ParaBody 805106 Installation guide

I
Serious
805106 FLAT & INCLINE BENCH
ASSEMBLY INSTRUCTIONS
Part# 6706601 1Re~’ision:09111/97

IIMPO~~ANT~OTESl
WELCOMETO THE WORLDOF g,,iou,S’,eee:
Please note:
* Thank you for purchasing the Parabody 805106 FLAT& INCLINEBENCH.Please rea~
these instructions thoroughly and keep themfor future, reference. This product must be
assembledon a flat, level surface to assure its proper function.
* Werecommendcleaning your product (pads and frame) on a regular basis, using warmsoapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
There is a risk assumedby individuals whouse this type of equipment. To minimizerisk, please
follow these rules:
1. Inspect equipmentdaily. Tighten all loose connections and replace wornparts immediately.
Failure to do so mayresult in serious injury.
2. Donot allow minors or children to play on or around this equipment.
3. Exercise with. care to avoid injury.
4. If unsure of proper use of equipment,call your local Parabodydistributor or call the
Parabody customer service department at [phone].
ToolsRequiredfor Assembly[
* 3/4" wrench
* 9/16" wrench
*Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* Tape measure
Bolt LengthRuler
NOTE: BOLTLENGTHIS MEASUREDFROMTHE UNDERSIDEOF THE HEADOF THE BOLT.
BOLT LENGTHRULER:
,11iiiii!1
BOLT LENGTH
3 4 [ I I I
0 1 I ! I ! , ! I I I !
I I I I I I

FIGURE3
I !
1/2 X3"
3/8
STEP 3:
¯ Snap two 3 X 2" GUIDEINSERTS(15) into the ends ofthe WOLFFSLEEVE(7) =~s-shown in HGURE
¯In~er~ 3/8" SPRINGPIN ASSEMBLY(11) into the spring pin barrel on WOLFFSLEEVE(7) and tighten
securely. See FIGURE3.
¯Slide one 4" VINYLCAP(17) over the U-PIN(16) as shownin FIGURE
¯Slide U-PIN(16) through the bushing on WOLFFSLI~.Wv-E(7) and attach with PAL-NUT
¯Slide the WOLFFSLEEVE(7) over the BENCHFRAME(3).
¯Securely assemble the BENCHFRAME(3) to the REARLEG(1) &the SWIVELPLATE(2) using two
3" BOLTS(21), two 1/2" FLATWAS~(24), and two 1/2" NYLOCKNUTS(26) as shown in FIGURE
¯ Securely assemble the 2 SQ.X18" TUBE(8) to the BENCHFRAME(3) using two 3/8 X3" BOLTS(19),
3/8" FLATWASI-~I~S(23), and two 3/8" NYLOCKNUTS(25). See FIGURE3.
3 [ I I I
1 [ ! ! ! !
0 I ! I I
I ! I ! ! ! I ! I
4

PARTSLIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
PART#DESCRIPTION
6706303 REAR LEG
SWIVEL PLATE
6706203
6705703
6681902
6624202
6624302
6623702
BENCH FRAM~
1/4 X 2 X 16-1/2" PLATE
LEFT BACK PAD ANGLE
RIGHT BACK PAD ANGLE
WOLFF SLEEVE
6236503 2 SQ. X18"TUBE
6706002 BACKPAD
6705802
6412001
6692601
6406401
SEAT PAD
3/8" SPRING PIN ASSEMBLY
3 X2" END CAP
HINGE TAB
QTY KEY
114
115
116
217
118
1 19
120
121
122
123
124
125
226
27
PART #DESCRIPTION
6467001 "PARABODY" LOGO END CAP
6590801 3 X 2" GUIDEINSERT
6619301. U-PIN
3118401 4" VINYL CAP
3102909 3/8 X1¯ BOLT
3102904 3/8 X3¯ BOLT
3202101 1/2 X 1-1/4" BOLT
3102910 1/2 X 3¯ BOLT
3202107 1/2 X6-1/2" BOLT
3102501 3/8 ¯ FLAT WASHER
3102502 1/2" FLAT WASHER
3102802 3/8" NYLOCKNUT
3102801 1/2" NYLOCKNUT
3109602 PAL NUT
QTY
-4
2
1
1
6
2
2
2
1
10
4
2
5
1
STEP1:
¯Insert one 3 X2" ENDCAP(12) into top of the
REARLEG(1) as shownin FIGURE
¯Slide two "PARABODY"LOGOENDCAPS(14)
over the ends of the REARLEG(1). SeeFIGURE
FIGU~ 1C~"
STEP2:
¯Slide two "PARABODY"LOGOENDCAPS(14)
over the ends of the 2 SQ.X18" TUBE(8). See
FIGURE2.
FIGURE

,N/I-I X rdI ~.. ,N/T-IX~/I
¢ X’IflDIzl

* All connections use one 3/8 X 1" BOLT(18) and one 3/8" FLATWASHER(23)
FIGURE 6
STEP 6:
¯Securely fasten the BACKPAD(9) to the LEFT(5) and RIGHT(6) BACKPADANGLESusing four 3/8
BOLTS(18) and four 3/8" FLATWASHERS(23) as shown in FIGURE
¯Securely fasten the SEATPAD(10) to the HINGETABS(13) using two 3/8 1"BOLTS (18) and two 3/8"
FLATWASHERS(23) as shown in FIGURE
¯Securelytighten the four connectionsonthe 1/4 X2 X16-1/2" PLATES(4), then backnuts off 1/4 of a turn
until the BACKPAD(9) adjusts easily.
THIS CONCLUDES ~ ASSEMBLY OF THE 805106 FLAT & INCLINE BENCH
,, I,,,I,,,l,,,I,,, ¯ "