Paradox DGP2-641 User guide

LCD Keypad
DGP2-641
System Manager’s Manual
System Manager’s ManualSystem Manager’s Manual
System Manager’s Manual
Also includes
Operating Instructions

TABLE OF CONTENTS
INTRODUCT ION ........................................................... 3
Legend .......................................................................................... 3
BASIC OPERATION ..................................................... 3
Auditory F eedback (B eep Tones) ........... ... ... .. ... ... .. ... ... ... .. ... ... .. .. 3
Confidentia l Mode ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... .. 4
Partitione d System .. ...... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... .... 4
Area Sta tus Display .... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... .. 4
ARMING ........................................................................ 4
Exit Delay Tim er ..... ...... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... .... 4
Regula r Arm ing.. ..... ...... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... .... 4
Stay Arming . ... ... .. ... ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ...... .. ... ... .. .. 5
Instant Arming ... .. ... ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .. .. 5
Force Arming .. ... .. ... ... ... .. ... ..... ... ... .. ... ... .. ... ... .. ... ... .. ... ... ..... ... ... .. .. 5
Bypass Progr amm ing .... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... .... 5
One -Touch B uttons .... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... .. 6
Keyswitc h Arming .. ...... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... .... 6
Auto-Arming ........... ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .. .. 6
DISARMING .................................................................. 6
Entry Delay Timer ... ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .... 6
Disarm ing an Ar med S ystem ..... ... .. ...... .. ... ... .. ... ... .. ... ... ... .. ... ... .. .. 7
Alar m M emory Display ..... ... .. ... ... .. ... ... .. ... ... ..... ... .. ... ... ... .. ... ... .. .. 7
ACCESS CODES .......................................................... 7
System Master Code (Default 123456)........................................ 7
Find Ne xt F ree User ... ..... ...... ..... ... ..... ..... ...... ..... ..... ...... ..... ...... .... 8
Copy User Options ..... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .. .. 8
Use r Labels... ...... ..... ...... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... .... 8
Dele ting Use r Acce ss C odes . ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... .. 9
Programm ing User Ac cess Codes . ..... ..... ...... ..... ..... ...... ..... ...... .. 10
Use r Options. ...... ..... ...... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... .. 12
Access Contr ol User Options ..... ..... ...... ..... ..... ........ ...... ..... ...... .. 12
USING ACCESS CONTROL....................................... 13
Entering & Exiting .. ... ... .. ...... .. ... ... .. ... ... .. ... ... .. ... ... .. ...... ... .. ... ... .. 13
Arming and Disarm ing with C ard . .. ...... .. ... ... .. ... ... .. ... ... ... .. ... ... .. 13
How Ac cess Control Works.... ...... ..... ..... ...... ..... ..... ...... ..... ...... .. 14
TROUBLE DISPLAY ................................................... 15
Event Record Display ... ..... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ...... ... .. ... ... .. 16
ADDITIONAL FEATURES........................................... 16
Programm able Outputs ( PGMs) . ..... ...... ..... ..... ...... ..... ...... ..... ..... 16
Keypa d Settings ... ...... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... 16
Set Time & Date . ..... ...... ..... ........ ..... ...... ..... ..... ...... ..... ...... ..... ..... 17
Programm ing C hime Zone s .. ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... 17
Panic Alarms ... ... .. ... ... ... .. ... ... .. ... ... .. ... ..... ... ... .. ... ... .. ... ... ... .. ... ... .. 17
Quick F unction Buttons ..... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .. 17
TESTING AND MAINTENANCE ................................. 18
Burgla r Alarm Testing .... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... 18
Fire Alarm Testing .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .. 18
System M aintenance .. ..... ...... .. ...... ..... ..... ...... ..... ..... ...... ..... ...... .. 18
System Test ..... ... .. ... ... ... ..... ... .. ... ... .. ... ... .. ... ... .. ... ... ..... ... ... .. ... ... .. 18
FIRE AND BURGLAR A LARMS................................. 18
Standa rd Fire Zone . ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... .... 18
Dela ye d Fire Zone .. ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... .... 19
Fire S afety Tips ...... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... ..... .... 19
Minim izing Home Fir e Haza rds..... ..... ...... ..... ..... ...... ..... ...... ..... . 20
Hom e F ire W arning System ... ..... ...... ..... ..... ...... ..... ...... ..... ..... .... 20
Burgla r Alarm . ..... ...... ..... ..... ...... ..... ..... ...... ..... ..... ...... ..... ...... ..... . 20
VOICE-ASSISTED ARM/DISARM MODULE
21
INTRODUCT ION ......................................................... 21
ACCESS CODES ........................................................ 21
HOW DO I USE IT? ..................................................... 21
THINGS YOU SHOULD KNOW.................................. 21
Whe n Accessing your InTouch... ... ..... ...... ..... ..... ...... ..... ...... ..... . 21
When Arming or Disar ming.. . ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .. ... . 21
Whe n Activating or De activating a PGM ... ... ..... ...... ..... ...... ..... . 21
When Using your Intouch... ... ... .. ... ... .. ... ... .. ... ... .. ... ... ... .. ... ... .. ... . 22
TELEPHONE BUTTON FEATURES........................... 22
INTOUCH EXAMPLE .................................................. 22
INTOUCH SYSTEM CHECKL IST ............................... 23
APPENDIX 1: HEBREW SPECIAL CHARA CTERS... 24
APPENDIX 2: RUSSIAN SPECIAL CH ARACT ERS .. 25
INDEX.......................................................................... 26

LCD Keypad 3
1.0 INTRODUCTION
Your DigiplexNE Sab otage-Proof High-S ecurity S ystem i s an advanced technology secur ity system tha t will provide
you with reliab le security protection an d powerful features that a re ea sy to use. The ele gant and user-frien dly LCD
keypa d will allow you easy access to your security system's functions and information at the touch of a button. The
32-character LCD screen will display messages and menus to guide you through the system’s operations. Your
Installer can even customize the me ssages for your ho me or business.
Since you will communicate your in structions to your system throug h the keypad, please read this manua l car efully
and have your Installer explain basic system operation.
If you have the InTouch Voice Assisted Arm/Disarm Module (APR3-ADM2) connected to your DigiplexNE system,
please refer to page 2 1 for op erating instructions.
1.1 LEGEND
Indicates a warning or an important note.
Indicates u seful in formation or a tip.
[SQUARE BRA CKETS] In dicates in formation that must be entere d on the keypad.
2.0 BASIC OPERATION
The follo wing sections will in troduce you to the roles o f the buttons, lights, a nd messages on your LCD keypad.
Figure 2.1: Basic Overview
2.1 AUDITORY FEEDBACK (BEEP TONES)
Wh en you en ter information o n the keypad, the keypad will g uide you with beep ton es to commun icate the
acceptance or r ejection of yo ur entries.
Confirmation Beep: When a n op eration (i.e. arming /di sarming) is successfully entered or when the system
switches to a new status/mode, the keypad emits an intermittent beep tone (“BEEP-B EEP-BEEP-BEEP -BEEP”).
The LCD screen will guide you
with detailed messages.
Use the arrow buttons to scroll
through the current menu when
the arrows appear in the LCD
screen.
ACTION BUTTONS:
Each button’s function is explained in the following sections of the manual.
“ STATU S” LIGHT:
When Green:
ON = All zones are closed.
OFF = One or more zones are open.
FLASH = Exit Delay
When Red:
ON = Area(s) armed
OFF = Area(s) disarmed
FLASH = System in Alarm
“AC” LIGHT:
ON = AC power
OFF = Power failure
[CLEAR]= Erases current data entry
or reverts to the preceding step.
[ENTER] = Saves current data and
exits current menu.

4 User’s M anu al
Rejection Beep: Whe n the system reverts to a previous status, o r wh en an ope ration is in correctly en tered, the
keypa d e mits a continuou s be ep tone (“BEEEEEEEEEEP”).
2. 2 CON FIDEN TIAL MODE
Your Installer can program keypads to not display th e status o f your system automatically by chang ing the LCD
scree n to Confidential Mode . In Confidential Mod e:
• The zones and status messages will NOT be displayed
• The indicator lights will NOT illuminate
• Depending on how your keypad was programmed by your installer, you must either press a button or enter your User
Access Code to illuminate the indicator lights and activate Normal Mode.
2.3 PARTITIONED SYSTEM
A sepa rated system is called a Partitioned System, which can be useful in situation s wher e shared security systems
are more pra ctical. Your installer can de sig n your system to recogn ize u p to eig ht sepa rate protected area s. For
example, a company that h as both an office area an d a wareh ouse area can arm and disarm ea ch area separately
and control the access to e ach area .
If you ha ve access to mor e than o ne a rea, an d you ne ed to select a specific area(s) whe n pro mpted by you r LCD
keypa d, follow eithe r o ne of the followi ng three methods to make yo ur selection:
• Press the keypad button corresponding to the area you wish to select (i.e. 1, 2,...8).
• Press the
[0] button for all areas.
• Use the
[ S
SS
S ] and [ T
TT
T ] buttons, and press [ ENTER ] when the area you want to select appears on the scre en.
2.4 AREA STATUS DISPLAY
In Area Status Display mod e, the following information will scroll on the LCD scree n:
•“read y”: if all zones in the selected area are closed.
•“not ready”: if zones in the selected area are open.
• open zones within that area (i.e. “Front Door Open”).
•“Trouble(s)”: (section 7.0 on page 15) if a trouble has occurred.
• “Alarms in Memory”: (section 4.3 on page 7) if an alarm has occurred.
• “Armed” ; “Force Armed” ; “Instant Armed” ; “Stay Armed”: displays the arming status of the selected area.
3.0 ARMING
Wh en your system is armed, it can re spond to any bre ach in the protected zone s by causing an alarm an d se nding
a report to your Cen tral Monitorin g Station.
3.1 EXIT DELAY TIMER
Wh en you arm your system, i t will trigger the E xit Delay Timer to provid e you with e noug h time to exit the pr otected
area before the system is armed.
The Area Status Display
allows you to view the status
of the selected area s in a
Partitioned System (Refer to
section 2.3 on pa ge 4).
How do I see the status of the areas?
1) Enter your [AC CESS CODE], and then press the [1] button.
2) Press th e b utton corr espond ing to the are a (i .e. 1, 2,...8), o r u se the [S
SS
S] and
[T
TT
T]buttons an d p ress [ENTER]when the area you want to view appe ars o n
the screen.
3) Press [CLEAR]to exit.

LCD Keypad 5
3. 2 R EG ULAR AR MING
3. 3 S TAY AR MING
3.4 INSTANT AR MING
3.5 FORCE ARMING
3.6 BYPASS PROGRAMMING
A zon e’s area must be d isarmed befor e the zon e can b e bypassed.
Fire Zones cannot be bypassed.
This method is used for the
everyday a rming of your
system. All zones within the
protected area must be
close d to Regular arm the
system.
How do I Regular arm the system?
1) Enter your [AC CESS CODE].
2) Press th e [ARM]button.
3) If you have access to more than on e area , select the area(s) you wish to
Regular arm (refer to section 2.3 on page 4).
Stay armin g will partially arm
you r system to permit you to
remain in you r home or office
by armin g th e o uter zones
(perime ter) of the p rotected
area (i.e. d oors and
windows).
How do I Stay arm?
1) E nte r yo ur [ACCESS CODE].
2) Press the [STAY]button.
3) If you have access to more than on e area , select the area(s) you wish to
Stay arm (re fer to section 2.3 on page 4).
Thi s featur e is th e same as
Stay arming except that there
is no Entry Delay. Therefore,
any armed zone that is
breache d will i mmediately
generate a n alarm.
How do I Instant arm?
1) E nte r yo ur [ACCESS CODE].
2) Press the [5] bu tton .
3) If you have access to more than on e area , select the area(s) you wish to
Instant arm (re fer to section 2.3 on page 4) .
For ce arming all ows you to
quickly arm your system
whe n zon es are open.
Howe ver, once the ope n zone
is closed, your system will
then a rm tha t zone as well.
How do I Force arm?
1) E nte r yo ur [ACCESS CODE].
2) Press the [FORCE]button.
3) If you have access to more than on e area , select the area(s) you wish to
Force arm (refer to se ction 2.3 o n p age 4).
You can bypass certain zones
whe n you arm the protected
area(s). When a zone is
bypassed, it will be ignored
the next time your system is
armed. Once your area is
disarmed, the system will
unbypass the zon e.
How do I Bypass a zone?
1) E nte r yo ur [ACCESS CODE].
2) Press the [BYP]button.
3) Ente r the zone n umber (i.e. 01, 0 2,...9 6), or use the [S
SS
S]and [T
TT
T]buttons an d
press [BYP] once the zone you want to bypass a ppea rs o n the screen. If
“bypa ssed” do es no t appe ar on the screen and the keypad emits a Reje ction
Beep, you ma y not have access to bypass that zone.
4) Repe at step 3 until all zones you want to bypass have been selected.
5) Press the [ENTER]button to save and e xit.

6 User’s M anu al
3.6.1 BYPASS RECALL
3.7 ONE- TOUCH BUTT ONS
If en able d b y your Installe r, you can access the following feature s without using your User Access Code by pressing
and holding the desire d One -To uch button.
3. 8 KE YSWITCH AR MING
A key can be used to ar m an d disarm your system using two forms of keyswitches. With a Maintained Keyswitch,
place the key in the “ON” position to ar m your system, and place the key in the “OFF” positi on to disarm your
system. With a Momentary Keyswitch, place the key in the “O N” po sition briefly then place it back in the “OFF”
position to arm the system. Re peat this pro cess to d isarm wi th a Momentary Ke yswitch.
3.9 AUT O-ARMING
If enabled by your Installer, you can set the time that a n area will arm itself au tomatically.
3.9.1 TIM ED A UTO-ARMING
3.9.2 NOMOVEM EN T AUTO-ARMING
Your system can be p rogr ammed to send a rep ort to your Cen tra l Monitorin g Station a nd/or arm the system if there
is no activity in the a rea d uring a specified period of time. Your installer can set No Movement Auto-Armin g to
function in either Regula r o r Stay arming mod e.
4.0 DISARMING
Wh en your system is disar med, it deactivates any a larms in p rogre ss, and it deactivate s the zones so the alarm wi ll
not be triggered if zones are br eached .
Bypass Recall reinstates the
zon es that were bypassed the
last time your system was
armed.
How do I activate Bypass Recall?
1) E nte r yo ur [ACCESS CODE].
2) Press the [BYP] butto n.
3) Press the [MEM ]button.
Zone s bypassed the last time your system was ar med are bypa ssed.
4) Press the [ENTER]button to save and e xit.
BUTTON FEATURE BUTTON FEATURE
[ARM]Regular arm [DIS ARM ]Disarm a Stay/Instant a rmed are a
[STA Y]Stay arm [5] Instant arm
[FORCE]Force arm [6] Chan ge displa y settin gs
[BY P]Bypass Programming [7] Vie w Ev en t R ec ord di sp lay
Your installer can set Timed
Auto-Ar ming to function in
either Fo rce o r Stay arming
mode. A sixty-second Exit
Del ay sequen ce will beg in
prior to your system
automatically arming itself at
the programmed time .
How do I set the Auto-Arming timer?
1) E nte r yo ur [ACCESS CODE].
2) Press the [0] button .
3) Press the [MEM]button.
4) If you have access to more than on e area , pre ss the area ’s number, or use
the [S
SS
S]and [T
TT
T]buttons and press the [AC C] button when th e a rea you want
to progr am appears on the scree n.
5) Enter the time you want the area to be arme d a ccording to the 24- hour clock
(i.e. 9 a.m. is 09:00 and 9 p.m. is 21:0 0).
6) Press the [ENTER] button to save and e xit.

LCD Keypad 7
4.1 ENTRY DELAY TIMER
Your installer will program designated entry po ints (i.e . the front doo r) with an Entry Dela y Timer. This dela y gives
you time to enter the armed pre mises and enter your code to disarm your system before the ala rm is trigge red.
4.2 DISARMING AN ARMED SYSTEM
In the case of a burglar alarm, leave the premises and call the Police f rom a sa fe place.
4.3 ALARM MEMORY DISPLAY
5.0 ACCESS CODES
Access Codes allow access to the system. Your system supports up to 999 User Access Codes. Codes are given a
User Number between 00 2 and 99 9 (User Nu mber 001 is the System Master Code) . Your In staller wi ll progr am
User A ccess Codes to be four, six, or var iable s of one to six digi ts in length. Each d igit can be any valu e between
zer o and nine. If your Installer programmed your system to a ccep t a var iable code length, you have to press the
[ENTER] button after enterin g your User A ccess Code.
5.1 SYSTEM MASTER CODE (Default 123456)
The System Master Code will
give you access to all the
features availa ble on your
system, as well as the ability
to ad d, modify, o r dele te any
User Ac ce ss C o des. We
sug gest tha t you chan ge this
code to prevent others from
accessing and cha nging
options without a uth orization . Your In staller can set The System Master Code to b e either 4 or 6 dig its in length.
The System Maste r Code has access to all Access Control Doors and all Acc ess Control
features a t a ll times. Only the c ard’s serial num ber and t he choice of arming method can be
changed. If the other options are manually changed, the System Master Code will immediately
revert to its original programming.
You can assign a lab el (name) to a User A ccess Code at any p oint duri ng th e “prog ramming
User Access Code” process. Refer to section 5.4 on page 8 to a ssign a User Label.
You can only d isarm an are a
to wh ich yo ur Us er A c ce ss
Code is assigned. User
Access Codes with the “Arm
Only” (section 5.7 o n pag e
12) option ena bled cannot
disarm an armed system.
How do I disarm the system?
1) E nte r yo ur [ACCESS CODE].
2) Press the [DISARM]button.
If you have access to more than on e area , select the area(s) you wish to
disar m (refer to section 2.3 o n page 4 ).
How do I disarm a system in alarm?
1) E nte r yo ur [ACCESS CODE].
2) In the case of a false a larm, call your Central Monitorin g Station qu ickly to
advise them of the false alar m.
Your system will recor d all the
alarms that occurred durin g
the last armed p eriod . The
zones in ala rm will remain in
the Alarm Memory until the
next time that area is armed.
How do I view the list of alarms that occurred?
Whe n an alar m has occurre d, the LCD scre en will display “Alarms in Memory
[MEM ] to View”.
1) Press the [MEM]button. Each zone that was brea ch ed while ar med will
appear below “Alarm in:”.
2) Press the [CLEAR]button to exit the Ala rm Memory Displa y.
How do I change the System Master Code?
1) Enter the Curren t [ACCESS COD E](default: 12 3456 ).
2) Press the [0] button.
3) Press the [AC C]button.
4) Enter the numbe rs [0 ] [ 0] and [1 ].
5) Enter a [NEW CODE].
6) Press the [ENTER]button to save and exit.

8 User’s M anu al
5. 2 FIND N EXT FREE USE R
5.3 COPY USER OPTIONS
5. 4 U SER L AB ELS
5.4.1 KE YPAD BUTTONS
Every nu meric b utton on you r LCD keyp ad is assigne d a set o f letters. To obtain the desired lette r usin g the nu meric
buttons on you r keypad, p ress the bu tton un til the desired letter app ears on the screen. For example, if you wanted
to enter the lette r “C” you would pr ess the [1]button three times (refer to Table 1 on page 8). If using a Hebr ew
keypa d, re fer to Table 4 in Ap pend ix 1 : Heb rew Spe cial Characters on pa ge 24. If using a Russian keypad, refer to
Table 6 in Appe ndix 2: Russian Special Char acters on pa ge 25.
Table 1: Keypad Letter Assignments
Thi s feature automatically
searches your system for the
next avai lable unassigned
User Access Code.
How do I find the next free user?
1) Enter your [AC CESS CODE](System Master Code or User Access Code with
Master feature).
2) Press th e [0] button, and then the [ACC]button.
3) Press th e [BYP]b utt on .
4) Program the User Access Code as d etailed in Figure 5.1 o n pa ge 10 starting
from step 5.
Thi s fea ture al lows yo u to
copy the User Options,
Access Control Options, and
Area Assignments from one
User Access Code to another.
All User O ptions ar e copied
except the User Code, Card
Assignment, an d User L abel .
How do I copy user options?
1) Enter your [AC CESS CODE] (System Master Code or User Access Code with
Master feature).
2) Press th e [0] button, and then the [ACC]button.
3) Enter the 3-digit User Numb er yo u wish to copy TO.
4) Press th e [MEM ]button.
5) Enter the 3-digit User Numb er you wish to copy FROM.
6) Enter a User Code. If the User Code is o f variab le leng th, press th e [EN TER]
button after enterin g the User Code . If necessary, assign an Access card
(step 10 in Figur e 5 .1 o n p age 10 ) a nd User Labe l (section 5.4 on page 8).
7) Press [ENTE R]to save and exit.
User l abel s p ersona lize User
Access Codes and ca n b e
assigned by pre ssing [ENTER]
at any point after step 4
during the pro gramming of
User A ccess Codes (Figure
5.1 on page 10) . For
Example, the LCD ke ypa d
can display “John Smith
Select Action”.
How do I program a user label?
At any point after step 4 in Figu re 5.1 o n page 1 0:
1) Press th e [ENTER]b utton .
2) Type the desir ed characters as d etailed in section 5.4.1 on page 8 a nd
section 5.4.2 on page 9.
3) Press th e [S
SS
S]button to move the cursor to a new space.
4) Repe at steps 2 a nd 3 until the desired la bel is co mplete.
5) Press th e [ENTER]button to save and exit.
Ke y Pre ss Ke y
Once
Pre ss Ke y
Tw ice
Pre ss Ke y
Th r e e Ti m es
[1] ABC
[2] DEF
[3] GH I
[4] JKL
[5] MNO
[6] PQR
[7] STU
[8] VW X
[9] YZ

LCD Keypad 9
5.4.2 SPECIAL FUNCTION KEYS
[STAY] =Insert Space
Pressing the [STAY ]key i nserts a bla nk space in the curren t cursor po sition .
[FORCE] = Delete
Pressing the [FO R CE ] ke y will delete the character o r b lank space found at the current cursor position.
[ARM] =Delete Until the End
Pressing the [ARM] key will delete all characters an d spaces to the righ t o f the cursor and at the cursor's
position.
[DISARM]= Numeric Keys / Alp hanu meric K eys
Every time the [DISARM]key is p ressed it will toggle from numeric keys to alphanumeric keys a nd vice
versa. Numeric: Keys [0] to [9]represent n umber s 0 to 9.
[BYP] =Lower Case / Uppe r Case
Every time the [ BYP]key is p ressed i t will togg le the case setting from lo wer to upper case and vice ve rsa.
[ME M] = Special Cha racters
After pr essi ng the [MEM]key, th e cursor will turn into a flashing black square . Usin g Table 2 o n pa ge 9,
enter the 3-d igit numbe r that rep resents the desired symbol. If using a Hebrew keypad, re fer to Table 5 in
Appendix 1: Hebr ew S pecial Chara cters on page 24. If using a Russian keypad, refer to Ta ble 7 in
Appendix 2: Russian S pecial Characters o n p age 25 .
Ta ble 2: Special Characters Catalogue
5.5 DELETING USER ACCESS CODES
To delete User Access Cod es, follow steps 1 to 5 in Figur e 5.1 on pa ge 10 , bu t pre ss the [CL EAR ]button in Step 5.
Once the information is erased , pre ss th e [ENTER ]b utton to save a nd exit.

10 User’s Manual
5.6 PROGRAMMING USER ACCESS CODES
The System Master and Users with the Master feature can program User Access Codes with User Options and
Area Assignments. Figu re 5.1 on page 10 describ es the steps you would foll ow to prog ram User Access Codes. If
you wish to program User Access Codes using the NEware Software, please contact your Installer for information.
If the keypad emits a Rejection Be ep at any point during the pr ogra mmin g proced ure, yo u ma y have chosen an
existing User Cod e or you d o not have access to certain User Option s ( section 5.7) and A rea A ssignments ( step 7
in Fig ure 5.1 on p age 10 ). User ’s with the Maste r feature can onl y assign User Options and Ar ea Assignments that
they are assigne d to. For e xample, i f a User with the Master fe ature is a ssigned User O ption 1 and Are a 2, they can
only a ssig n O ptions 1 and A rea 2 to a User Access Cod e.
Figure 5.1: Programming User Access Codes
Enter your [ACCESS CODE](System Master Code or User Access Code with Master
feature).
Press [0] to enter the Programming Menu.
From Programming Menu, press [ACC].
Enter the 3-digit User Number you want to program; press the [T
TT
T]button to scroll the
list of codes and then press [ACC]once the desired code appears on the screen; or to
“Find Next Free User” press the [BYP]button (refer to section 5.2 on page 8).
Enter a User Code within the brackets. If the User Code is of variable length, press the
[ENTER]button after entering the User Code. Press the [S
SS
S]button to reach the User
Options screen.
NOTE: The User Code is a Personal Identification Number (P.I.N.).
Program the User Options by pressing the number on your keypad corresponding to the
User Option you wish to enable. The option is considered ON when the number
appears within the brackets. Proceed to step 7 by pressing the [S
SS
S]button. For a
detailed description of the User Options refer to section 5.7 on page 12.
Options [1] and [2] : Master Feature
[1] OFF = Master Feature disabled.
[1] ON, [2] OFF = User Can create and modify
User Access Codes and User labels only.
[1] ON, [2] ON = User has full Master rights.
User c an c reate, modify, and program User
options, User Access Options and Area
Assignments.
Option [3]: Duress
Option [4]: Bypass
Option [5]: Arm Only
Option [6]: Stay and Instant Arm
Option [7]: Force Arm
Option [8]:OFF - Access keypad’s
partitions only
ON - Acc ess any
partition assigned to user

LCD Keypad 11
Users are able to perform actions (arming, disarming, etc.) only in the area(s) they are
assigned. To assign an area(s) to a User Access Code, enter the number corresponding
to the area you wish to assign (i.e. [1] = area 1, ...[8] = area 8).
Press the [T
TT
T]button to return to the User Options; press the [S
SS
S]button to proceed to
step 8; or press the [ENTER]button to save and exit programming mode.
NOTE: If no area is assigned, and if PGMs are programmed by your Installer, the User
can only control the PGMs. Refer to section 8.1 on page 16 for a more detailed
explanation of PGMs.
A) Enter the 2-digit Access Level (i.e. 00, 01,...15) within the first set of brackets.
An Access Level determines which Access Control Doors a User is allowed to pass
through. There are 16 possible Access Levels which are usually programmed by your
Installer. If you wish to program the Access Levels yourself, you will need the NEware
Software which is available through your Installer. Access to all Access Control Doors is
Access Level 00.
B) Enter the 2-digit Schedule (i.e. 00, 01,...15) in the second set of brackets.
Schedules, programmed by your Installer, determine the hours, days, and holidays that
Users are permitted through Access Control Doors. Each user is assigned a Schedule
through the User Access Code. To provide access at all times, assign Schedule 00.
Program the Access Control User Options by pressing the number on your keypad that
corresponds to the Option you wish to assign. The option is considered ON when the
number appears within the brackets. For a detailed description of the User Access
Control Options, refer to section 5.8 on page 12. Press the [S
SS
S]button to proceed to step
10.
Option [1]: Access Card is Activated
Option [2]: Can Disarm with Access Card
Option [3]: Extended Unlocked Period
Options [4] and [5]: Arming with Card
[4] ON, [5] OFF = Regular Arm
[4] OFF, [5] ON = Stay Arm
[4] and [5] ON = Force Arm
[4] and [5] OFF = Disable the Arming with Card feature
Option [6]: Add Tolerance Window to Schedule
Option [7]: Code Follows Schedule
Option [8]: Card to Unlock and Code to Disarm
Enter the Access Control Card’s serial number within the brackets on the screen by
either using the keypad buttons, or presenting the card to the keypad’s reader.
Press the [ENTER]button to save and exit.

12 User’s Manual
5.7 USER OPTIONS
Options [1] and [2]: Master Featur e
Wh en option [1] i s OFF, the User canno t program other Users i nto the system.
Wh en option [1] is ONan d option [2] is OFF, the User can p rogr am a nd modify User Access Codes (P.I.N. onl y) and
User La bels.
Wh en both op tions [1] and [2] are ON, the User h as Ful l Ma ster rig hts. The User can cre ate or modify User Access
Codes, User Options, User Access Con trol O ptions, Access Ca rd Numbers, User La bels and Are a Assignments
according to th eir own pro gramming. For exampl e, if the Full Master User has access to area #1 an d option [4]
(Bypass) only, the Full Master User can only assign area #1 and option [4] to other Users in the system.
Option [3]: Duress
Wh en op tio n [3 ] is ON, th e Duress feature is en able d. Thi s feature is u sed when some one forces a User to ar m or
disarm an are a(s). B y e ntering a User Access Code (P.I.N.) reser ved fo r the Du ress feature, the system will ar m o r
disarm the a rea(s), and then send a sile nt alarm to the Central Monito ring Station.
Option [4]: B ypass
Wh en option [4] is ON, the Bypass feature is e nable d. This fea ture allows the User to d eactivate zones when arming
the ar ea(s).
Option [5]: Arm Only
Wh en option [5] is ON, the Ar m On ly feature is enable d. The User can arm assigned ar eas with either a card or
code, bu t cann ot di sarm. When the op tion is OFF, the User can either arm or d isa rm assigned are as.
Option [6]: Stay & Instant A rm
Wh en op tio n [6 ] is ON, the Stay and Instant Arm features are enabled. The User can no w Stay or In stant Arm thei r
assigned are as.
Option [7]: Force Arm
Wh en option [7] i s ON, the Force ar m feature is ena bled . The User can now Force a rm the ir assigned areas.
Option [8]: Area Access
Wh en option [8] is ON, the keypad will p ermit a ccess to all th e areas assigned to the User Access Cod e. When
option [8] is OFF, the keypad will only pe rmit access to the areas it controls. For example, the keypad is assigned
area 1 only, a nd your User Access Cod e i s assigned areas 1 to 8. If the o ption is ON, you can access all eig ht are as
from the keypad. If the o ption is O FF, you can only a ccess area 1.
By default al l Users ca n Regula r arm the system.
5.8 ACCESS CONTROL USER OPTIONS
Option [1]: Access Card is Activated
Wh en option [1] is ON, the Access Control Card is activate d a nd can be used whe n A ccess Con trol is enabled in the
system. When the option is OFF, the Access Contro l Ca rd cannot be used.
Option [2]: Can Disarm with Access Card
Wh en option [2] i s ON, a User’s Access Control Card can unlock and disarm an armed Access Control Door. When
o ption [2 ] is OFF, follow the settings in option [8] on page 13.
For option [2] to function in the ON position, option [5] “Arm Only” in the User Options must
be disabled (refer to section 5.7 on page 12).
Option [3]: Ca rd with Extended Unlocked Period
Wh en optio n [3] is ON, “Extended Unlocked Pe riod ” is enab led. “Extended Unl ocked Period” refers to th e time
period programmed into each Access Co ntrol Door by your Installer that extend s the unl ocked time of the door. Fo r
example, if you r Installer sets the Unlocked per iod of the doo r to 30 seconds and the E xten ded Unlo cke d Perio d to
15 seconds, a User Access Code with “Extended Unlocked Pe riod ” enab led will ha ve a total of 45 seconds to pass
thro ugh the do or.

LCD Keypad 13
Options [4] and [5]: Arming with Card
Options 4 and 5 de fine the type of arming when a rming with a n Access Control Card (r efer to section 6.2.1 on page
13). You can either Reg ular ar m, Stay arm, Fo rce arm, or Disable the Ar ming with Car d feature.
[4] ON, [5 ] OFF = Regular Arm
[4] OFF, [5] ON = Stay Arm
[4] and [5] ON = Fo rce Arm
[4] and [5] OFF = Disable the Armin g with Card fea ture
Option [6]: A dd Tolerance Windo w to Sched ule
Wh en option [6] is ON, the Sched ule Tolerance Win dow fea tu re i s enab led. Th is feature extends a User’s sche duled
access period thro ugh an Access Control Door by the amount p rogrammed by your Installer. For e xample, if the
User ’s a ssigned sched ule for the door is Mo nday to Frida y fro m 9:00 a.m. to 5:00 p.m., and your Insta ller sets the
“Tolerance Window” at on e hou r, the User with the “Schedule Tolerance Wind ow” ena bled will b e abl e to enter and
exit one hour before a nd after their scheduled time for that door.
Option [7]: Co de Follows Schedu le
Wh en option [7] is ON, Users can use their A ccess Code s o nly dur ing their sche dule d hou rs assigned in step 8 in
Fig ure 5.1 on pag e 10. Wh en the option is OFF, Users can use their Access Codes at any time.
Option [8]: Card to Unlock and Code to Disarm
O ption [8 ] fu nc tio ns o nly if o pt ion [2 ] in se ction 5. 8 is OFF. W he n o ption [8 ] is ON, a User can use an Access Control
Card to unlock an armed Access Control Door, however the User must enter a User Access Code to disarm the
armed area. Whe n option [8] i s OFF, a User can gain a ccess to an Access Control Door only if the d oor ’s area(s) is
already disa rmed.
For option [8] to function in the ON position, option [5] “Arm Only” in the User Options must
be disabled (refer to section 5.7 on page 12).
6.0 USING ACCESS CONTROL
6.1 ENTERING & EXITING
Depend ing on ho w your system is i nstalled, there are vario us ways to en ter and exit Access Control Doors:
1)Present you r Access Control Card to the re ader. The system will verify that the
card is allowed access according to its assigned Access Le vel a nd Sche dule . If it
is accepted, the system will unlock th e door. The reader ’s light can be
programmed by the installer to turn gre en or extinguish briefly to indicate that the
door can be ope ned .
2)Whe n the motion detector detects mo vement (Requ est for Exit), it will unlock the
door to permit pa ssage from in side.
3)Enter you r User A ccess Co de on the keypad and press [AC C].
4)If the Access Control Door is o n a “ Door Unlocked Sched ule” , you may be able to
open Access Control Doors without using a User Access Code or an Access
Control Car d. Dependin g o n the do or’s prog ramming, the d oor can remain
unlocked du ring the en tire pro grammed sche dule or the door can un lock once a
valid Access Con trol Ca rd is pre sented to the rea der d uring the schedule and
then will re main unlo cked for the remainder o f the schedule .
6.2 ARMING AND DISARMING WITH CARD
6.2.1 ARMING WITH CARD
An Access Contr ol Card can b e pr ogra mmed to a rm area s assigned to the d oor when i t is presented to
the read er (doo r) twice within app roximately 5 secon ds without op enin g the d oor.

14 User’s Manual
The Access Control card must be:
• presen ted to a door during its assigned Schedule (refer to step 8 in Figure 5.1 on page 10).
• presen ted to a door within its assigned Access Level (re fer to step 8 in Figure 5.1 on page 10).
• prog rammed to allow arming (options [4] a nd [5 ] in se ction 5.8 on page 12).
• assigned to all areas th at are assigned to the Access Control Do or (refer to step 7 in Figure 5.1 on p age
10), o r a ssign ed to at least one of th e areas assigned to the Acce ss Control Door dep ending on how
your Installer has prog rammed the Access Control Doo r.
6.2.2 DISARMING WITH CARD
To disa rm and unlock a n A ccess Co ntrol Do or wh en the a rea assigned to it is armed, pr esent you r Access
Control Card to the read er (doo r).
The Access Control card must be:
• presen ted to a door during its assigned Schedule (refer to step 8 in Figure 5.1 on page 10).
• presen ted to a door within its assigned Access Level (re fer to step 8 in Figure 5.1 on page 10).
• prog rammed to allow disarming (o ption [2] in section 5.8 on page 1 2).
• assigned to all areas th at are assigned to the Access Control Do or (refer to step 7 in Figure 5.1 on p age
10), o r a ssign ed to at least one of th e areas assigned to the Acce ss Control Door dep ending on how
your Installer has prog rammed the Access Control Doo r.‘
6.3 HOW ACCESS CONTROL WOR KS
To illustrate how Access Con trol fun ctions, we will u se thre e simple Access Control System examples:
Figure 6.1: Example A
Bonnie’s Access Control Card is
programmed with A ccess Level
01 and Sche dule 0 1. If she
presents her card to the rea der
on Door 02 o n Tuesday, Au gust
3 at 3 p.m., she will gain access
to the room.
Figure 6.2: Example B
If Bonnie presents he r car d to the
reader on Door 02 on S atu rday
or on a Holiday at 3 p.m., she will
be denied access.

LCD Keypad 15
Figure 6.3: Example C
If we change Bonnie’s Access
Level to 02 a nd she pre sents her
car d to the reader on Door 02 on
Tuesday, August 3 at 3 p.m., she
will be d enie d a cce ss .
7.0 TROUBLE DISPLAY
If your system experiences any
problems, “Trouble(s) [TRBL] to
View” will appear on the LCD
scree n. The Troubl e Display will
only display the troubles that
occur in th e area( s) to wh ich the
keypa d has been assigned.
Potential troub les h ave been
sorted into eig ht grou ps. O nly the tro ubles which are relevant to you are listed and describ ed below. If a trouble that is
not described or listed below appears, contact your Installer.
We strongly sugge st t hat if a ny troubles occur, contact your Installer immediate ly to hav e your
system serviced.
7.0.1 GROUP 1: SYS TEM
AC Failure
The control panel has detected a power fail ure. Thi s means that your system is r unni ng on the ba ckup
battery. If this trou ble occurs whe n your establi shment is not exp erien cing a p ower failure, call your
Installer for repairs.
Battery Trou ble
The backup ba ttery is di sconnected, needs to be recharg ed, or repla ce d.
Bell Absent
The system has detected that the bell or siren i s not conne cted.
7.0.2 GROUP 5: ZONE TAMPER
The zone(s) that was tampered with will be di splayed on the LCD scree n.
7.0.3 GROUP 6: ZONE LOW BATTERY
If a wireless device's battery need s to be rep laced, the zon e tha t is a ssigned to the device will be
displayed o n the LCD screen.
7.0.4 GROUP 7: ZONE FAU L T
A wire less device is no lon ger commu nicating with i ts receive r, or a conn ectio n or CleanMe TM trouble is
occurring with your smoke detectors.
7.0.5 GROUP 8: CLO CK LOSS
The time and date have been re se t to the default. This is the on ly trouble that we recommend that you
co rrec t . “Clock Loss [8] to Set” will app ear on the LCD scre en after you press the [TR BL ]button. Refer to
section 8.3 on p age 17 to set the time and da te.
How do I view the Trouble Display?
1) Press the [TR BL ]bu tton whe n “ Trouble(s) [TRBL] to View” appears on th e
LCD scree n. The Gr oup Head ing with the trou ble will appe ar on the screen.
2) Press the [S
SS
S]and [T
TT
T]buttons to scroll between the Groups experiencin g a
trouble.
3) Press the [NU MB ER]of th e Trouble you wish to view.

16 User’s Manual
7.1 EVENT RECORD DISPLAY
Once you ha ve entered Eve nt Record Display mode, you can cha nge the o rder tha t the Event Record scree ns
appear by pressing the [7] bu tton. If yo u alre ady know the number of the even t you want to view, pr ess the [ME M]
button after step 3 a bove, and then enter the e vent's number.
8.0 ADDITIONAL FEATURES
8.1 PROGRAMMABLE OUTPUTS (PGMS)
Your system includes Prog rammable Outputs (PG Ms) that can be pro grammed by your Installer. A PGM triggers
when a prede termined even t or series o f events occurs in your system. The PGMs can be programmed to reset
smoke ala rms, turn on light switche s, open o r close garag e door s an d mu ch mor e. A sk your Installe r abou t this
usefulfeature.
8.2 KEYPAD SETTINGS
You can modi fy the keypad settings to suit your needs (Refer to Figur e 8 .1 on p age 16 ).
1)Scro lling S peed r efers to the amount of time that a message will re main on the screen b efore moving to the next
message .
2)Backlight re fers to the illumina tion beh ind th e buttons a nd LCD screen.
3)Con trast refers to how da rk o r pa le chara cters will appe ar on the screen.
Figure 8.1: : Modifying LCD screen setting s
The Event Record Display will
record the user- initiated
actions that occurred in your
system as well as any alarms
or troubl es (i.e. “Access
Granted ”). You will o nly be
able to view the events that
occurred in the area(s)
assigned to your User Access
Code.
How do I view the Event Record?
1) Enter your [ACCESS CODE ].
2)Press the [7 ] button.
3)If you ha ve access to more than one area, select the area( s) you wish to
view (refer to section 2.3 on page 4).
4)Use the [S
SS
S]and [T
TT
T]buttons to scro ll between the events.
5)Press the [CL EAR ]b utt on t o exit.

LCD Keypad 17
8.3 SET TIME & DATE
8.4 PROGRAMMING CHIME ZONES
8.5 PANIC ALARMS
Your system can be programmed to send a n alar m to your Central Mon ito ring Station to request help from the
police, a med ical fa cility, the fire depar tmen t, or anyone you wish when you pre ss a p rede termined combination of
buttons. To generate a panic ala rm, simultaneo usly p ress a nd hold the b utton combinations displ ayed in Table 3 on
page 17. Yo ur installer can program th e alarm to b e either silent or aud ible .
Table 3: Panic Buttons
8.6 QUICK FUNCTION BUT TONS
How do I reset the time and date?
1) E nte r yo ur [ACCESS CODE] and press the [TRBL]button.
2) Press the [8] bu tton .
3) To change the time, place the cursor und er the numbe r you want to change
by using the [S
SS
S] button and e nter the time according to a 24 -hou r clo ck (i.e.
9 a.m. is 0 9:00 and 9 p .m. is 21:00 ).
4) To change the date, place the cursor u nder the nu mber you want to change
and enter the correct da te a ccord ing to year/month/day.
5) Press the [ENTER]button to save and e xit.
You can p rogr am the ke ypad
to e mit a r apid, inter mi ttent
beep tone when ever
designa ted zones are opened
or only when opened between
cer tain ho urs. These zones
are referred to as Chime
Zones. Your installer can also
program your Chime zone s to
beep upon closure.
How do I program chime zones?
1) Enter your [AC CESS CODE].
2) Press th e [9] button.
3) Press the [1 ] bu tton to chime a zo ne. Enter the nu mber correspo nding to the
zone to be chimed , or use th e
[ S
SS
S ] and [ T
TT
T ] buttons to scroll the list of zones.
Press the
[AC C]button to chime o r u nchime the zone that a ppea rs o n the
screen. Press
[ ENTER ] to save.
OR
Press the [2 ] bu tton to set the time period a chimed zone will beep . Enter the
time that the chimed zone(s) will start bee ping when ope ned (HH:MM). En te r
the time tha t the chimed zone(s) will stop beep ing when o pene d (HH:MM).
4) Press [ CLEA R ] to exit chime pro gramming.
Panic Alarm Types Buttons to be pressed and held
simultan eously
Em er gency Pan ic Pr ess & ho ld th e [1] and [3]buttons
Auxili ar y P anic Pr ess & ho ld th e [4] and [6] buttons
Fire Panic Press & hold the [7] and [9]buttons
You will only nee d to use the
Quick Functio n Buttons upo n
your Installer’s or Central
Mo nitoring Station's requ est.
Only the System Master Code
or User Access Codes with
the Master feature e nable d
will be a ble t o ac ce ss th ese
functions.
How do I access the Quick Function Buttons?
1) E nte r yo ur [ACCESS CODE]
2) Press the [0] button .
3) Press the:
[STAY]button to send a test report to the Central Monitori ng Station.
[FORCE] button to ca ll the Winload software.
[ARM] bu tton to answ er the Winload software.
[DISARM]button to cancel communication with the Winload software.

18 User’s Manual
9.0 TESTING AND MAINTENANCE
9.1 BURGLAR ALARM TESTING
Two peop le are n eede d to complete this test. On e perso n will watch the LCD scr een on the keypad while the othe r
person walks aro und the protected are as a nd op ens the zones (i.e. ope ns the doo rs and wind ows tha t are
protected, walk in the path o f the motion detectors, etc.). The LCD screen will display the open ed zones, but if a
zone does not register, contact your Installer.
9.2 FIRE ALARM TESTING
Do NOT use an ope n fla me o r b urnin g materials to test your fire detection devices. Your Installer will provid e d etails
on the best way to test your system.
9.3 SYSTEM MAINTENANCE
Under normal use your system req uire s no maintenance o th er than re gula r testing. We recommend that you r
Installer chan ge th e battery e very three years.
9.4 SYSTEM TEST
10.0 FIRE AND BURGLAR ALARMS
10.1 STANDARD FIRE ZONE
The Fire Zone may rese t itself once the problem has c leared. If it does not, simultaneously
press and hold the [CL EAR ] a nd [ENTER] buttons for two seconds.
Speak to you r Installer before
con ducting a System Test
since the system must be
programmed to respon d to
the test instructions. It is
normally recommen ded that
you conduct the system test
once a we ek, but conta ct your
Installer for instructions
concerning your particular
system.
How do I conduct the system test?
1) Call your Cen tral Mo nitoring Station to advise them that you ar e testing your
system.
2) E nte r yo ur [ACCESS CODE].
3) Press the [8] bu tton .
The system will test all its connections and can se nd a r epor t to your Central
Moni toring Station. If the system detects a problem, the Tr oubl e Displ ay will
show on the LCD screen ( Re fe r to section 7.0 on page 15). Call your Installer
for repairs if any Trou bles occur.
Dur ing a fire alarm, the bell/
sire n e mits an inter mittent
sou nd (BEEP-BEEP-BEEP) until
sile nced or r eset. If the zon e
is a Standa rd Fire Zone , your
system can immediately send
an alert to your Central
Mo nitoring Station.
How do I disarm a false alarm?
1) E nte r yo ur [ACCESS CODE] on the keypad.
2) Call you r Cen tral Monitorin g Station quickly to a dvise them of the false
alarm.