Phocos CA06-2.1 User manual

CA06-2.1, CA08-2.1, CA10-2.1, CA14-1.1
Phocos AG, Germany
[email protected]
Phocos China Ltd., China
[email protected]
Phocos India Solar Pvt. Ltd., India
[email protected]
Phocos Latin America S.R.L, Bolivia
[email protected]
Phocos Rep. Office A stralia, A stralia
[email protected]
Phocos Rep. Office Brazil, Brazil
Info- [email protected]
Phocos Rep. Office Eastern Africa, Kenya
[email protected]
Phocos Eastern E rope S.R.L., Romania
[email protected]
Phocos SEA Pte Ltd, Singapore
[email protected]
Phocos Rep. Office So th Africa
[email protected]
Phocos T nisia
Info-maghre @phocos.com
Phocos USA
[email protected]
www.phocos.com
Datasheet_CA_FRA
Final Version
Type CA06-2.1 CA14-1.1
CA08-2.1 CA10-2.1

Phocos CA
CID: 181802511

1~13
14~26
27~39
40~52
53~65
66-77
CONTENTS

Phocos CA
Solar - Ladere ler
Bedienun sanleitun (Deutsch)
1

Funktionsbeschreibung
2

3
Montage und Anschluss

4

5

6
Erdung des Solarsystems

7
Inbetriebnahme
inweise zum Betrieb

8
Anzeigefunktionen im Normalbetrieb
Ladun sanzei e
Batteriespannun
Lastzustandsanzei e
Ladungsanzeige

9
Tiefentladeschutz (LVD)
OK
(LED aus)
erin
(LED an)
sehr erin
(LED blinkt)
Batteriespannung

10
-------
------- -------
Schutzfunktionen

11
Allgemeine Sicherheits- und Verwendungshinweise
Fehlerbeschreibung
Fehler Anzeige Ursache Abhilfe

12
Sicherheitshinweise
aftungsausschluss

13
Technische Daten
RoHS
ISO9001:2000

Solar Charge Controller
User Manual (English)
Phocos CA
Dear customer,
Thank you very much for buyin
this Phocos product. Please read
the instructions carefully and
thorou hly before usin the
product.
14

Your new CA controller is a state-of-the art device which was
developed in accordance with the latest available technical
standards. It comes with a number of outstandin features, such
as:
3 LEDs for a clear, readable display of the state of char e
16 mm2 connector clamps
Temperature compensation
Electronic protection without fuses
Please read this manual carefully takin special note of the safety
and usa e recommendations at the end. The manual ives important
recommendations for installin , usin and pro rammin as well
as a troubleshootin uide for potential problems with the controller.
The char e controller protects the battery from bein overchar ed
by the solar array and from bein deeply dischar ed by the
loads. The char in takes place throu h multiple sta es which
include automatic adaptation to the ambient temperature for
optimal char in of the battery.
The controller is intended for use at 12 V system volta e.
The char e controller has a number of safety and display
functions.
Description of Functions
15

16
When mountin the controller with
screws, make sure to use screws that
suit the attachment material (use
screws with 4 mm shaft and max. 8
mm head diameter, no counter sink).
Keep in mind that the screws also have
to carry the force applied by the wirin .
Make sure that the ventilator slits on
the sides are unobstructed.
The controller is intended for indoor use only. Protect it from
direct sunli ht and place it in a dry environment. Never install it
in humid rooms (like bathrooms). The controller measures the
ambient temperature to determine the char in volta e. Controller
and battery must be installed in the same room.
The controller warms up durin operation, and should therefore
be installed on a non flammable surface only.
Mounting and Connecting
REMARK: Connect the controller by following the steps described
below to a oid installation faults.

A DIN Rail mountin plate is available as an accessory (CX-DR2).
This allows mountin the controller on a standard 35mm DIN rail.
Place the controller on the mountin plate, and use the screws
supplied with the mountin plate to fix it to the controller.
Connect the wires leadin to the battery
with correct polarity. To avoid any
volta e on the wires, first connect the
controller, then the battery. Keep in
mind the recommended wire len th
(min. 30 to max approx. 100 cm) and
the wire size:
CA06-2.1: min. 2.5mm2
CA08-2.1: min. 4mm2
CA10-2.1: min. 6mm2
CA14-1.1: min. 10mm2
17
WARNING: If the battery is connected with re erse polarity,
the charge controller will also gi e the wrong polarity on the
load terminals. Ne er connect loads in this situation!
REMARK: Keep in mind the recommendations of your battery
manufacturer. We strongly recommend connecting a fuse
directly to the battery to protect any short circuit at the
battery wiring. The fuse type must be in accordance with the
charge controller's nominal current:
CA06, CA08-2.1: 20A; CA10-2.1,CA14-1.1:30A