Philips Micro Pure WP3811 User manual

WP3811,WP3810

2

3
1

4

WP3811,WP3810
ENGLISH 6
PORTUGUÊS DO BRASIL 17

6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
General description (Fig. 1)
AFilter cartridge
B Water purier housing
CWater selection lever
DStainless steel screen
ERubber washer
FAdapter
1 A-type
2 B-type
3 C type
4 D-type
GAttachment nut
HFiltered water outlet
I Unltered water inlet
J Hollow bre
KGranular activated carbon
Important
Read this user manual carefully before you use the water purier and
save it for future reference.
Warning
The water purier is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given
supervision or instruction concerning use of the water purier by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with
the water purier.
-
-
ENGLISH

Do not let water hotter than 50°C run through the water
purier, this may cause damage.
Do not let the water purier freeze.
Before daily use
To prevent quick clogging of the lter cartridge, let the water run at
the unltered setting for around 5 seconds before every use.
If the water is highly coloured or turbid due to work on your water
network, do not let the water run at the ltered setting until the
water is clear.
Cautions:
1 Let the water run at the ltered setting for 10 seconds before use
each day.
2 Let the water run at the ltered setting for 60 seconds before use if
you have not used the water purier for more than two days.
3 If you have not used the water purier for more than two weeks, let
the water run at the ltered setting for 2-3 minutes before use. If the
lter cartridge emits an unpleasant smell, replace it with a new one.
Applications
Only use the water purier to lter water that meets drinking water
standards.
Do not block the ltered water outlet or connect other devices to it.
If the water pressure is very high, reduce the water ow of the tap to
prevent damage to the cartridge.
Keep the water purier away from heat to avoid distortion or
breakage.
Do not tamper with the water purier.
Do not remove the lter cartridge while you use the water purier
Do not use the water purier without a lter cartridge.
Do not place the water purier near a window where it is exposed
to direct sunlight.
This water purier does not soften water.
Do not use ltered water in aquariums. Tap water, ltered or
unltered, can be harmful to sh.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ENGLISH 7

Do not store puried water to avoid contamination. Air contact
contaminates puried water quickly. If you want to store puried
water, use a clean container and keep it in the refrigerator. Do not
keep it in the refrigerator longer than 1 day to avoid contamination.
Features
Philips’ multi-ltration system consists of a primary lter, a secondary
lter, a high-tech hollow-bre membrane lter and a granular
activated carbon lter.
The hollow bre membrane contains 520 billion micropores
(WP3811) or 400 billion micropores (WP3810) that are small
enough to remove particles down to 0.1µm. It eliminates 99.99%* of
bacteria, rust and other particles larger than the micropore size
from your tap water without removing calcium, magnesium and other
minerals that are vital to your body. (* tested according to Japanese
Water Purier Association (JWPA) standard).
The granular activated carbon removes the unpleasant chlorine smell
and taste from your tap water.
Apart from the recommended cartridge lifetime, Philips’ unique
cartridge replacement indicator helps you determine when to replace
the lter cartridge.
Preparing for use
Before installation
Before you install the water purier, make sure all tap-mounting
adapters you require are present.
The tap must have a diameter of 13mm-25mm.
Determine what type of tap you have and select the appropriate
adapter.
The adapters supplied make the water purier suitable for almost
any kitchen tap. However, the water purier may not t some
uncommon types of taps.
The tap water pressure has to be between 0.7kgf/cm² (7 metres of
water column) and 3.5kgf/cm² (35 metres of water column). If you
use the water purier at a water pressure outside this range, either
-
-
-
-
-
-
-
-
-
-
ENGLISH8

the ltered water ow will be extremely low or the water purier
will get damaged.
Installation A-type adapter
For taps with a round spout with a diameter of 16mm, 17.5mm or
19mm (Fig. 2).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 3).
2 Pass the attachment nut over the tap spout (Fig. 4).
3 Place the matching adapter (A-type) over the tip of the spout. The
16mm adapter is packed with the water purier. Replace it with
the 17.5mm adapter or 19mm adapter to t the diameter of your
tap (Fig. 5).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 6).
Installation B-type adapter
For taps with an aerator (threaded on the outside) (Fig. 7).
1 Remove the attachment nut and the adapter from the water
purier (Fig. 8).
2 Remove the aerator cap from the tap and pass the attachment nut
over the spout. Take out the original adapter and screw the
matching adapter (B-type) onto the tap (Fig. 9).
3 Tighten the adapter further with a coin (Fig. 10).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 11).
Installation C-type adapter
For taps with an aerator (threaded on the inside) (Fig. 12).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 13).
-
-
-
ENGLISH 9

2 Remove the aerator cap from the tap. Take out the original adapter
and screw the matching adapter (C-type) onto the tap through the
attachment nut. (Fig. 14)
3 Tighten the adapter further with a coin (Fig. 15).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 16).
Installation D-type adapter
For taps other than A, B or C. (Fig. 17)
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 18).
2 Take out the original adapter and screw the D-type adapter onto
the water purier housing. (Fig. 19)
3 Push the water purier housing onto the tap from below and
tighten the 4 screws evenly (Fig. 20).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 21).
Make sure the rubber washer is rmly pushed against the tap to prevent
water leakage.
Installing the lter cartridge
1 Make sure the tap is closed.
2 Set the water selection lever to the unltered stream
position (Fig. 22).
3 Tilt the lter cartridge 90° backwards and insert it into the water
purier housing. (Fig. 23)
4 Pull the cartridge upwards until it is in upright position. (Fig. 24)
5 Air trapped inside the lter cartridge affects the ow rate of the
ltered water. To avoid this, slightly open the tap and let water run
through the lter cartridge for 30 seconds. The slow water ow
forces out any air that is trapped inside the lter.
-
ENGLISH10

Using the water purier
1 Turn the water selection lever to the desired setting (‘click’).
The water selection lever has 3 settings: ltered spray, unltered spray
and unltered stream. See the sections below.
Do not let water hotter than 50°C run through the water purier, as
this may damage the water purier.
2 Open the tap.
Filtered spray
Select this setting for drinking, washing vegetables or fruits and
for cooking.
1 Turn the water selection lever until the ltered spray symbol is
aligned with the indicator (Fig. 25).
If you lter water between 35°C and 50°C, the water may have an
unpleasant smell. The lter cartridge has absorbed this smell during
ltering, but releases it again if you lter water hotter than 35°C.
Unltered spray
Select this setting for washing dishes and other jobs that require a gentle
water ow.
1 Turn the water selection lever until the unltered spray symbol is
aligned with the indicator (Fig. 26).
Unltered stream
Select this setting for a strong water ow.
1 Turn the water selection lever until the unltered stream symbol is
aligned with the indicator (Fig. 22).
Cleaning
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the water purier. These substances
may cause cracking, discolouration or distortion.
ENGLISH 11

1 Clean the ltered water outlet with a clean toothbrush and wipe
off any contamination with a clean cloth.
Note: Do not use a used toothbrush, as it may transfer bacteria to the water
outlet.
Replacement
New lter cartridges are available under the following type numbers:
WP3911 for water purier WP3811.
WP3910 for water purier WP3810.
However, the housing of both water puriers is suitable for both types of
lter cartridges.
Replace the lter cartridge if it is clogged to prevent damage to the
water purier.
No part of the cartridge can be reused. Discard the used cartridge and
replace it with a new one.
When to replace the lter cartridge
The actual lifetime of the lter cartridge depends on the quality of the
local water and the water pressure.
For optimal performance of the water purier, replace the lter cartridge
if one of the following situations occurs:
A You have used the lter cartridge for six months.
B The hollow bre of the lter cartridge (visible through the cartridge
window) has turned rust brown or dark grey (see section ‘Cartridge
replacement indicator’).
C The volume of puried water decreases substantially.
D The ltered water still has an unpleasant smell or is still turbid
after purication.
Reduced lter cartridge life
The lter cartridge has a shorter life and should be replaced more
frequently in the following situations:
The water pressure is very low.
The pipes and water tank are worn.
-
-
-
-
-
ENGLISH12

The tap water is contaminated due to plumbing activities or cleaning
of the water tank.
When you use cloudy water immediately after heavy rain.
Cartridge replacement indicator
Tip: Remove the cover of the lter cartridge and stick the cartridge
replacement indicator to the inside of the cover. Check the colour of the
hollow bre of the lter cartridge through the cartridge window from time to
time. If the colour of the lter matches the rust brown or dark grey shown on
the cartridge replacement indicator, replace the lter cartridge (Fig. 27).
To help you determine when to replace the lter cartridge, the water
purier and each replacement lter cartridge comes with a self-adhesive
colour-coded cartridge replacement indicator. Place this replacement
indicator in a convenient place for future reference.
How to replace the lter cartridge
1 Close the tap and set the water selection lever to the unltered
stream position. (Fig. 22)
2 Tilt the used lter cartridge 90° backwards and pull it off the water
purier housing (Fig. 23).
3 Write down the replacement date on the information label of the
new cartridge.
4 Tilt the new lter cartridge 90° backwards and insert it into the
water purier housing.
5 Pull the cartridge upwards until it is in upright position. (Fig. 24)
Environment
Do not throw away the water purier with the normal household
waste at the end of its life, but hand it in at an ofcial collection point
for recycling. By doing this, you help to preserve the
environment (Fig. 28).
-
-
-
ENGLISH 13

Guarantee & service
If you need service or information or if you have a problem, please visit
the Philips website at www.philips.com or contact the Philips Consumer
Care Centre in your country (you nd its phone number in the
worldwide guarantee leaet). If there is no Consumer Care Centre in
your country, go to your local Philips dealer.
Troubleshooting
This chapter summarises the most common problems you could
encounter with the water purier. If you are unable to solve the problem
with the information below, contact the Consumer Care Centre in your
country.
Question Answer
Why does water
leak from
the attachment nut?
Perhaps you have not installed the water
purier properly. Reinstall the water purier
according to the instructions in this user manual.
Perhaps the attachment nut or the tap-
mounting adapter is damaged. Contact an
authorised Philips service centre.
Perhaps the tap water pressure is higher than
specied.
You may need to wind some Teon tape around
the thread of the adapter.
Why is the water
ow weak at
the unltered
setting?
Perhaps the stainless steel screen under the
rubber washer inside the water purier housing
is clogged. Clean it with a toothbrush and rinse
it.
Why is the water
ow is weak at the
ltered setting?
Perhaps the lter cartridge is clogged. Replace
the lter cartridge.
ENGLISH14

Question Answer
Perhaps the tap water pressure is lower than
specied.
Product specications
The specications below are according to Japanese Industrial Standards
(JIS) s 3201.
Product name and
type number Pure water on tap WP3811/WP3810
Type Direct tap mount
Major lter
components Polysulphone hollow-bre membrane and granular activated carbon
Initial water ow
rate 2ltrs/min. (water pressure at 1kgf/cm2, water temperature at 20°C)
Chlorine
reduction capacity WP3911: 2,500ltrs (water density at 2ppm); WP3910: 1,500ltrs (water density at 2 ppm)
Turbidity reduction
capacity WP3911: 3,000ltrs (water turbidity at 2NTU); WP3910: 1,500ltrs (water turbidity at 2NTU)
Filter life WP3911: Approximately 6 months at 10ltrs a day;
WP3910: approximately 3 months at 10ltrs a day.
The actual life depends on the quality of the local
water and the water pressure.
Replacement lter
cartridge WP3911 or WP3910
Minimum water
pressure 0.7kgf/cm² (7 metres of water column/70kPa)
ENGLISH 15

Maximum water
pressure 3.5kgf/cm² (35 metres of water column/350kPa)
Accessories WP3911 or WP3910 lter cartridge, 9 tap-
mounting adapters, cartridge replacement
indicator
Product
dimensions WP3811: 105mm x 138mm x 61mm; WP3810: 91mm x 129mm x 56mm (H x W x D)
Packaging
dimensions 140mm x 170mm x 84mm (H x W x D)
Weight WP3811: approximately 330g; WP3810:
approximately 183g
Country of origin Japan
ENGLISH16

17
Introdução
Parabéns pela sua compra e bem-vindo à Philips! Para aproveitar ao
máximo o suporte oferecido pela Philips, registre o produto em www.
philips.com/welcome.
Descrição geral (g. 1)
A Rel do ltro
B Suporte do puricador de água
CChave seletora de água
DTela de aço inoxidável
EAnel de borracha
FAdaptador
1 Tipo A
2 Tipo B
3 Tipo C
4 Tipo D
G Anel cromado de xação
H Saída de água ltrada
I Entrada de água não ltrada
JMembrana microporosa
K Carvão ativado granular
Importante
Leia este manual atentamente antes de usar o puricador de água e
guarde-o para consultas futuras.
Aviso
O puricador de água não deve ser usado por pessoas (inclusive
crianças) com capacidades físicas, mentais ou sensoriais reduzidas ou
pouca experiência e conhecimento, a menos que sejam
supervisionadas ou instruídas sobre o uso do puricador de água por
uma pessoa responsável por sua segurança.
Crianças pequenas devem ser supervisionadas para que não
brinquem com o puricador de água.
-
-
PORTUGUÊS DO BRASIL

Não deixe a água passar pelo puricador a uma temperatura
superior a 50°C. Isso pode danicar o aparelho.
Não deixe o puricador de água congelar.
Antes do uso diário
Para evitar o entupimento precoce do rel do ltro, coloque a chave
seletora no ajuste “Água Não Filtrada” e deixe a água uir por 5
segundos antes de cada utilização.
Se a água não estiver transparente ou estiver turva devido a reparos
na tubulação, não deixe-a uir no ajuste “Água Filtrada” até que esteja
limpa.
Avisos:
1 Deixe a água uir no ajuste “Água Filtrada” por 10 segundos todos os
dias antes de usá-la.
2 Deixe a água uir no ajuste “Água Filtrada” por 60 segundos antes de
usá-la se não tiver usado o puricador de água por mais de dois dias.
3 Se não tiver usado o puricador de água por mais de duas semanas,
deixe a água uir no ajuste “Água Filtrada” por 2 a 3 minutos antes de
usá-la. Se o rel do ltro liberar um odor desagradável, substitua-o
por um novo.
Aplicações
Use o puricador de água somente para ltrar água que atenda aos
padrões de água potável, ou seja, água proveniente das Companhias
de Abastecimento de Água de sua cidade.
Não bloqueie nem conecte outros dispositivos à saída de Água
Filtrada.
Se a pressão da água estiver muito alta, reduza o uxo de água da
torneira para evitar danos ao rel do ltro.
Mantenha o puricador de água longe do calor para evitar
deformação ou avaria.
Não adultere o puricador de água.
Não remova o rel do ltro enquanto estiver usando o puricador
de água.
Não use o puricador sem um rel do ltro.
-
-
-
-
-
-
-
-
-
-
-
-
PORTUGUÊS DO BRASIL18

Não coloque o puricador de água onde haja incidência direta da luz
do sol.
O puricador de água não torna a água leve.
Não use água ltrada em aquários. A água da torneira, ltrada ou não,
pode ser prejudicial aos peixes.
Para evitar contaminação, não armazene a água ltrada. O contato
com o ar contamina rapidamente a água. Se desejar armazenar a água
ltrada, use um recipiente limpo e mantenha-o no refrigerador por
no máximo um dia para evitar contaminação da água.
Recursos
O sistema de multiltração da Philips consiste em um ltro principal,
um ltro secundário, um ltro de membrana microporosa de alta
tecnologia e um ltro de carvão ativado granular.
A membrana microporosa contém mais de 520 bilhões de
microporos (WP3811) ou 400 bilhões de microporos (WP3810)
pequenos o suciente para remover partículas de até 0,1µm. Ela
elimina 99,99%* das bactérias, ferrugem e outras partículas (maiores
que os microporos) da água da torneira, sem remover o cálcio, o
magnésio e outros minerais vitais para o organismo. (* testada de
acordo com o padrão da JWPA, Japanese Water Purier Association).
O carvão ativado granular remove o cheiro e o gosto desagradáveis
do cloro da água proveniente da torneira.
Além da vida útil recomendada para o rel do ltro, o exclusivo
Adesivo Indicador de Substituição de Rel da Philips ajuda
a determinar quando o rel do ltro deve ser substituído.
Preparação para o uso
Antes da instalação
Antes de instalar o puricador de água, verique se possui todos os
adaptadores necessários para a montagem na torneira.
A torneira deve ter um diâmetro de 13 a 25 mm.
Verique o tipo da sua torneira e selecione o adaptador apropriado.
-
-
-
-
-
-
-
-
-
-
-
PORTUGUÊS DO BRASIL 19

Os adaptadores fornecidos tornam o puricador de água apropriado
para quase todos os tipos de torneira de cozinha. No entanto, talvez
não se encaixe em certos tipos de torneiras não convencionais.
A pressão da água da torneira deve ser entre 0,7 kgf/cm² (7 metros
de coluna de água) e 3,5 kgf/cm² (35 metros de coluna de água). Se
você usar o puricador de água com uma pressão fora dessa faixa, o
uxo de água ltrada cará extremamente fraco ou o puricador
será danicado.
Instalação do adaptador tipo A
Para torneiras com um cano com diâmetro de 16 mm, 17,5 mm ou
19 mm (g. 2).
1 Remova o anel cromado de xação e o adaptador do suporte do
puricador de água (g. 3).
2 Introduza o anel cromado de xação na torneira (g. 4).
3 Encaixe o adaptador correspondente (tipo A) na saída de água da
torneira. O adaptador de 16 mm é fornecido com o ltro de água.
Substitua-o pelo adaptador de 17,5 mm ou 19 mm de acordo com
o diâmetro da sua torneira (g. 5).
4 Aperte o anel cromado de xação rmemente no suporte do
puricador de água (g. 6).
Instalação do adaptador tipo B
Para torneiras com arejador (preso por fora/com rosca
externa) (g. 7).
1 Remova o anel cromado de xação e o adaptador do puricador
de água (g. 8).
2 Remova o arejador da torneira e introduza o anel cromado de
xação na torneira. Retire o adaptador original e enrosque o
adaptador correspondente (tipo B) na torneira (g. 9).
3 Aperte mais o adaptador usando uma moeda (g. 10).
4 Enrosque o anel cromado de xação rmemente no suporte do
puricador de água (g. 11).
-
-
-
-
PORTUGUÊS DO BRASIL20