ParaBody 908101 ST User manual

.~erious Steel
908101 ST LAT MACHINE
II I
ASSEMBLY INSTRUCTIONS
Part # 6677801 1Revision: 02/24/97

[IMPORTANTNOTES
I
There is a risk assumedby individuals whouse this type of equipment. To rnin,imize risk, please
follow these rules:
1. Consult your physician before beginning any exercise program.
2. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so mayresult in serious injury.
3. Donot allow minors or children to play on or around this equipment.
4. Exercise with care to avoid injury.
5. If unsure of proper use of equipment, call your loeal Parabodydistributor or call the
Parabody customer service department at [phone].
Please note:
* Thankyou for purchasing the Parabody 908101STLat Machine. Please, ~ r,ead these
instructions thoroughly and keep them for furore reference. This product nust be assembled
on a flat, level surface to assure its proper function.
* Werecommendcleaning your product (pads and frame) on a regular basis’,, using warmsoap.v
water. Touch-up paint can be purchased from your Parabody customer service representative.
at [phone].
[Tools Requiredfor Assembly[
*Rubber mallet or hammer
* 3/4" wrench
* 9/16" wrench
* Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* Tape measure
[Bolt LengthRuler
NOTE: BOLTLENG’rTH IS MEASUREDFROMTHE UNDERSIDEOF THE E~EADOF THE BOLT.
/////
BOLT LENGTHRULER:
[ 1/2 [ 1/2 ¯[ la [ 1/2 [ 1/2 [ 1/2 [
4 $ 6
0I I [ , ’ ’ [ , , .L

[ PARTSLIST
KEY
1
2
3
4
5
6
7
8
9
I0
11
12
13
14
PART # DESCRIPTION
BENCH FRAME6671803
6673703 TOP BOOM
KNEE SUPPORT
6672202
6674103 UPRIGHT
6674402 FOOT SUPPORT
6(~72703 ’" ~OWER
6674603 TOWER BRACE
6z~89902 PLATE,1/4 X2 X7-1/~
6621001 CI2iROME LAT BAR
6678201 DOUBLE D CHROME HANDLE
6671601 ’121-3/4" (:ABLE ASSY
6671001 117-1/4" (:ABLE ASSY
3116101 ~i..1/2;’ PULLEY
3116201 3-I/2" PULLEY
QTY KEY
115
1 16
I 17
1 18
119
120
121
2 22
123
124
126
3 27
428
PART # DESCRIPTION
6637102 SE,~
6676802 KN~ PAD
3102917 1/2 X 4" BOLT
3102910 1/2’ ’X 3’" BOLT
3102~22 3/8 X 2-3/4" BOLT
3102902 3/8 X 2-1/4" BOLT
3102924 3/8 X 1-3/4"BOLT
3102502 1/~ " WASHER
3102501 3/8" WASHER
3 I02801 I/2" LOCKNUT
3102802 3/8" LOCKNUT
6480301 3/8" FLAN SPACER
6412001 3/8" SPR/NGPIN
3103801 5/16" $1~ i? HOOK
QTY
1
2
12’
2
8
2
4
12
12
13
8
I0
1
2
STEP1:
Securely attach the TOWERBRACE(7)
TOWER(6) using two 1/2 X 4" BOLTS(17),
two 1/2" WASHERS(22), and two 1/2" LOCK
NUTS(24) as shownin. FIGURE
STEP2:
Loosely attach TOWER(6) to BENCHFRAME
(1) using two 1/2 X4" BOLTS(I7), two
WASHERS(22), and two 1/2" LOCKNUTS(24)
as shownin FIGURE1.
1/2 X4"
3

FIGURE 2
1/2 X4"
1/2 X4"
STEP3:
Loosely attach UPRIGHT(4) to BENCHFRAME(1) using four 1/2 X 4" BOLTS(17),
WASHERS(22), and fi3ur 1/2" LOCKNUTS(24) as shownin FIGURE 1/2"
FIGURE 3
STEP 4:
Securely attach four 3-1/2" PULLEYS(14) to the TOPBOOM(2) using four 3/8 2-3/4" BOLTS (19),
eight 3/8" FLANGESPACERS(26), and four 3/8" LOCKNUTS(25) as shown in FIGURE
2345 60 1 I I I I I I I [ I I I [ I I.L.,[ I__l
4

1/2 X4"
FIGURE 4
1/2 X4"
STEP5:
A. Loosely attach TOPBOOM(2) to TOWER(6) and UPRIGHT(4) using 1/2 X4" BOLTS (17),
four 1/2" WASHERS(22), and three 1/2" LOCKNUTS(24) as shownin FIGURE
B. Securelytighten all loose frameconnectionsmadeto this point.
FIGURE 5
1/2 X3"
3/8 X2-3/4"t
STEP6:
A. Securely attach FOOTSUPPORT(5) to the BENCHFRAME(1) using two 1/2 X 3" BOLTS(18),
two 1/2" WASHERS(22), and two 1/2" LOCKN~TS(24) as shownin FIGURE
B. Securely attach SEATPAD(15) to the BENCHFRAME(1) using two 3/8 X 2-3/4" BOLTS(19)
two 3/8" WASHERS(23) as shown in FIGURE

FIGURE 6
STEP7:
A. Securely attach two KNEEPADS(16) to KNEESUPPORT(3) using four 3/8 IX 1-3/4" BOLTS
and four 3/8" WASHERS(23). See FIGURE
B. Slide KNEESUPPORT(3) over square tube on BENCHFRAME(1). Makesure SPRING
HOUSINGon the K~NEESUPPORT(3) is facing away from the SEATPAD.See FIGURE6 &
STEP8:
Securely thread 3/8" SPPd[NGPIN(27) to the
SPRING PIN HOUSINGon the KNEESUP-
PORT(3) as shownin FIGURE
FIGURE 7
45 62 3 I I I I [ I 1.1_] I__1
0[ I I I
I I

STEP9:
Assembletwo 7-1/4" PLATES(8) to two 4-1/2" PULLEYS
(13) using two 3/8 X 2-1/4" BOLTS(20), four
WASHERS(23), and two 3/8" LOCKNUTS(25).
FIGURE8.
FIGURE
FIGURE 9
STEP10:
Securely assemble one 4-1/2" PULLEY(13) to the UPRIGHT(4) using two 3/8 X2,-3/4" BOLTS(19),
two 3/8" FLANGESPACERS(26), two 3/8" WASHERS(23), and two 3/8" LOCKNUTS(25).
FIGURE9.
THIS CONCLUDESTHE ASSEMBLYOF THE 908101. PLEASE REFERTO THE 912101 OR
913101 INSTRUCTIOHS ON HOWTO ASSEMBLETIlE WEIGHT OPTION.