
"20
21
~,artT# iizsc~ r~o~
6692601 3 x2- ENDCAP
3102"910 "a/2X3eC,~r
3102502
3102~01
3105302
3105303
6824601
6695801
3109302
6807101
7/16"HO1 ;]?LUG
9/16"HO1 EPLUG
3 - 1/~ X1-3/ GL/DE
2 I/2" ODRUBI !RBUMPER
6’
12
8
16
6 ,
zk I
FIGURE1
STEP1:
¯ Insert two 1-3/4" ROUNDENDCAPS(20) into the end of NePLATEHOLDERS(7) as shownin FIGURE

1/2X3"~
FIGURE 2
STEP2:
¯LOOSELYassemblethe PLATEHOLDEP--S(7) andtheLOWERCROSSSUPPORT(2) totheUPRIGIff-f FRAMES(8) as
FIGURE2 using four 1/2 X3" BOLTS(13), andfour 1/2" LOCKNUTS(15),
¯LOOSELYassembletheUPPERCROSSSUPPORT(1)tothetopsetofholesoftheupRIGHTFRAMES(8)assh°wninFIGURE2nsing
two1/2 X3"BOLTS(13), two1/2" WASHERS(14), andtwo/2"LOCKNUTS(15).
¯ LOOSELYassemblethe GUNRACKS(21) to the outside of the UPRIGHTFRAMES(8) as sho~inFIGURE2 using six 1/2 X3" BOLTS
(13), fo~ 1/2" WASHERS(14), arid six 1/2" LOCKNUTS(15).
SECURELYtighten all connectionsmadeto up to this point.
~ 1/2 I 1/2 i 1/~

I
I
I
FIGURE 3
STEP3:
¯ Insert two 3 X2" ENDCAPS (12) into the ends of the UPRIGHTFRAMES(8) as shownin FIGURE
¯ Insert four GUIDERODBUSHINGS(10) into the UPRIGHTFRAMES(8) as shown in FIGURE
5

FIGURE 4
STEP 4:
¯ Insert one 1-3/4" ROUNDENDCAP(20) into the end of each HOUSING(6) as shownin FIGURE
¯Slide one 2-1/2" ODBUMPER(19) over the end of each HOUSING(6) as shownin FIGURE
¯Insert the shaft of the HOUSINGS(6) into the ends of the SMITHBAR(5) as shownin FIGURE
I 1/2 I 1/2 I 1/2 I 1/2 I 1/2
01234
6

FIGURE 5
;TEP5:
¯ Hookthe SMITHBAR(5) intothe slots ofthe UPRIGHTFRAM]ES(8).
¯CAREFULLYslide one GUIDEROD(9) fltrough the upper hole in the UPRIGHTFRAME(8). Slicte one 1" SHAFTCOLLAR(1 l)
the bottomof the GUIDEROD(9), the CAREFULLYlower the GUIDEROD(9) through the HOUSING(6) oft the SMITHt3AR(5)
into the bottomhole of the UPRIGHTFRAME(8). Repeatthis step on the other side.
¯ Slide the 1" SHAFTCOLLARS(11) up the GUIDERODS(9) to thebushing and SECURELYTIGttTEN.
7

FIGURE6
STEP 6:
Attach six 3-1/4 X1-3/4" OLI]3ES(18) to the LEFT&RIGHTSAFETYSTOPS(3 &4) as shownin FIGURE6 using
followingsteps:
¯Thoroughlycleanall surfaceswherethe 3-1/4X1-3/4"GLIDES(18)are to beattached.
¯Removethe 3-1/4X1-3/4"GLIDES(18)fromthepaperbackingandfirmlyapplythemto all shownsurfaces.
1/2 [ 1/2 [ 1/2 [ 1/2 [ 1/2 ] 1/2 [
1 2 3 4 5 6
8

FIGURE 7
STEP7:
¯ .Assemblethe LEFT&RIGHTSAFETYSTOPS(3 &4) to the UPRIGHTFRAMES(8) as showninFIGURE

FIGURE 8
STEP 8:
¯ Insert sixteen 9/16" CAPPLUGS(17) into the exposedholes inthe UPRIGHTFRAMES(8) as showninFIGURE
¯ Insert eight 7/16" CAPPLUGS(16) into the exposedholes in the UPPER&LOWERCROSSBRACES(1 &2) as sho~tin FIGURE
Thank you for purchasing the Parabody 888101 SMITHMACHINE.If unsure of proper use of equipment,
call your local Parabody distributor or call the Parabody customer service department at [phone].
10