Parker Sentinel User manual

Portable Purification System
User’s Manual
Sentinel™

1
| User’s Manual
Sentinel
™
This Manual informs the installer and operator about the safe installation, operation and everyday maintenance
of the Sentinel Oil Purication System (further to be abbreviated as Sentinel).
Always keep this Manual near the Sentinel.
Read this Manual carefully before putting the Sentinel into use or before carrying out any operation. Only then
can optimal safety be obtained.
Preface

| User’s Manual
Sentinel
™
2
Contents
Preface..................................................................... 1
Contents .................................................................. 2
1 Introduction
1.1 Warning ............................................................. 3
1.2 Manufacturer ..................................................... 3
1.2.1 Introduction Parker Hannin..................... 3
1.2.2 Partnership ............................................... 3
1.3 Related Documents........................................... 3
1.4 Machine-Identication....................................... 3
1.5 Applicable Legislation ....................................... 3
1.6 Copyright........................................................... 4
1.7 Liability .............................................................. 4
1.8 Responsibility .................................................... 4
2 Safety
2.1 Safety and Precautionary Symbols ................... 5
2.2 Warning Pictorials.............................................. 5
2.3 Operator ............................................................ 5
2.4 Engineer ............................................................ 5
2.5 General .............................................................. 6
2.5.1 Hazardous Materials................................. 6
3 Machine description
3.1 Introduction ....................................................... 7
3.2 Function............................................................. 7
3.2.1 Running modes ........................................ 7
3.3 Process Description .......................................... 7
3.3.1 Air Flow..................................................... 8
3.3.2 Oil Flow..................................................... 8
3.3.3 Water Flow............................................... 8
3.4 Controls ............................................................. 8
3.5 Hose Connections............................................. 8
3.6 User adjustable Set Points................................ 9
3.6.1 Moisture Level .......................................... 9
3.6.2 Temperature.............................................. 9
3.6.4 Sample Rate............................................. 9
4 Operation
4.1 Safety ............................................................. 10
4.2 Preparing for Use ............................................ 10
4.3 Starting ........................................................... 11
4.3.1 Initial Start Up......................................... 11
4.3.2 Starting ................................................... 11
4.4 Screen Option ................................................. 12
4.5 Set-Up Screen................................................. 12
4.6 Adjusting Set Points ........................................ 13
4.7 Removing from Service ................................... 13
5 Transport & Storage
5.1 Safety Precautions .......................................... 14
5.2 Transport (rolling)............................................. 14
5.3 Transport (lifting).............................................. 14
5.4 Transport (fork lift) ............................................ 14
5.5 Storage............................................................ 15
6 Maintenance
6.1 Safety precautions........................................... 15
6.2 Inspections ...................................................... 16
6.2.1 Daily Inspections .................................... 16
6.2.2 Weekly inspections................................. 16
6.2.3 Yearly inspections................................... 16
6.3 Maintenance.................................................... 16
7 Disposal
7.1 Safety precautions........................................... 17
7.2 Disposing of the Sentinel ................................ 17
7.3 Environmental aspects .................................... 17
8 Parts List .................................................................. 17
9 Troubleshooting......................................................... 18
Appendix 1
Technical Specications ....................................... 21
Appendix 2
Test Specications................................................. 22

3
| User’s Manual
Sentinel
™
1 Introduction
This chapter gives basic information about the Sentinel and the accompanying operations and maintenance
instructions.
1.1 Warning
Only qualified personnel are allowed to install, operate and maintain the Sentinel.
Safety is only ensured when you read this manual carefully before putting the Sentinel into use or before
carrying out any operation.
1.2 Manufacturer
The Sentinel is manufactured by:
Parker Hannin Corporation
Hydraulic Filter Division
16810 Fulton County Road #2
Metamora, OH 43450
Phone: [phone]
Fax: [phone]
Internet: www.parker.com/hydrauliclter
1.2.1 Introduction to Parker Hannifin
Parker Hannin is the world’s leading manufacturer of motion and control technologies and systems, providing
precision-engineered solutions for a wide variety of commercial, mobile, industrial and aerospace markets.
The company employs approximately 62,000 people in 48 countries around the world. Parker provides quality
services and products to our customers through strong, professional distribution and Technology Centers.
To meet our customer needs in motion and control, Parker provides the broadest range of products available
from any single supplier. This is supported by expertise in nine major technologies: hydraulics, pneumatics,
electromechanical, ltration, process control, uid and gas handling, sealing and shielding, climate control and
aerospace.
1.2.2 Partnership
At Parker we believe in partnership with our customers so we can provide them with solutions which help
achieve higher levels of productivity and protability by engineering the best systems for their requirements. This
means studying customer applications to nd new and better ways to create value. Not only a product supplier,
Parker also offers Value Added Services to help its customers save time and money.
1.3 Related Documents
In addition to this manual the following documents are included:
• Bill of Materials
• Vacuum Pump Manual
• Installation Drawings
• Hydraulic & Electric Schematics
1.4 Machine Identification
The machine is identied as: the Sentinel.
1.5 Applicable Legislation
Not all parts of the Sentinel comply to the directives of the EU. Therefore it is not provided with the CE
mark.

| User’s Manual
Sentinel
™
4
1.6 Copyright
Copyright Parker Hannin. All rights reserved. No part of this publication may be reproduced, stored in a
database or retrieval system, or publication in any form or in any way, electronically, mechanically, by print,
photo print, microlm or any other means without prior written permission from the manufacturer.
1.7 Limitation of Liability
UPON NOTIFICATION, SELLER WILL, AT ITS OPTION, REPAIR OR REPLACE A DEFECTIVE PRODUCT, OR
REFUND THE PURCHASE PRICE. IN NO EVENT SHALL SELLER BE LIABLE TO BUYER FOR ANY SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF, OR AS THE RESULT OF, THE
SALE, DELIVERY, NON-DELIVERY, SERVICING, USE OR LOSS OF USE OF THE PRODUCTS OR ANY PART
THEREOF, OR FOR ANY CHARGES OR EXPENSES OF ANY NATURE INCURRED WITHOUT SELLER’S
WRITTEN CONSENT, EVEN IF SELLER HAS BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR
OTHER LEGAL THEORY. IN NO EVENT SHALL SELLER’S LIABILITY UNDER ANY CLAIM MADE BY BUYER
EXCEED THE PURCHASE PRICE OF THE PRODUCTS.
• Neglecting warnings or prescriptions as shown on the Sentinel or stated in this manual.
• The use of the Sentinel for other applications or under other circumstances than stated in this manual.
• Modifying the Sentinel in any way. This includes the application of other spare parts and/or changing the
control program.
• Insufcient maintenance.
1.8 User’s Responsibility
The user, through its own analysis and testing, is solely responsible for making the nal selection of the system
and Product and assuring that all performance, endurance, maintenance, safety and warning requirements of
the application are met. The user must analyze all aspects of the application and follow applicable industry
standards and Product information. If Seller provides Product or system options, the user is responsible for
determining that such data and specications are suitable and sufcient for all applications and reasonably
foreseeable uses of the Products or systems.

5
| User’s Manual
Sentinel
™
2 Safety
This chapter describes the safety precautions with regard to the Sentinel. The safety precautions in this
manual should be respected. Deviation from the precautions can cause unacceptable risks.
2.1 Safety and Precautionary Symbols
Suggestion to carry out tasks easier.
Draws attention to potential problems.
Draws attention to damage to the Sentinel if the instructions are not carried out carefully.
Draws attention to serious injuries to the operator if the instructions are not carried out carefully.
2.2 Warning Pictorials
There are no warning pictorials attached to the Sentinel.
2.3 Operator
Only qualied operators should operate the Sentinel.
The operator has to be informed of chapters 1 through 6 of this manual before carrying out any operations on
the Sentinel.
While operating the Sentinel, the following Personal Protective Equipment (PPE) must be worn:
• protective clothing
• work shoes
• safety glasses
2.4 Engineer
All maintenance and installation activities are reserved for specially trained engineers.
The engineer has to be informed of the entire contents of this manual before carrying out any maintenance on
the Sentinel.
While performing maintenance on the Sentinel, the following Personal Protective Equipment (PPE) must be worn:
• protective clothing
• work shoes
• safety glasses
Figure 2.3 & 2.4: PPEs to be worn

| User’s Manual
Sentinel
™
6
2.5 General
The Sentinel can be operated and maintained safely if all safety precautions are observed; however, dangerous
situations can occur due to poor judgement or negligent use.
Always stay alert for dangerous situations.
Observe the following general precautions:
• Pay attention to loose clothing and hair.
• Keep your hands away from dangerous zones.
• Check the functionality of the Sentinel daily.
• Do not turn on the main switch if persons are in contact with the machine.
• Unplug before performing maintenance activities.
• Replace damaged or defective parts before putting the machine into service.
• Modications to the machine without prior approval of the manufacturer are not permitted.
• Never disassemble piping lines or components while under pressure.
The Sentinel is a powerful tool that supplies hydraulic fluid under high pressure. Be careful when using it.
In case of unexpected leakage:
• Immediately stop the complete system.
• Protect yourself (face, hands, etc.) against spraying liquid.
• Never try to stop the leak ow by covering it with your hands.
• Use absorbing paper to prevent uid from entering the environment.
• Properly dispose of all spilled uids.
2.5.1 Oil Contaminated with Hazardous Materials
If there is any possibility the oil being puried contains a solvent or materials which could be considered
hazardous, either with toxicant or ammable explosives, the Sentinel should not be used.
The Sentinel should never be used to remove volatile’s such as: diesel fuel, gasoline or other products
with low flash points, explosive in nature, or toxic. For clarification, consult your factory representative for
detailed information.

7
| User’s Manual
Sentinel
™
3.1 Introduction
Parker Hannin is responsible for the engineering and delivery of the Sentinel.
3.2 Function
Dehydration and purication of hydraulic uid.
The Sentinel is not permitted for any other purposes than those stated above.
3.2.1 Running Modes
There are three modes of operation for the Sentinel.
• Standard mode: Once started, the machine runs continuously until the moisture level reaches the set
point. When set point is achieved, the Sentinel will automatically shut down.
• Sentinel mode: Once started, the machine will power up and sample the oil. If the sample is above the
high moisture level set point, the machine remains on until the lower moisture level set point is reached.
The Sentinel will remain off until the high level set point is reached again.
• Batch mode: Once started, the machine runs one batch to the moisture level set point before
discharging. New batches are pulled in until the the inlet moisture is below the set point.
3.3 Process Description
The gure below is a schematic representation of the Sentinel.
The technical specifications can be found in Appendix 1 - ‘Technical specifications’.
3 Machine Description
This chapter describes the function, the major components, and the operation of the Sentinel.

| User’s Manual
Sentinel
™
8
3.3.1 Air Flow
Air moves through the unit as a result of the vacuum pump. Atmospheric air enters through a desiccant breather,
ows through a needle valve, into the vacuum chamber where the mass transfer of water takes place. The
saturated air then exhausts through a coalescing element, to eliminate any oil mist, before traveling through the
vacuum pump. Finally, the air is exhausted through the condensate tank where the free water falls out.
3.3.2 Oil Flow
Oil enters the back of the unit through the inlet port. The inlet control valve is energized during the lling cycle.
Once through the heater tube, the oil enters a diffuser where the maximum surface area is exposed while
minimizing oil carry over. At this point in the cycle, any water in the oil is ashed off and enters the drier air
above. The oil then falls into the sump where it is circulated back through the heater tube and vacuum chamber
until the temperature set point is reached. Once the temperature set point is reached the oil circulates in the
chamber for a period that optimizes the water removal rate and energy usage. At the end of this period, the oil is
returned via the return port on the back of the unit.
3.3.3 Water Flow
Water in the oil is transferred to the air where it is exhausted and trapped in the condensate tank. Roughly 20%
of the water is retained and 80% is exhausted via the exhaust port on the rear of the unit.
3.4 Controls
The controls for the Sentinel are located across the top of
the unit as shown. See chapter 4 “Operation” on how to
use the control panel.
A. The main power switch provides power to the unit.
B. The IQAN, a PLC control screen, is used to operate
all functions of the machine.
C. The phase selector is used when the IQAN screen
displays a phase fail fault. In this instance the phase
selector must be switched for proper operation.
3.5 Hose Connections
1. Hydraulic Outlet
2. Vacuum Exhaust
3. Hydraulic Inlet
4. Water Drain
2
3
4
1
A
B
C

9
| User’s Manual
Sentinel
™
3.6 User Adjustable Set Points
The following settings are adjustable within the IQAN:
• Moisture high limit
• Sample rate
• Moisture set point (low limit)
• Temperature
• Unit selector
3.6.1 Moisture Level
The oil moisture level is measured by a relative humidity sensor and is reported as a percentage. When
saturation is 100%, the oil contains the maximum amount of water that can be dissolved in the oil (any excess
seen is free water). The low moisture level is the lowest level that is desired. This is determined by the application
and oil in use. The lower the set point, the longer the Sentinel takes to reach this moisture level of saturation. The
high moisture level is the point at which the Sentinel mode of operation will stay on. This combination creates an
acceptable window of moisture below saturation.
The default low moisture level is 25% of saturation; The default high moisture level is 75% of saturation.
The maximum amount of water that is dissolved is dependent on the temperature and the type of oil. The
moisture level should always be maintained below saturation at all time to avoid system damage.
3.6.2 Temperature
The temperature set point is the point to which the oil is heated during the dehydration process.
The default value is 130° F
The maximum allowable temperature is oil dependent. Consult the oil specifications to avoid decrease
life or damage.
3.6.3 Sample Rate
The sample rate is the duration between sampling when the machine is set to Sentinel mode.
The default value is 120 minutes.
3.7 Auto Condensate Drain
When the auto condensate is selected from the set up screen, see section 4.6, the water collected in the
condensate tank will automatically drain when full. If the auto condensate is not selected a manual drain will be
required and the Sentinel will shut off when the condensate tank is full.
3.8 Vacuum Purge
A vacuum purge cycle runs the vacuum pump while no oil is taken into
the Sentinel. This purge cycle is preformed so that any moisture in the
vacuum pump is driven out and the integrity of the pump is maintained.
Press the left arrow key to cancel the vacuum purge.
3.9 Run Empty
The run empty cycle pumps any remaining oil out of the vacuum
chamber.

| User’s Manual
Sentinel
™
10
4.1 Safety
The Sentinel is tted with uorocarbon seals. All process uid
must be compatible with uorocarbon. Contact Parker with uid
compatibility questions.
4.2 Preparing for Use
Check that the oil in the vacuum pump is at the proper level before
operating.
1. Place the Sentinel on a at surface
2. Lock the brake on the two front wheels
3. Connect the hoses:
a. Hydraulic Outlet
b. Hydraulic Inlet
c. Water Drain
4. Plug in the power cord
Ensure proper ventilation when operating.
See the technical specication for proper power requirements.
4 Operation
This chapter describes the operation of the Sentinel.
2
2
3a
3b
3c
4

11
| User’s Manual
Sentinel
™
4.3 Starting
4.3.1 Initial Start-Up
1. Sentinel is shipped with the breakers in the off position and
must be turned on to operate.
2. NEMA L16-30P anged inlet is standard on all units. Cord set
(PN 943238) is available to order through Parker.
3. Power the system on.
4. If the “Phase Fail Alarm” is shown on the display, change the
phase switch position. Press OK, F2.
5. To set the language and to set the date & time, press the menu
button, located in the lower right hand corner of the IQAN.
Languages can be selected through the main set-up screen.
To choose language from the main screen choose preferences,
then F3 for languages.
6. English or Metric units can be selected see 4.6 Adjust Groups.
4.3.2 Starting
1. Power the system on.
2. If the “Phase Fail Alarm” is shown on the display, change the
phase switch position. Press OK, F2.
If oil remains in the system a message will be displayed reminding
the user to drain the oil before operating.
34
4
5
1
2
2

| User’s Manual
Sentinel
™
12
3. Start-up screen. Press F1 to continue.
4. After reading and agreeing to the messages, press F4 to
continue.
5. Press F1, F2, or F3 to select the desired operating mode.
Pressing the function keys a second time deselects the chosen
mode and allows for another selection to be made.
6. Press F4 to start the Sentinel. Press a second time to stop.
When stopped, the Sentinel will automatically run a purge cycle to
ensure the system is empty and that the integrity of the vacuum
pump is maintained.
4.4 Screen Option
Use the vertical arrow keys to select a screen option.
1. Run screen (default)
2. Gauge screen (see 4.3.2 for function keys use)
3. Set-up screen
4.5 Set-Up Screen
1. F1 performs a run empty function should any oil be left in the
system.
2. Pressing F2 allows for auto condensate drain to be selected.
Pressing and holding F2 drains the condensate tank.
3. F3 performs a vacuum purge function.
4. F4 allows the user to adjust the set points.
5. OK will reset the cycle counter and system timer.
3
4
6
1 432

13
| User’s Manual
Sentinel
™
4.6 Adjusting Set Points
The adjustable set points are:
• Moisture high limit
• Sample rate
• Moisture set point (low limit)
• Temperature
• Unit Selector
Use the arrow buttons to scroll through the options and press the
“OK” button when a selection has been made.
See Chapter 3 for the set points function
Press the escape key (back arrow) to return to the Set-Up Screen
1. Once the adjustable parameter is chosen, use the up and down
arrows to adjust to the desired setting, press ok to accept.
2. Press the escape key once to return to the point selection page.
4.7 Removing from Service
Make sure the Sentinel has stopped running before taking it out of
service.
1. Purge the vacuum pump from the set-up screen by pressing F3.
2. Make sure the oil is emptied from the system by pressing F1
“Run Empty” within the set-up screen.
3. Drain the condensate by pressing and holding F2 within the set-
up screen.
4. Turn off power via the main switch.
5. Disconnect the power cord from the back of the unit.
6. Disconnect all the hoses from the back of the unit.
Pressing the escape key while on the set-up screen, with the
Sentinel not running, will open the inlet valve to allow for the heater
tube to be drained.
Oil may leak from the hoses
4

| User’s Manual
Sentinel
™
14
5.1 Safety Precautions
Always check that the Sentinel is completely disconnected before
transporting and storing the Sentinel.
Do not lay the Sentinel on its side.
Never lift or transport a Sentinel that is filled with oil.
See Chapter 2 for more information and safety precautions.
5.2 Transport (rolling)
1. Disconnect the hoses.
2. Disconnect the power supply.
3. Unlock the brake on the two front wheels.
The Sentinel can now be freely rolled around.
Make sure the brakes are locked again when transportation is
done.
5.3 Transport (lifting)
1. Disconnect the hoses.
2. Disconnect the power supply.
3. Connect the hoisting gear to the four hoisting eyes.
Always use all four hoisting eyes when hoisting the Sentinel.
See Appendix 1 ‘Technical Specifications’ for information about
the weight of the Sentinel.
5.4 Transport (fork lift)
1. Disconnect the hoses.
2. Disconnect the power supply.
3. Insert the forks into the fork pockets from the front.
5 Transportation & Storage
This chapter describes how to transport and store the Sentinel.
1
1
2
3
3 3
3

15
| User’s Manual
Sentinel
™
5.4 Storage
When storing the Sentinel it must be placed in a room which complies to the following requirements:
• The room must be dry with a relative humidity of 45-75%.
• The ambient temperature of the storage area must be between -10 and 40°C for uid handling
components. In case of electronic components the storage temperature should be at least 0°C.
• The room where the machine or parts are stored must be free from dust otherwise the uid handling
components must be sealed with plastic foil.
If the Sentinel is stored for over a year, specic care is needed. Please contact Parker Hannin in case longer
storage is required. Otherwise, warranty may not be valid.
6 Maintenance
This chapter describes how to maintain the Sentinel.
6.1 Safety Precautions
Only qualified personnel should carry out maintenance procedures on the Sentinel.
Make sure the system is switched off completely and the power supply is locked before carrying out any
maintenance activities.
Make sure the system is completely depressurized before carrying out any maintenance activities.
After disconnecting any part, immediately block open ports with clean plugs to prevent dirt from
infiltrating the hydraulic system.
See Chapter 2 for more information and safety precautions.

| User’s Manual
Sentinel
™
16
6.2 Inspections
To ensure proper operation of the system, maintenance must be
carried out on a regular basis.
6.2.1 Daily Inspection
Vacuum oil level.
6.2.2 Weekly Inspections
6.2.3 Yearly Inspections
Only qualified personnel should carry out the yearly inspection.
Items Inspection Activities
1 System operation Check system operation - no unusual noise and
vibrations.
2 Air breather Check the breather. Normal color will be blue. If
the color is pink, the desiccant is saturated with
moisture and needs to be changed.
3 Oil filters Check the filter element condition indicator. If
needed, change the filter element.
Items Inspection Activities
Hoses Check the overall quality of the hoses.
6.3 Maintenance
To ensure proper operation of the system maintenance must be
carried out on a regular basis.
Maintain hydraulic filter according to the ∆P indicator.
(PN 936711Q)
Replace all coalescing filters after 300 hours of use.
(PN 943237)
2
A
3
3
A
B
B
Fill Port

17
| User’s Manual
Sentinel
™
7.1 Safety Precautions
Switch off the Sentinel completely before disposing of the Sentinel.
Always check that the Sentinel is disconnected from its power sources before disposing of the Sentinel.
See Chapter 2 for more information and safety precautions.
7.2 Disposing of the Sentinel
When disposing of the Sentinel, always consult Parker Hannin.
Only qualified personnel is authorized to dispose of the Sentinel.
7.3 Environmental Aspects
Please observe the following environmental aspects:
• Dispose of the Sentinel according to the legal and local regulations.
• Re-use parts and substances of the Sentinel and process parts and substances in an environmentally-
friendly manner if re-use is impossible.
• Discharge harmful, dangerous and possibly contaminated substances (or liquids) according to the legal
and local regulations.
Make sure the Sentinel is disposed of in a safe way and according to the environmental rules in the
country of use.
7 Disposal
This chapter describes how to dispose of the Sentinel.
8 Parts List
Part Number Description
00424 Float Switch
06F20C2218A1FPH80 Condensate Drain Valve
20072409 IQAN MD3 display module
2820008 Pressure Sensor
3349116565 Gear Pump
40CN205QEVE2GS164 Filter
7221GBN51V00N0D300C2 Inlet valve
7221GBN51V00N0D300C2 Recirculation valve
936711Q Hydraulic Particulate Element
943236 Mounting Bracket Kit
943237 Service Kit (includes TriCep-
tor air breather, hydraulic
particulate element, coalesc-
ing element, vacuum pump
exhaust element, vacuum
pump oil)
943238 Cordset (pigtail end)
used with 943116 and
943213 only
Part Number Description
B-10235-0-230 Heater 230VAC
B-10235-0-380 Heater 380VAC
B-10235-0-460 Heater 460VAC
CEM3546T Hydraulic Pump Motor
MPS-V33N-PGAT Vacuum Sensor
MS1504 Moisture Sensor
For Service Requiring No Yellow Metals
Part Number Description
945302 No Yellow Metals Accessory
Kit - wetted components
only (includes below part
numbers)
15U29-00V Inlet Valve
12F22C6148A3FPH80 Recirculation Valve
12F-C12L-1/3-SS Check Valve
F800S Flow Control Valve

| User’s Manual
Sentinel
™
18
9 Troubleshooting
9.1 Safety Precautions
Always wear the prescribed personal protective equipment while working with the Sentinel.
Indicates the alarm will cause an automatic shut down.
See Chapter 2 for more information and safety precautions.
Alarm Image Problem Cause Solution
Unit fails to
run from IQAN
screen
Mode not selected Choose mode of operation before pressing “On/Off”.
Phase Fail Are you out of phase?
High Sump See “Oil in Sump” warning.
Vacuum Overow See “High Oil Level” warning.
High Ambient Temp See “High Ambient Temp” warning.
Low Flow Inlet obstructed or
pinched hose
Straighten or replace. Check any ltration placed
before the Sentinel for blockage. Check all isolation
valves.
Inlet Valve Check solenoid on the inlet valve to make sure it is
functioning.
Low vacuum level,
should be greater than
22 in/HG (558 mm)
Check vacuum pump for proper operation.
Check for leaks by shutting off oil inlet valve, closing
air inlet valve to vacuum chamber, manually operate
unit until vacuum gage reads 25 in/HG, and then
stop unit. If vacuum holds for less than 30 sec then
a leak is present. If 22 in Hg cannot be achieved
and no leak is detected then check the vacuum
pump for proper function adjust or replace parts as
required.
Check needle valve, adjust for altitude.
Improper PVS installa-
tion, negative head too
high for unit
Check specication sheet. Maximum negative
suction head is 8 ft. (2438 mm). Increase inlet hose
diameter and shorten hose length to reduce line
pressure loss. Preheat oil to reduce viscosity.
Use of quick discon-
nect on inlet hose.
Quick disconnects are not recommended. Replace
with standard “full port” valve or increase size of
quick disconnect to 1.5 times the diameter of inlet
hose or consult factory for other options.
High Oil Level Inlet control valve not
closing
Check inlet control valve for debris caught in the
diaphragm. If problem persists, install a suction filter.
Middle oat switch
stuck closed
Check oat switch in vacuum chamber.
Air inlet needle valve
closed
Check needle valve and adjust if necessary.
A low flow alarm will be displayed if the
Sentinel does not take in fluid at a rate
quick enough to operate properly

19
| User’s Manual
Sentinel
™
Alarm Image Problem Cause Solution
High Sump
Alarm
Foaming oil in vacuum
chamber
High inlet moisture
Transportation
Be sure intake is full submerged.
Some oils will foam under normal operating condi-
tions. Lower vacuum level by opening air bleed valve
slowly until vacuum reaches 23 in/HG (584 mm).
Lower temperature set point.
Further maintenance:
If the sump is full a warning screen will be displayed
and the light on the gauge screen titled “High Sump”
will appear red.
1) Drain sump via the port located on the bottom
2) Change coalescing lter.
3) Check vacuum pump oil. It should be clear if not
change oil and replace vacuum pump coalescing lter.
4) Conrm the vacuum chamber overow switch is
functioning by removing the vacuum chamber cover
and exercising the oat switch, watch for the “Vacuum
Chamber Overow” alarm to be display. If the switch
works then oil entered the sump because the Sentinel
was placed on its side or the oil was allowed to foam.
High level oat switch
failure
Check high level switch in vacuum chamber.
High Level
Condensate
Alarm
Condensate tank full Drain condensate tank or turn on automatic drain
function.
Float switch faulty Check for stuck or broken switch. Repair or replace
by removing from the back side of the condensate
tank.
Fast Fill Alarm Excessive pressure on
the inlet
Restrict inlet line.
Oil left in system Run empty before starting.
Over Pressure
Alarm
The pressure in the re-
turn line exceeds 60psi
Minimize pressure losses in return hose.
Maintenance
Screen Dis-
played
The Sentinel has
exceeded its mainte-
nance timer interval
Change lters.
High Ambient
Temperature
Warning
High temperature
inside cabinet
Reset the thermostat, which is located under the
top door, by pressing the button in the middle.
Other actions include:
1. Remove doors
2. Install fan
3. Insure proper ventilation