Parker SciLog SciTemp Guide

1
SciLog
®
SciTemp
®
Temperature Monitor & Sensor
Installation, Operation, & Maintenance Instructions

2
(This Page Intentionally Left Blank)
Parker has a continuous policy of product development and although the Company reserves the right to change
specification, it attempts to keep customers informed of any alterations. This publication is for general information only and
customers are requested to contact our Process Filtration Sales Department for detailed information and advice on a product’s
suitability for specific applications. All products are sold subject to the company’s Standard conditions of sale.
SciLog®and SciTemp®are registered trademarks of Parker Hannifin Corporation.

3
Table of Contents:
Precautions: .....................................................................Error! Bookmark not defined.
Calibration: ...................................................................................................................... 6
Installation & Start-Up ..................................................................................................... 7
Maintenance & Cleaning: ................................................................................................ 7
Introduction: .................................................................................................................... 6
SciTemp®Temperature Sensor System Specifications:.................................................. 8
Part A: SciTemp®Temperature Sensor Hardware ....................................................... 11
1.0 Overview: ................................................................................................................ 11
2.0 Front Panel: Data Entry & Display.......................................................................... 12
3.0 Back Panel: Interface Options................................................................................. 13
4.0 Disposable Temperature Sensors:.......................................................................... 16
Part B: SciTemp™ Temperature Sensor Monitor Software.......................................... 17
1.0 Software Overview: ................................................................................................. 17
2.0 Main Menu: ............................................................................................................. 19
3.0 Custom Calibration Menu:....................................................................................... 21
4.0 SciTemp™ Temperature Sensor Printout Format ................................................... 22
5.0 Data Collection........................................................................................................ 22
5.1 SciTemp™ Temperature Sensor Data Collection Software: ................................... 24
5.2 PC HyperTerminal Settings:.................................................................................... 28
Appendix A: Sensor Performance Data........................................................................ 29

4
Precautions:
READ this manual BEFORE operating or servicing this equipment.
FOLLOW these instructions carefully.
SAVE this manual for future reference.
DO NOT allow untrained personnel to operate, clean, inspect, service or tamper with
this equipment.
ALWAYS DISCONNECT this equipment from the power source before cleaning or
performing maintenance.
CALL Parker Customer Service for parts, information and service.
WARNING
DISCONNECT ALL POWER TO THIS UNIT BEFORE INSTALLING,
SERVICING, CLEANING OR REMOVING THE FUSE. FAILURE TO DO
SO COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE.
CAUTION
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC
SENSITIVE DEVICES.
WARNING
ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THIS
EQUIPMENT. EXERCISE CARE WHEN MAKING CHECKS, TEST AND
ADJUSTMENTS THAT MUST BE MADE WITH POWER ON. FAILING TO
OBSERVE THESE PRECAUTIONS CAN RESULT IN BODILY HARM.
WARNING
FOR CONTINUED PROTECTION AGAINST SHOCK HAZARD, CONNECT
TO PROPERLY GROUNDED OUTLET ONLY. DO NOT REMOVE THE
GROUND PRONG.
CAUTION
USE ONLY CLASS 2 LISTED AC/DC POWER SUPPLIES WITH THIS
DEVICE. Parker dominick hunter # 070-017TOR, OR ITS EQUIVALENT IS
RECOMMENDED.

5
Précautions
LISEZ ce manual AVANT de faire fonctionner ou d’entretenir cet équipment.
SUIVEZ attentivement ces instructions.
CONSERVEZ ce manuel pour future référence.
NE LAISSEZ PAS du personnel non qualifié utiliser, nettoyer, inspecter, entretenir, réparer ou
manipuler cet équipement.
DÉBRANCHEZ TOUJOURS cet équipement de la source de courant avant de nettoyer ou
d’exécuter l’entretien.
APPELEZ PARKER pour pièces détachées, renseignements et entretien.
ATTENTION
DÉBRANCHEZ TOUT COURANT DE CETTE UNITÉ AVANT DE FAIRE
L’INSTALLATION, D’EFFECTUER L’ENTRETIEN, LE NETTOYAGE OU
AVANT DE RETIRER LE FUSIBLE. NE PAS OBSERVER CES
PRÉCAUTIONS RISQUERAIT DE CAUSER DES BLESSURES
CORPORELLES OU/ET D’ENDOMMAGER L’ÉQUIPEMENT.
PRUDENCE
SOYEZ PRUDENT LORSQUE VOUS MANIPULEZ DES APPAREILS
SENSIBLES À L’ÉLECTROSTATIQUE.
ATTENTION
AUTORISEZ SEULEMENT LE PERSONNEL QUALIFIÉ À ENTRETENIR
CET ÉQUIPEMENT. SOYEZ PRUDENT LROSQUE DES VÉRIFICATIONS,
TESTS ET AJUSTEMENTS DOIVENT ÊTRE EFFECTUÉS SOUS
TENSIONS. NE PAS OBSERVER CES PRÉCAUTIONS RISQUERAIT DE
CAUSER DES BLESSURES CORPORELLES.
ATTENTION
POUR ASSURER UNE PROTECTION CONTINUE CONTRE UNE
DÉCHARGE ÉLECTRIQUE, BRANCHEZ UNIQUEMENT SUR UNE PRISE
CORRECTEMENT RELIÉE Á LA TERRE. NE RETIREZ PAS LA FICHE DE
TERRE.
PRUDENCE
Utilisez uniquement la classe 2 ci alimentations AC / DC avec cet appareil.
Parker # 070-017TOR, ou SON equivalent est recommandé.

6
Introduction:
You will find the SciTemp® Temperature Sensor System easy to use. The state-of-the-art
hardware and software design of the SciTemp® Temperature Sensor and Monitor combination
allows you to measure and document the Temperature of many filtration / separation processes.
With proper maintenance, the SciTemp® Monitor will provide many years of excellent service
and performance.
Please read the following instructions carefully!
Inspections: Remove the products carefully from the shipping container. Check the contents
against the purchase order to verify that all parts are included and undamaged.
Please do the inspection now, even if the products are not used immediately. Many carriers
must receive damage claims within seven days of delivery. Please retain all packing material so
unit may be shipped safely, if necessary.
Customer Service: Parker customer service: If assistance is required, please contact us at:
Parker Hannifin Manufacturing Ltd Parker Hannifin Corporation
Bioscience Division – EMEA Bioscience Division – N.A.
Durham Road 2340 Eastman Avenue
Birtley, Co. Durham Oxnard, California, USA 93030
DH3 2SF, England toll free: 877 784 2234
phone [phone] phone: [phone]
fax [phone] fax: [phone]
email: [email protected] email: [email protected]
www.parker.com/bioprocessing www.parker.com/bioprocessing
Parker customer service personnel will be able to serve you more efficiently if you have the following
information:
Serial number and model name of the equipment
Installation procedure being used
Concise list of symptoms
List of operating procedures and conditions in use when problem arose
Calibration:
The SciTemp® Temperature Monitor is a calibrated device, and is calibrated with test
equipment that is traceable to NIST.
A Calibration Certificate is included with each unit, and has a one year expiration date.
It is highly recommended that the monitor be calibrated on an annual basis or more often if
your Metrology Department deems it necessary.
Parker provides this Calibration Service, complete with a new certificate, showing the “as
found” and “as left” data.
Contact local Parker representative.

7
Warranty
Country specific information can be found at: www.parker.com/termsandconditions
Standards:
EN 61326-1:2006, Class B
EN 6100-3-2:2006
EN 6100-3-3:1995 +A1:2001 +A2:2006
EN 61010-1 Issued: 2001/03/01
Conforms to UL STD 61010-1:2012 Ed.3+ R: 29Apr2016
Certified to: CSA STD C22.2 No 61010-1-12 Ed.3+U1:U2
Installation & Start-Up
Installation of the SciTemp® Temperature Monitor must be carried out only by trained personnel in
accordance with the relevant regulations and this operations manual.
Make sure that the technical specifications and input ratings of the SciTemp™ Temperature Sensor are
observed. See “SciTemp® Temperature Sensor Specifications”.
The protection provided by this equipment may be impaired if the SciTemp® Temperature Sensor is
used in a manner inconsistent with this manual or for purposes not specified by the manufacturer.
Maintenance & Cleaning:
The SciTemp® Temperature Monitor is maintenance free. The disposable sensors come pre-
calibrated from the factory and require no maintenance.
To remove dust, dirt and stains, the outer surfaces of the SciTemp® Temperature Monitor may
be wiped using a soft, non-fluffing cloth moistened with water. If required, you may also use a
mild detergent or 2-propanol.
The disposable sensors may be sanitized with 0.1 Molar NaOH, or 2-propanol. They may be
autoclaved, and newer units with the grey rings around the cable connector may be gamma
irradiated.

8
Hardware
Specifications – Monitor
Dimensions W: 6.0¨ (15.2 cm); Height 2.75¨ (7.0 cm); D: 5.5¨ (14.0 cm)
Weight 1.5 lb (0.69 Kg)
Enclosure Molded Plastic / Stainless Steel
Electrical
Power 100-240 V, 60/50 Hz AC Adaptor, 12 VDC, 500 ma Output,
Center positive. Use only Class 2 listed power supplies.
Battery BR2032, used for internal clock only, not user serviceable.
Sensor Choice of five sizes: Luer, 3/8" Barb, 1/2” Barb, 3/4” Tri-Clover
(TC) Sanitary and 1” Tri-Clover (‘Ladish’) Sanitary.
I/O Port - 1
‘T1 and T3’ Female Switchcraft connectors
Note: Please use care connecting the monitor end of the
sensor cable to these ports as the male cable end can be
damaged if mishandled.
I/O Port - 2 Output’ - Female DB25, four TTL outputs for alarms, four 4-20
ma Analog output signals, 18 bit resolution.
I/O Port - 3 ‘Printer / PC’ - DB9FM, RS-232 output
I/O Port - 3 ‘Serial I/O’ - Female DB9 (disabled).
I/O Port - 4 ‘12VDC 500ma’ - DC Input for AC Adaptor.
I/O Port - 5 ‘RS-485’ - 3 wire terminal block. RS-485 output (disabled).
Software
Operational Modes Temperature
Mode
Captures stored calibration from sensors, digital display of up
to two temperature sensor values, with High and Low user-
definable alarms for each.
Custom
Calibration
Mode
Used to perform custom calibrations, selecting User-
defined Calibration Temperature.
Temperature 4 – 60° C
Altitude Up to 2000 Meters
Environmental IP Rating IP20, Indoor dry environments, unit is wipe-down only
Rel.Humidity 0 – 95%
Voltage Fluctuation allowed: +/- 10%
Pollution Degree: 2

9
Specifications - Sensors
Power 5 VDC provided by SciTemp® Monitor.
Fluid Connections Choice of five sizes: Luer, 3/8” Barb, 1/2”
Barb, 3/4” Tri-Clover (TC) Sanitary and 1” Tri-
Clover (‘Ladish’) Sanitary.
Wetted Materials Polysulphone meets USP Class VI and FDA
21 CFR 177.1520, all wetted materials made
with animal-free compounds.
Sensor Type Thermistor, Epoxy coated, 2252 Ω.
Temperature Range -40 to +150° Celsius.
Accuracy +/- 0.10° Celsius in the 4.0 to 70° Celsius
range.
Resolution 0.01 ° Celsius
Sensor Microchip EPROM, Stores Sensor ID, and
Calibration Factor.
Sensor Connector & Cables Lockable and Waterproof.

10
SciDoc Documentation Software for PC
SciTemp® Temperature Sensor System Documentation Software Package
Excel spreadsheet with custom macros for data compilation. Includes Winwedge interface
software. Sent to you ready to use.
Complete process analysis with graphing of data
Real-time verification and documentation of process parameters, with Differential
Temperature calculated by the spreadsheet.
Includes graph of: Temperature vs. Time
Spreadsheet example:

11
Part A: SciTemp®Temperature
Sensor Hardware
1.0 Overview:
The SciTemp®Temperature Sensor System consists of two major components, the SciTemp®
Temperature Monitor, with its power supply, and the Disposable SciTemp®Temperature Sensor
flow cell, with its cable.
The Monitor is a small desktop package with a backlit display and seven buttons for easy
interface and menu selections. It displays up to two measured temperatures in real time in
digital format and the differential temperature. The monitor’s output signals are in both analog
and digital formats. It comes with a small 110 VAC wall adapter as a power supply.
The disposable SciTemp®Temperature Sensor flow cells utilize an epoxy coated 2252 Ω
Thermistor in a polysulphone flow cell available in five sizes: Luer, 3/8” or 1/2" hose barb, 3/4"
and 1” “Ladish” Sanitary TC connections.
All are pre-calibrated at the factory, and retain the calibration data on a small chip embedded in
the sensor body. The following information is retained and is accessed upon connection to the
sensor:
ID number (Contains Size, Lot number, Mfr Code, and Calibration date)
Calibration Factor

12
2.0 Front Panel: Data Entry & Display
The front panel consists of a user interface, which includes an alphanumeric display and a
membrane keypad to select operational modes and alarm settings. The display is a two line, 20
character, liquid crystal display (LCD). The display is backlit to allow easy viewing over a wide
range of lighting conditions.
The keypad consists of seven keys whose function does not change. These keys are used for
basic control and programming of the SciTemp®Temperature Monitor. The basic key definitions
are:
MENU Allows entry into the parameter settings menu.
ENTER Accepts the selected parameter setting.
EXIT Exits the menu, returning to the main operational screen.
SENSOR Recaptures the factory calibration settings stored on the sensor, and allows
entry into the custom calibration menu. This allows the user to custom
calibrate the sensor using NIST traceable equipment.
ON/STBY Turns the monitor on and off.
Up and Down arrows used to change parameters within the menus.
One LED is also on the front panel, on the ON/STBY key. This indicates the monitor is
connected to power.

13
3.0 Back Panel: Interface Options
The SciTemp
®
Temperature Sensor back panel provides interfacing ports for:
Disposable SciTemp
®
Temperature Sensor Sensors: Female 9 pin twist-lock,
labeled “Sensor T1, T2”.
Analog and TTL Output: Female DB25, labeled “Output”.
RS-232: Female DB9, labeled “Printer/PC”.
2
nd
RS-232: Female DB9, labeled “Serial I/O”, dedicated to Barcode Scanner for
future use.
RS-485: 3 wire terminal block, labeled “RS-485” (Disabled. Future versions will
permit
RS-485 Connectivity.)
Input power: Round male connector for AC Adapter, labeled “12 VDC/500 mA.
3.1 Sensor Ports: The disposable temperature sensors are connected to these two using
the included cables.
3.2 Output Port: Provides two 4-20 mA analog outputs (18 bit resolution) and TTL outputs
for the 4 alarms, Hi/Low for each temperature channel. TTL outputs provide a 0 / 5 VDC
control signal, carry minimal current. (See Pin out on next page.)
3.3 Printer/PC Port: The SciTemp
®
printer is connected to the SciTemp
®
Temperature
Monitor via this port. You need a printer cable to make the connection between the
printer and the SciTemp
®
Temperature Monitor, or a SciTemp
®
RS-232 cable to connect
the SciTemp
®
Temperature Monitor to your PC for data archival.
3.4 Serial I/O Port: Disabled, reserved for future use.
3.5 RS-485 Port: Disabled. Future Versions will enable connectivity via RS-485.
3.6 Power Input Jack: Connect the AC adapter here.

14
Pin Out of the DB25 female “Output” connector:
Analog Outputs are from an 18 bit resolution A/D converter:
For 4-20 ma output of Temperature at T1 (Analog 1), use pins 2 (4-20 -) and 14 (4-20 +). If
excitation is needed in the loop, connect pin 1 (Vpwr) to pin 14 (4-20 +), and connect the output
cable to pin 2 (4-20 -) and pin 15 (Gnd).
For 4-20 ma output of Temperature at T2 (Analog 2), use pins 4 (4-20 -) and 16 (4-20 +). If
excitation is needed in the loop, connect pin 3 (Vpwr) to pin 16 (4-20 +), and connect the output
cable to pin 4 (4-20 -) and pin 17 (Gnd).
The use of an end-user supplied analog loop power source is presented on the next
page:

15
TTL Outputs:
P1 Hi/Low Alarm: TTL 1 Pins 11 (Out0) and 13 (Gnd)
P2 Hi/Low Alarm: TTL 2 Pins 24 (Out1) and 13 (Gnd)
P3 Hi/Low Alarm: TTL 3 Pins 12 (Out2) and 13 (Gnd)
TM or DP Hi/Low Alarm: TTL 4 Pins 25 (Out3) and 13 (Gnd)
TTL outputs are either 0 or 5 VDC, and carry minimal current. They are for TTL inputs on a
PLC, or control of a 5 VDC electronic relay.

16
4.0 Disposable Temperature Sensors:
Connector type Max flow rate * Max pressure
Luer 1 liter/min 60 psi
3/8" Barb 8 liters/min 60 psi
1/2" Barb 17 liters/min 60 psi
3/4" TC 31 liters/min 60 psi
1” Ladish TC
60 liters/min 60 psi
*At a 1.0 psi drop across the sensor
Specifications for all SciTemp™ Temperature Sensor Flow Thru Temperature
Sensors
Material, Fluid Contact:
Natural PP, meets USP Class VI and FDA 21 CFR
177.1520 Medical Grade Polysulfone meets USP Class VI
and FDA 21CFR177.1520. All Wetted Materials are made
of Animal-Free Compounds. Compatible with Most
Sanitizing Agents such as NaOH, Hypochlorite. Sensors
can be repeatedly autoclaved.
Sensor Type: Thermistor, Epoxy Coated, 2252 ohm.
Temperature Sensor Range: -40 to +150 ° C for all sizes.
Temperature Sensor Accuracy: 0.01° C In the 4.0 to 70.0° C Range.
Temperature Sensor Resolution: 0.01° C.
Temperature Sensor Microchip: EPROM, stores Device ID & Factory Cal Data
Temperature Sensor Cleaning:
Sensors may be flushed with Alcohol, 0.1M or 0.5M NaOH,
dilute Bleach, or Formaldehyde for inline sanitization
several times. The Sensors may also be autoclaved. See
section 4.0.
Sensor Connector and Cables Lockable & Waterproof

17
Part B: SciTemp®Temperature
Sensor Monitor Software
1.0 Software Overview:
The SciTemp®Temperature Monitor digitally displays inputs from up to two disposable
SciTemp®Temperature Sensors simultaneously, and displays the Differential
Temperature.
The Main Menu allows you to change the temperature units (C or F), the high and low
analog range settings, adjust the baud rate and print time, as well as configure user-
defined Hi/Low temperature alarms for both displayed values.
The SciTemp®Temperature Monitor will also allow custom calibration of the sensors thru
the use of the “Sensor” button on the front panel.
(The remainder of this page intentionally left blank.)

18

19
2.0 Main Menu:
SUMMARY: This menu allows the setting of various parameters as they relate to your process.
Use “Menu” to scroll through the menu, the up/down arrow keys to scroll through choices, and
“Enter” to select the choice.
2.1 MAIN SCREEN: Displays both temperatures, T1 and T2 to a resolution of 0.01
2.2 TEMPERATURE UNITS: Use the up/down arrows to select between C (Celsius) and F
(Fahrenheit).
2.3 RANGE HI: Use to set the upper range limit of the Analog output signal (100% full
scale). Allowable maximums are 100.0 °C, 212.0 °F. Default = 100.0 °C.
2.4 RANGE LO: Use to set lower range limit of the Analog output signal (0.0% of full scale).
Default minimum is 0.0 regardless of scale.
2.5 SERIAL: Displays the RS-232 serial output parameters. Only the baud rate can be
changed. Available rates are 1200, 2400, 4800, 9600, 19200, 28800, 38400 and 57600.
Default = 9600
2.6 PRINT TIME: Used to set the data output interval, 1 to 60 sec. Default = 5 sec.
2.7 HI-ALARM T1: Used to set High Temperature Alarm, value should be within High and
Low Range set in 2.3 and 2.4 above. Hi-Alarms exist for both temperature outputs.
Default = 0.0 psi.
2.8 LO-ALARM T1: Used to set Low Temperature Alarm, value should be within High and
Low Range set in 2.3 and 2.4 above. Lo-Alarms exist for both temperature outputs.
Default = 0.0 psi.
2.9 SET TIME/DATE…..: Press Enter to enter this submenu, press Menu to bypass to
Factory Reset.
2.10 TIME: Use up/down arrows to set current time in 24 hour format, HH:mm, and press
Enter.
2.11 MONTH: Use up/down arrows to set current Month, and press Enter.
2.12 DAY OF MONTH: Use up/down arrows to set current Date, and press Enter.
2.13 YEAR: Use up/down arrows to set current Year, and press Enter.
2.14 FACTORY RESET: Used to restore the SciTemp®Temperature Sensor Monitor to the
factory default values. Change No to Yes using the arrow keys and press “Enter” to
reset, change No to Yes on the “Are You Sure?” screen and press “Enter” again to finish
the process.

20