ParaBody 832102 User manual

832102 LEG PRESS
Part # 6763901
Rev.A Version: 832102 Revision: 06/27/01
1
ASSEMBLY INSTRUCTIONS

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the Parabody 832102 LEG PRESS. Please read these instructions
thoroughly and keep them for future reference. This product must be assembled on a flat,
level surface to assure its proper function.
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* 5/32” Allen wrench
* Tape measure
2
NOTE:BOLTLENGTHIS MEASURED FROMTHEUNDERSIDEOFTHEHEAD OFTHE BOLT.
BOLT LENGTH RULER:
We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
BoltLengthRuler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
WELCOME TO THE WORLD OF Serious steel!
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].
BOLT LENGTH
5. Consult a physician before beginning any exercise program.

3
PARTS LIST
PART #
6574503
6573603
6655701
6575403
6573903
6476403
6575102
6597402
6574001
3103102
3116201
6177001
6405201
6416601
6467001
6500601
3102501
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
QTY
1
1
1
1
2
1
1
2
2
2
1
8
14
1
2
2
8
PART #
3102601
3102802
3102807
3102801
3102804
3102941
3102922
3102904
3102935
3102918
3202107
6122703
6020601
3104901
3106803
6412001
DESCRIPTION
3/8” LOCK WASHER
3/8” LOCK NUT
3/8” LOW HEIGHT LOCK NUT
1/2” LOCK NUT
1/2” LOW HEIGHT LOCK NUT
3/8 X 1-1/2” BOLT
3/8 X 2-3/4” BOLT
3/8 X 3” BOLT
3/8 X 4-1/2” BOLT
1/2 X 3-1/4” BOLT
1/2 X 6-1/2” BOLT
3/8 ID X 3/8” SPACER
1/2” FLANGE BEARING
3/4” FLANGE BEARING
5/16” SET SCREW
3/8” SPRING PIN
QTY
4
2
1
2
2
2
2
2
1
2
2
2
8
4
4
1
DESCRIPTION
BASEFRAME
SEATFRAME
REARTUBE
FOOTPLATE
LEVERTUBE
HANDLE
ADJUSTMENTTUBE
SEATPAD
3/4 X 8-1/4” SHAFT
1 X 8” GRIP
3-1/2” PULLEY
2-1/2 X 5-1/2” NON-SKID STRIP
2” SQ. END CAP
PARAGLIDE (QTY. 8)
2” SQ. COVER CAP
2” WHEEL
3/8” FLATWASHER
KEY
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33

4
FIGURE 1
STEP 1:
• SECURELY assemble the REAR TUBE (3) to the BASE FRAME (1) using two 3/8 X 3” BOLTS (25), four 3/8” FLAT WASHERS
(17), and two 3/8” LOCK NUTS (19). See FIGURE 1.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Attach two 2” SQ. COVER CAPS (15) onto the ends of the REAR TUBE (3) as shown in FIGURE 1.
• Insert four 2” SQ. ENDCAPS (13) into the ends of the BASE FRAME (1) as shown in FIGURE 1.
3/8 X 3” 25
13
1
15
19
17
3

FIGURE 2
STEP 2:
• SECURELY assemble one 3/8” SPRING PIN (33) to the spring pin barrel on the SEAT FRAME (2) as shown in FIGURE 2.
• Insert two 2” SQ. ENDCAPS (13) into the ends of the SEAT FRAME (2) as shown in FIGURE 2.
2
13
33
14
• Attach four PARAGLIDE STRIPS (14) to the inside of the SEAT FRAME (2) using the following steps:
• Thoroughly clean all surfaces where the PARAGLIDE STRIPS (14) are to be attached.
• Remove the PARAGLIDE STRIPS (14) from the paper backing and firmly apply them to all shown surfaces.
5

6
STEP 3:
FIGURE 3
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Attach four PARAGLIDE STRIPS (14) to the outside of the ADJUSTMENT TUBE (7) using the following steps:
• Thoroughly clean all surfaces where the PARAGLIDE STRIPS (14) are to be attached.
• Remove the PARAGLIDE STRIPS (14) from the paper backing and firmly apply them to all shown surfaces.
• SECURELY assemble one 3-1/2” PULLEY (11), two 2” WHEELS (16), two 3/8” FLAT WASHERS (17), and two 3/8 ID X 3/8”
SPACERS (29) to the ADJUSTMENT TUBE (7) using one 3/8 X 4-1/2” BOLT (26) and one LOW HEIGHT LOCK NUT (20)
as shown in FIGURE 3.
3/8 X 4-1/2” 26
3/8” LOW HEIGHT 20
17
16
29
11
14
7

7
STEP 4:
FIGURE 4
• CAREFULLEY slide the ADJUSTMENT TUBE (7) over into the SEAT FRAME (2) and engage the SPRING PIN into one of
the adjustment holes. See FIGURE 4.
7
2
SPRING PIN
FIGURE 5
STEP 5:
• Insert two 3/4” FLANGE BEARINGS (31)
into each of the two LEVER TUBES (5) as
shown in FIGURE 5.
31
5
31
5

8
STEP 6:
FIGURE 6
17
5
5/16” SET SCREW 32
0123456
1/2 1/2 1/2 1/2 1/2 1/2
1
9
• SECURELY assemble the LEVER TUBES (5) to the BASE FRAME (1) using two 3/4” SHAFTS (9) and SECURE in place
using four 5/16” SET SCREWS (32). See FIGURE 6.
• Insert four 2” SQ. END CAPS (13) into the ends of two LEVER TUBES (5) as shown in FIGURE 6.

9
STEP7:
FIGURE 7
1
30
5
4
13
• Insert four 2” SQ. END CAPS (13) into the ends of FOOT PLATE (4) as shown in FIGURE 7.
• Insert eight 1/2” FLANGE BEARING (30) into the LEVER TUBES (5) as shown in FIGURE 7.

10
FIGURE 8
STEP 8:
• SECURELY assemble the FOOT PLATE (4) to the LEVER TUBES (5) using two 1/2 X 6-1/2” BOLTS (28) and two 1/2” LOW
HEIGHT LOCK NUTS (22) as shown in FIGURE 8.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
1/2” LOW HEIGHT 22
28 1/2 X 6-1/2”
5
12
4
• CAREFULLY attach eight NON-SKID STRIPS (12) to the FOOT PLATE (4) as shown in FIGURE 8.