Partner OT-200 User manual

OT-200
User Manual

i
Copyright
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of PARTNER Tech Corp.
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no


revise this publication and to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark recognition
All product names used in this manual are the properties of their respective owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to

expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device was tested for handheld operations with the device contacted directly to the human body.
To maintain compliance with FCC RF exposure compliance requirements,avoid direct contact
to the transmitting antenna during transmitting.
Declaration of conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

ii
Revision history
Version 1.0, July 2010
About this manual
This manual is intended for system administrators who are familiar with setting up a new system and
installing programs.
The manual consists of the following sections:
Chapter 1 Getting Started: This section covers unpacking and checking the
package contents, identifying components, charging the
battery, installing the MicroSD card, and powering on
the device.
Chapter 2 Using The Device: This section provides information on how to use the
device features.
Chapter 3 Using The Accessories: This section provides information on how to use the
accessories.
Appendix: The appendix covers troubleshooting, information
on having the OT-200 serviced and technical

Safety information
Before installing and using the OT-200, take note of the following precautions:
SAR compliance for body-worn operations requires at least 2 cm of separation between the device and
the user’s body
Request service for damaged products: Turn off the product, unplug it from the electrical outlet, and
request service from a service partner under the following conditions:
 The power cord or plug is damaged.
 Liquid has been spilled into the product.
 An object has fallen into the product.
 The product has been exposed to rain or water.
 The product has been dropped or damaged.
 The product does not operate normally when you follow the operating instructions.
Avoid hot areas: The product should be placed away from heat sources such as radiators, heat registers,

Allow the product to cool: Allow the product to cool before removing covers and touching internal
components.
Avoid wet areas: Never use the product in a wet location.
Avoid inserting objects into product: Never insert objects of any kind into slots or other openings in the
product.
Clean the product properly: Unplug the product from the wall outlet before cleaning it. Do not use liquid
cleaners or aerosol cleaners. Use a soft cloth dampened with water for cleaning exterior components, but
NEVER apply water directly to the product or to an LCD screen.

iii
Use the product with approved equipment: Use your product only with the computers and accessories

Adjust the volume: Turn down the volume before using headphones or other audio devices.
When device will not be used for a long period of time, please remove the battery, and store both device
and battery in a cool, dark, and dry place. For storage over a long period of time, please place product
in a dry box.
SAR compliance for body-worn operations requires at least 2 cm of separation between the device and
the user’s body.
Battery Handling Precaution
 Do not attempt to disassemble or reconstruct the packs. The battery has integrated protection circuits
and safety functions to avoid danger. If battery is damaged, it may rupture, generate heat, or cause smoke

 Do not short circuit battery. Neither short connect the positive terminal and negative terminal with
metals, nor carry or store the battery with metal objects. If the battery is short circuited, excessive large

metals. Please cover the plug with waterproof cap when not using the battery.
 Do not incinerate or heat the battery. This will cause the insulator to melt, damage the gas release vent,
and cause loss of safety function, or electrolyte ignition. Above mentioned matters will cause battery to

 Do not use near high temperature areas. 


 Do not immerse the battery in water, seawater, or get it wet. This may cause internal short circuits to

 If the battery protection circuit does not
function properly due to high temperature, or it is broken, the battery will be charged at an abnormal
current, and abnormal chemical reaction may occur, causing the battery to rupture, generate heat, or cause

 If the battery is charged
in unusual conditions, it will cause loss of safety functions, or abnormal chemical reactions, causing the

 Do not try to damage the battery. Do not drive a nail into the battery, strike it with a hammer, or tread on

 Do not attempt to solder anything onto the battery. This will cause the insulator to melt due to heat, or

 Do not connect battery to a plug socket or car-cigarette plug. Connecting high voltage to the battery,


 Do not use battery for powering other equipment. If the battery is used for powering other equipment, it


 Do not touch a leaked battery directly. If battery leaks and hands touch leaked electrolyte, wash your
hands with soap immediately. If leaked electrolyte gets into your eyes, do not rub them, and wash eyes

iv
immediately with fresh water. Consult a doctor immediately.
 
time, let it stop charging. There is a possibility that the battery might be defective, and continued charging

 Do not insert battery into a microwave or high pressure container. This may cause battery to deform,

condition of the battery.
 If liquid leaks from the battery, or the battery give outs a bad smell,


 Do not use an abnormal battery. If battery has a bad smell, changes color, deforms, or causes something
wrong during usage, remove it from equipment or charger, and do not use. If an abnormal battery is used, it

WARNING
Warning! Batteries may explode if not handled properly. Do not
disassemble or dispose of them in fire. Keep them away from children.
Follow local regulations when disposing of used batteries.
娤⌈
󰶕㭊䢡✗㛛㏂曢㱇㛪㛰䇭䂟䙫⍘暑˛€⏖㛛㏂䂡⻇┭⻡字䙫䛟⏳曢㱇ㇽ䛟⏳❲
⻶曢㱇˛媲ᾄ㓁⻇┭媑㗵㛟㢫何曢㱇˛
㮦⿍
䔏攀寖❲⏞䔜㱇㛛㍉ἁ㛰䇭䂟⍘晐⊈⾬㋰䅎寛㗵⣫何䔏⭳䙫䔜㱇˛
㮦⿍
㭊ẋ㏂曢㱇䇭䙡⍘晡˛壤怇㥔俬㎏⥏曢
㱇⎯⏳Εͺέ曢㱇ẋ㏂󰶓˛ὦ䔏⽳曢㱇㍏㘩壤怇㥔
俬㋮䤡⽺󰶓˛

v
TABLE OF CONTENTS
CHAPTER 1 GETTING STARTED................................................ 1
Unpacking the OT-200 ..................................................................................1
Checking the package contents ....................................................................2
Identifying components .................................................................................4
Charging Cradle.............................................................................................8
Setup the OT-200...........................................................................................9
Using the cradle ...........................................................................................12
Charge the device in cradle .........................................................................12
Charge the battery in cradle.........................................................................12
Changing the battery....................................................................................13
Using MicroSD cards ...................................................................................16
Installing a MicroSD card .............................................................................16
View the contents of a MicroSD card...........................................................19
CHAPTER 2 USING THE DEVICE ............................................. 21
Entering text.................................................................................................21
Shortcut menus............................................................................................21
Performing a reset........................................................................................22
Opening and closing programs ....................................................................22
Status icons..................................................................................................22
Adjusting the volume....................................................................................23
Changing the device name ..........................................................................24
Entering owner information ..........................................................................25
Recalibrating the screen ..............................................................................26
Setting the date and time .............................................................................27
Turning WiFi, Bluetooth on or off .................................................................28
Setting the screen orientation ......................................................................29
Connecting to a WiFi network ......................................................................30
Automatically connect to a WiFi network .................................................30
Manually connect to a WiFi network ........................................................31
Find your IP address................................................................................32
Specify the IP address and domain name servers (DNS) .......................32
Lock OT-200.................................................................................................34
Unlock OT-200 .............................................................................................35
Synchronization............................................................................................36
Synchronize your data with ActiveSync and Windows XP...........................36
Synchronize your data with ActiveSync and Windows Vista/ 7....................37

vi
...............................38
!"#$%&' ..............................38
#*+"#;<=&' .............................38
Install and remove programs........................................................................39
CHAPTER 3 USING THE ACCESSORIES ............................... 41
Attaching the stylus cord..............................................................................41
Attaching the hand strap ..............................................................................42
Using the leather pouch ...............................................................................43
Attaching the leather pouch cord .................................................................44
Using the high quality stylus.........................................................................45
APPENDIX .................................................................................. 47
Troubleshooting ...........................................................................................47
Tips for Troubleshooting...............................................................................47
General Problems .......................................................................................47
Having the OT-200 Serviced .......................................................................48
Guidelines for care and maintenance ..........................................................48
Using the device ......................................................................................48
Cleaning the device .................................................................................48
Transporting and storing the device.........................................................48
!...............................................................................................49

49
CPU Samsung S3C6410 667 MHz processor
Operating System Microsoft®Windows™ Mobile 6.5 Professional
Display 4.3” TFT LCD with Touch Screen, widescreen 800*480
Memory 256MB Flash, 256MB SDRAM
Communication WiFi 802.11 b/g
Bluetooth 2.0 class 2
Telecom standards
 EDGE
 Atheros
Extension slot 
Interface Mini-USB 2.0
Other


Internal microphone
Speaker


Features
Wireless roaming
5510 Lock
Battery cover safety protection
Remote Desktop
Lock screen
Ruggedness IP54
1.2 meters drop tested
Environmental Operating temperature: 0oC to 40oC
Storage temperature: -20oC to 60oC
Battery 
Dimensions
 82 *133 * 19 mm
Weight Approximately 245g with battery
Optional modules 

Accessories AC adaptor, Cradle, Battery Stylus cord, Hand strap, Leather pouch,
Leather pouch cord, Shoulder strap, High quality stylus


EMC: FCC / CE / 3C / BSMI / VCCI



2 CHAPTER 1 GETTING STARTED
Checking the package contents
After you unpack the device check that the following items are included.
OT-200 Stylus
Battery
High quality stylus
AC adaptor
Cradle
mini-USB to USB cable

49
CPU Samsung S3C6410 667 MHz processor
Operating System Microsoft®Windows™ Mobile 6.5 Professional
Display 4.3” TFT LCD with Touch Screen, widescreen 800*480
Memory 256MB Flash, 256MB SDRAM
Communication WiFi 802.11 b/g
Bluetooth 2.0 class 2
Telecom standards
 EDGE
 Atheros
Extension slot 
Interface Mini-USB 2.0
Other


Internal microphone
Speaker


Features
Wireless roaming
5510 Lock
Battery cover safety protection
Remote Desktop
Lock screen
Ruggedness IP54
1.2 meters drop tested
Environmental Operating temperature: 0oC to 40oC
Storage temperature: -20oC to 60oC
Battery 
Dimensions
 82 *133 * 19 mm
Weight Approximately 245g with battery
Optional modules 

Accessories AC adaptor, Cradle, Battery Stylus cord, Hand strap, Leather pouch,
Leather pouch cord, Shoulder strap, High quality stylus


EMC: FCC / CE / 3C / BSMI / VCCI



4 CHAPTER 1 GETTING STARTED
Identifying components
This section describes the parts and connectors on the OT-200.
Front panel components
4
5
123
Figure 1.2 Front view
Component Description
1 
2 
3 
4 4.3-inch touch screen
5 Microphone

5
Top and bottom panel components
1
Figure 1.3 Top and bottom view
Component Description
1 Top hand strap eyelet
2 2.5mm microphone jack
3 Mini-USB port
4 Cradle connector
5 DC power jack
6 3.5mm headphone jack
3
2
4
6
5

6 CHAPTER 1 GETTING STARTED
Left and right side components
Figure 1.4 Left and right side view
4
1
2
3
Connector Description
1 Reset button
2 Leather pouch strap eyelet
3 Power button
4 Stylus dock

7
Back panel components
4
1
2
3
Connector Description
1 Top hand strap eyelet
2 Speaker
3 Battery cover
4 Bottom hand strap eyelet
Figure 1.5 Back view

8 CHAPTER 1 GETTING STARTED
Charging Cradle
This section introduces the charging cradle for the OT-200.
The charging cradle is used to charge the OT-200. A second slot is also available for charging a spare battery.
Top and front view of the cradle
4
1
2
3
Connector Description
1 DC power connector
2 Battery slot
3 OT-200 socket
4 Battery slot charging indicator
Figure 1.6 Top view of the cradle
Figure 1.7 Front view of the cradle

9
Setup the OT-200
Refer to the following to setup the OT-200.
1. Remove the battery
cover.
Slide the cover downwards to open.
Lift up to remove the battery cover.

10 CHAPTER 1 GETTING STARTED
2. Install the battery.
Align the battery connectors on the battery with the pins in the battery
compartment and insert the battery.
3. Replace the battery
cover.
Slide the battery cover back until it locks.
4. Install the screw if
required.

11
5. Insert the plastic hinge,
or attach the hand strap.
(Refer to Chapter
3 - Attaching the hand

6. Charge the battery.
Open the power jack cover. Plug the AC adaptor power cord into an
electrical outlet, then connect the DC plug of the adaptor cable to the
OT-200. It takes approximately 6 hours to fully charge the battery for the

CAUTION
To avoid damaging OT-200 or the AC adaptor,
make sure all connectors are properly
connected.
7. Press Power Button for

OT-200.
 To turn off OT-200.
Press Power Button

prompt, tap Power Off.

12 CHAPTER 1 GETTING STARTED
Using the cradle
The charging cradle allows a more convenient way to charge OT-200. You can charge a spare battery

Charge the device in cradle
1. Plug the AC adaptor power cord into an electrical
outlet, then connect the DC plug of the adaptor
cable to the power jack at the back of cradle.
2. Insert OT-200 into the cradle with front of device on
same side as front of cradle.
3. When device is inserted into cradle correctly, the
Power LED on top left of device should turn red.
Device charging is complete when the device Power
LED turns green.
Charge the battery in cradle
1. Plug the AC adaptor power cord into an electrical outlet, then connect the DC plug of the adaptor cable to
the power jack at the back of cradle.
2. Align the battery connectors on the battery with the
pins in the second battery slot of the cradle, then
install the battery in the direction of the arrow.
3. When battery is inserted into cradle correctly, the
battery LED on the cradle should light up red.
Battery charging is complete when the battery LED
on the cradle turns green.
IMPORTANT
To protect and prolong the life of the battery, do not charge it for 24
hours or longer at a time.
If battery is not used, please store in dry area, ideally with storage

"#
IMPORTANT