Parker D41FE User manual

Bulletin MSG11-5715-688/UK
Proportional Directional
Control Valve
Operation Manual
Series D*1FE
Pilot Operated
Design > 30
Parker Hannifin
Manufacturing Germany GmbH & Co. KG
Industrial Systems Division Europe
Gutenbergstr. 38
41564 Kaarst, Germany
Tel.: [phone]
E-mail: [e-mail]
Copyright © 2019, Parker Hannifin Corp.

2
Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED
HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY
DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and
authorized distributors provide product or system options for further investigation by users having
technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection
of the system and components and assuring that all performance, endurance, maintenance,
safety and warning requirements of the application are met. The user must analyze all aspects
of the application, follow applicable industry standards, and follow the information concerning
the product in the current product catalog and in any other materials provided from Parker or its
subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or
system options based upon data or specifications provided by the user, the user is responsible for
determining that such data and specifications are suitable and sufficient for all applications and
reasonably foreseeable uses of the components or systems.
WARNING — USER RESPONSIBILITY

Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
3Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
Chapter Page
1. Introduction 4
Ordering Code 4
Characteristics of Valve Driver 5
Name plate (main stage) 5
Block Diagram of Integral Electronics 5
Technical Data 6
2. Safety Instructions 7
Symbols 7
Marking, Name Plates 7
Work at the Valve 7
3. Important Details 7
Intended Usage 7
Common Instructions 7
Liability 7
Storage 7
4. Mounting / Installation 8
Scope of Supply 8
Mounting 8
Operation Limits 8
Pressure Fluids 8
Electrical Connection 9
Electrical Interfacing 10
5. Operating Instructions 12
Preferred Hydraulic Initial State 12
Solenoid Current Monitoring 13
ProPxD parameterizing software 13
Air Bleeding of Hydraulic System 18
Filter 18
Flushing 18
6. Trouble Shooting 19
7. Accessories / Spare Parts 19
Accessories 19
Spare Parts 19

4
Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
1. Introduction
Direct.
control
valve
D*1FE
Code Size
3 NG10 / CETOP 05
4 NG16 / CETOP 07
8 NG25 / CETOP 08
9 1) NG25 / CETOP 08
11 NG32 / CETOP 10
Function
Valve
option
Spool
position
on power
down
Command
signal
Size Seals
Flow
Electronic
option
NG06
pilot
Proportional
control
High
repeatability
Pilot
connections
D 1 F CE
Design
series
(not required
for ordering)
For details see
Catalogue HY11-3500UK
For details see
Catalogue HY11-3500UK
Code Electronic option
0 6+PE acc. EN175201-804
511+PE acc.
EN175201-804
7 6+PE + enable
Code Seals
N NBR
V FPM
H for HFC fluid
Code Inlest Drain
1 internal external
2 external external
4 internal internal
5 external internal
For details see
Catalogue
HY11-3500UK
1) For enlarged connections Ø 32 mm.
For details see
Catalogue
HY11-3500UK
Ordering Code

Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
5Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
Parker D*1FE proportional directional control valves
have an integral electronics.Different sizes, as well
as command signal options are available to achieve
an optimal adaption for different applications.
Characteristics of Valve Driver
The described integral electronic driver combines
all necessary functions for the optimal operation of
the valve. The most important features are:
• high dynamic actuator principle with special
designed electronic driver
• closed loop controlled pilot valve and main spool
• Ensured fail-safe behaviour
• constant current actuator control with overcur-
rent shutoff
• excellent properties for response sensitivity and
temperature drift
• differential input stage with various command
signal options
• diagnostic output for spool stroke/overcurrent
state
• standard central connection
• compatible to the relevant European EMC-
standards
Block Diagram of Integral Electronics
Valve option code 0 (6+PE)
Valve option code 5 (11+PE)
Valve option code 7 (6+PE with enable)
Name plate (main stage)

6
Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
Technical Data
General
Design Proportional directional control valve, pilot operated
Actuation VCD®-actuator
Size NG10 (CETOP 05)NG16 (CETOP 07)NG25 (CETOP 08) NG32 (CETOP 10)
D31 D41 D81 / D91 D111
Mounting Interface DIN 24340 / ISO 4401 / CETOP RP121 / NFPA
Mounting position unrestricted
Ambient temperature [°C] -20...+50
MTTFDvalue [years] 50
Weight [kg] 11.3 14.2 23.5 64.5
Vibration resistance [g] 10 Sinus 5...2000 Hz acc. IEC 68-2-6
10 (RMS) Random noise 20...2000 Hz acc. IEC 68-2-36
15 Shock acc. IEC 68-2-27
Hydraulic
Max. operating pressure [bar] Internal pilot drain P, A, B, X 350; T, Y 35
External pilot drain P, A, B, T, X 350; Y 35
Fluid Hydraulic oil acc. DIN 51524 ... 51535, other on request
Fluid temperature [°C] -20...+60 (NBR: -25...+60)
Viscosity permitted
recommended
[cSt]/[mm2/s]
[cSt]/[mm2/s]
20...400
30...80
Filtration ISO 4406; 18/16/13
Electrical
Duty ratio [%] 100
Protection class IP65 in accordance with EN 60529 (with correctly mounted plug-in connector)
Supply voltage / ripple [V] 22...30, ripple < 5 % eff., surge free
Current consumption max. [A] 3.5
Pre-fusing [A] 4.0 A medium lag
Input signal Code K (B) Voltage
Impedance
[V]
[kOhm]
+10...0...-10, ripple < 0.01 % eff., surge free, 0...+10 V P–>A (P–>B)
100
Code E Voltage
Impedance
[mA]
[Ohm]
+20...0...-20, ripple < 0.01 % eff., surge free, 0...+20 mA P–>B
< 250
Code S Current
Impedance
[mA]
[Ohm]
4...12...20, ripple < 0.01 % eff., surge free, 12...20 mA P–>A
< 3.6 mA = enable off, > 3.8 mA = enable on acc. NAMUR NE43
< 250
Input Capacitance typ. [nF] 1
Differential input max.
Code 0
[V] 30 for terminal D and E against PE (terminal G)
11 for terminal D and E against 0V (terminal B)
Code 5 [V] 30 for terminal 4 and 5 against PE (terminal W)
11 for terminal 4 and 5 against 0V (terminal 2)
Code 7 [V] 30 for terminal D and E against PE (terminal G)
Enable signal Code 5/7 [V] 5...30, Ri > 8 kOhm
Diagnostic signal [V] +10...0...-10 / +12.5 V, rated max. 5 mA
EMC EN 61000-6-2, EN 61000-6-4
Electrical connection
Code 0/7 6 + PE acc. EN 175201-804
Code 5 11 + PE acc. EN 175201-804
Wiring min. Code 0/7 7 x 1.0 AWG16 overall braid shield
Code 5 8 x 1.0 AWG16 overall braid shield
Wiring lenght max. [m] 50

Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
7Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
2. Safety Instructions
Please read the operation manual before instal-
lation, startup, service, repair or stocking! Paying
no attention may result in damaging the valve or
incorporated system parts.
Symbols
This manual uses symbols which have to be fol-
lowed accordingly:
Instructions with regard to the warranty
Instructions with regard to possible dam-
aging of the valve or linked system com-
ponents
Helpful additional instructions
Marking, Name Plates
Instructions applied on the valve, i.e. wiring dia-
grams and name plates, must be observed and
maintained legibly.
Work at the Valve
Workings in the area of installation, commissioning,
maintenance and repair of the valve may only be
allowed by qualified personnel.This means persons
which have, because of education, experience and
instruction, sufficient knowledge on relevant direc-
tives and approved technical rules.
3. Important Details
Intended Usage
This operation manual is valid for proportional direc-
tional control valves DFplus pilot operated series.
Any different or beyond it usage is deemed to be
as not intended. The manufacturer is not liable for
warranty claims resulting from this.
Common Instructions
We reserve the right for technical modifications of
the described product. Illustrations and drawings
within this manual are simplified representations.
Due to further development, improvement and
modification of the product the illustrations might
not match precisely with the described valve. The
technical specifications and dimensions are not
binding.No claim may resulting out of it.Copyrights
are reserved.
Liability
The manufacturer does not assume liability for
damage due to the following failures:
• incorrect mounting / installation
• improper handling
• lack of maintenance
• operation outside the specifications
Do not disassemble the valve! In case of
suspicion for a defect please contact Parker.
Storage
In case of temporary storage the valve must be
protected against contamination, atmospheric ex-
posure and mechanical damages. Each valve has
been factory tested with hydraulic oil, resulting in
protection of the core parts against corrosion. Yet
this protection is only ensured under the following
conditions:
Outdoor storage or within sea and tropical
climate will lead to corrosion and might dis-
able the valve!
Storage
period Storage requirements
12 months constant humidity < 60 % as well
as constant temperature < 25 °C
6 months varying humidity as well as
varying temperature < 35 °C

8
Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
4. Mounting / Installation
Scope of Supply
Please check immediately after receiving the valve,
if the content is matching with the specified scope
of supply. The delivery includes:
• valve
• operation manual
The central connector assembly has to be ordered
separately and is not included in the delivery.
Please check the delivery immediately after
receiving the shipment for apparent dam-
ages due to shipping. Report shipment
losses at once to the carrier, the insurance
company and the supplier!
Mounting
• Compare valve type (located on the name plate)
with part list resp. circuit diagram.
• Unrestricted mounting position.
• Verify the mounting surface for the valve. Uneve-
ness of 0.01 mm/100 mm, surface finish of 6.3
µm are tolerable values.
Keep clean valve mounting surface and work
environment!
• Remove protection plate from the valve mounting
surface
• Check the proper position of the valve ports and
the O-rings.
• Mounting bolts:
D31FE: 4 pcs. M6x40
D41FE: 2 pcs. M6x55, 4 pcs. M10x60
D81/91FE: 6 pcs. M12x75
D111FE: 6 pcs. M20x90
use property class 12.9, ISO 4762
Parker offers bolt kits:
D31FE: BK385, D41FE: BK320, D81/91FE:
BK360, D111FE: BK 386
• Tighten the bolts crisscross with the following
torque values:
D31FE: 13.2 Nm, D41FE: 13.2/63 Nm,
D81/91FE: 108 Nm, D111FE: 517 Nm
Insufficient condition of the valve mounting
surface migth create malfunction! Incorrect
mounting resp.bolt torque may result in abrupt
leakage of pressure fluid on the valve ports.
Operation Limits
The valve may be operated within the determined
limits only. Please refer to the “technical data“ sec-
tion as well as to the “characteristic curves“ in the
catalog.
Follow the environmental conditions! Unal-
lowable temperatures, shock load, aggresive
chemicals exposure, radiation exposure, il-
legal electromagnetic emissions may result
in operating trouble and may lead to failure!
Follow the operating limits listed in the
“specifications“ table!
Pressure Fluids
The following rules applies for the operation with
various pressure fluids:
This information serves for orientation and
does not substitute user tests among the
particular operating conditions. Particularly
no liabiliy for media compatibility may be
derived out of it.
Mineral oil: usable without restriction.
HFC: choose the right seal option.
For operation with the following pressure fluids
please consult Parker:
HFA oil-in-water emulsion
HFB water-in-oil emulsion
HFD unhydrous fluids (Phosphor-Ester)
For detailed information concerning pressure
fluids note VDMA-document 24317 as well as
DIN 51524 & 51502.
Special gaskets may be available depending on
the utilized fluid.
In case of insecurity please consult Parker.

Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
9Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
Electrical Connection
The electrical connection of the valve takes place
by one common cable, which is coupled to the
integrated electronic driver by a central connector
assembly.
The connection Code 0 as well as Code 7 requires
a 6 + PE female connector EN 175201-804.
The female connector has to be ordered
separately under article nr. 5004072.
A female connector with metal housing is
required! Plastic made models may create
function problems due to insufficient EMC-
characteristics.
The connecting cable has to comply to the follow-
ing specification:
Cable type control cable, flexible,
7 conductors, overall braid
shield
Cross section min. AWG16
Outer dimension 8...12 mm
Cable length max. 50 m
For cable lengths > 50 m consult Parker.
The connection cable is coupled to the female
connector by solder joints.
Skinning lengths for the connecting cable:
The connection Code 5 requires a 11 + PE female
connector EN 175201-804.
The female connector has to be ordered
separately under article nr. 5004711.
A female connector with metal housing is
required! Plastic made models may create
function problems due to insufficient EMC-
characteristics.
The connecting cable has to comply to the follow-
ing specification:
Cable type control cable, flexible,
8 conductors, overall braid
shield
Cross section min. AWG16
Outer dimension 12...15 mm
Cable length max. 50 m
For cable lengths > 50 m consult Parker.
The connection cable is coupled to the female
connector by crimp contacts.
Skinning lengths for the connecting cable:
For the workmanlike termination of the crimp
contacts the tool # 932 507-001 – supplier:
Hirschmann – is required.
Do not disconnect cable socket under tension!
The shielding has to be assembled according the
outline below:

10
Pilot Operated Proportional DC Valve
Series D*1FE
Operation Manual
Parker Hannifin Corporation
D_1FE 5715-688 UK CM 18.01.2019
Electrical Interfacing
Supply Voltage
The supply voltage for the valve has to cover the
range of 22...30 V. The residual ripple may not
exceed 5% eff.
The applied power supply must comply to the
relevant regulations (DIN EN 61558) and must
carry a CE-mark. The operating voltage for
the valve must be free of inductive surges.
Do not exceed the max. value of 30V! Non-
observance of this rule may result in perma-
nent damaging of the valve.
The increased inrush current of the valve
should be considered when selecting the
power supply. A stabilized power supply with
overcurrent limiting feature should not be
used. Due to the inrush current of the valve
the current limit circuit may respond prema-
turely and create problems during energizing
of the supply voltage.
The operation of the valve is blocked if the
supply voltage polarity is interchanged.
Each valve requires a separate pre-fuse of 4
Amp time lag.Non-observance of this instruc-
tion may create irreparable damage of valve
resp. incorporated system parts.
The backshell nut of the cable gland has to be
tighten with a suitable tool.The target value for the
tightening torque is 4 Nm. Tighten the cap nut with
a torque of approx.5 Nm after attaching the female
connector on the socket outlet.
Incomplete tightening of backshell nut resp.
cap nut may result in automatic release of the
connection as well as degradation of the
water tightness.
Follow the “instructions for use“ for instal-
lation of female connectors made by other
kind of brands!
The cable connection to the female connector
has to take place by qualified personnel! A
short between individual conductors resp. to
the connector housing , bad soldering as well
as improper shield connection may result in
malfunction and breakdown of the valve.
The mounting surface of the valve has to be
carefully tied to the earth grounded machine
frame. The earth ground wire from the valve
connecting cable as well as the cable shield
have to be tied to the protective earth termi-
nal within the control unit. It is necessary to
use a low ohmic potential connection between
control unit and machine frame to prevent
earth loops (cross section AWG 6).