Phoenix Contact FL SWITCH 2005 User manual

User manual
FL SWITCH 2000
Order No. —

2017-05-24
PHOENIX CONTACT 107065_en_01
FL SWITCH 2000
UM EN FL SWITCH 2000
01
—
Designation Order No. Designation Order No.
FL SWITCH 2005 2702323 FL SWITCH 2206-2FX SM 2702331
FL SWITCH 2008 2702324 FL SWITCH 2206-2FX ST 2702332
FL SWITCH 2105 2702665 FL SWITCH 2206-2FX SM ST 2702333
FL SWITCH 2108 2702666 FL SWITCH 2204-2TC-2SFX 2702334
FL SWITCH 2205 2702326 FL SWITCH 2206-2SFX 2702969
FL SWITCH 2208 2702327 FL SWITCH 2308 2702652
FL SWITCH 2207-FX 2702328 FL SWITCH 2304-2GC-2SFP 2702653
FL SWITCH 2207-FX SM 2702329 FL SWITCH 2306-2SFP 2702970
FL SWITCH 2206-2FX 2702330
User manual
Designation:
Revision:
Order No.:
This user manual is valid for:

PHOENIX CONTACT
Please observe the following notes
User group of this manual
The use of products described in this manual is oriented exclusively to:
– Qualified electricians or persons instructed by them, who are familiar with applicable
standards and other regulations regarding electrical engineering and, in particular, the
relevant safety concepts.
– Qualified application programmers and software engineers, who are familiar with the
safety concepts of automation technology and applicable standards.
Explanation of symbols used and signal words
How to contact us
Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be
found on the Internet at:
phoenixcontact.com
Make sure you always use the latest documentation.
It can be downloaded at:
phoenixcontact.net/products
Subsidiaries If there are any problems that cannot be solved using the documentation, please contact
your Phoenix Contact subsidiary.
Subsidiary contact information is available at phoenixcontact.com.
Published by PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
GERMANY
Should you have any suggestions or recommendations for improvement of the contents and
layout of our manuals, please send your comments to:
[e-mail]
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety measures that follow this symbol to avoid possible
injury or death.
There are three different categories of personal injury that are indicated with a
signal word.
DANGER This indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING This indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION This indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
This symbol together with the signal word NOTE and the accompanying text
alert the reader to a situation which may cause damage or malfunction to the
device, hardware/software, or surrounding property.
This symbol and the accompanying text provide the reader with additional
information or refer to detailed sources of information.

Please observe the following notes
PHOENIX CONTACT
General terms and conditions of use for technical documentation
Phoenix Contact reserves the right to alter, correct, and/or improve the technical
documentation and the products described in the technical documentation at its own
discretion and without giving prior notice, insofar as this is reasonable for the user. The
same applies to any technical changes that serve the purpose of technical progress.
The receipt of technical documentation (in particular user documentation) does not
constitute any further duty on the part of Phoenix Contact to furnish information on
modifications to products and/or technical documentation. You are responsible to verify the
suitability and intended use of the products in your specific application, in particular with
regard to observing the applicable standards and regulations. All information made
available in the technical data is supplied without any accompanying guarantee, whether
expressly mentioned, implied or tacitly assumed.
In general, the provisions of the current standard Terms and Conditions of Phoenix Contact
apply exclusively, in particular as concerns any warranty liability.
This manual, including all illustrations contained herein, is copyright protected. Any
changes to the contents or the publication of extracts of this document is prohibited.
Phoenix Contact reserves the right to register its own intellectual property rights for the
product identifications of Phoenix Contact products that are used here. Registration of such
intellectual property rights by third parties is prohibited.
Other product identifications may be afforded legal protection, even where they may not be
indicated as such.
Caution: Installation only by qualified personnel
Installation, startup and maintenance of the product may only be performed by qualified
specialist staff who have been authorized for this by the system operator. An electrician is a
person who, because of their training, experience and instruction, and knowledge of rele-
vant standards, can assess any required operations and recognize any possible dangers.
Specialist staff must read and understand this documentation and comply with instructions.
Observe the national regulations in force for the operation, functional testing, repairs and
maintenance of electronic devices.

Table of contents
107065_en_01 PHOENIX CONTACT 5 / 20
Table of contents
1 Factoryline SWITCH 2000 range ...............................................................................................7
1.1 Properties and versions......................................................................................... 7
1.1.1 Dimensions of the FL SWITCH 2000 ..................................................... 8
1.1.2 Elements of the devices ......................................................................... 9
1.1.3 Description of the combo ports ..............................................................9
1.1.4 Status and diagnostic indicators .......................................................... 10
2 Mounting and installation .........................................................................................................11
2.1 Mounting and removing the devices.................................................................... 11
2.2 Installing the devices ........................................................................................... 12
2.2.1 Connecting the supply voltage .............................................................12
2.2.2 Grounding ? ......................................................................................... 14
2.2.3 Assignment of the RJ45 Ethernet connectors ......................................14
2.2.4 Use of SFP slots (principle) .................................................................. 14
2.2.5 Using the SD card ................................................................................ 16
3 Startup and function .................................................................................................................17
3.1 Delivery state/factory settings..............................................................................17
3.2 Using Smart mode............................................................................................... 17
3.2.1 Calling Smart mode ............................................................................. 17
Factoryline SWITCH 2000 range3.2.2Selecting the desired setting ................... 18
3.2.3 Possible operating modes in Smart mode ............................................18
3.2.4 Exiting Smart mode .............................................................................. 18
3.2.5 Operating with a default IP address .....................................................18
3.2.6 Operating in Unmanaged mode ........................................................... 19
3.3 Assigning IP parameters via BootP......................................................................19
3.3.1 Assigning the IP address using
FL NETWORK MANAGER Basic ......................................................... 19
3.3.2 Assigning the IP address using IPAssign.exe ...................................... 21
4 Frame switching .......................................................................................................................25
4.1 Store and forward................................................................................................25
4.2 Multi-address function ......................................................................................... 25
4.2.1 Learning addresses ............................................................................. 25
4.2.2 Prioritization ......................................................................................... 26
5 Configuration and diagnostics in web-based management ......................................................27
5.1 Requirements for the use of WBM....................................................................... 27
5.2 Functions/information in WBM............................................................................. 28
5.2.1 Information area of WBM ..................................................................... 29

Factoryline SWITCH 2000 range
6 / 20 PHOENIX CONTACT 107065_en_01
5.2.2 Configuration area of WBM .................................................................. 33
5.2.3 Diagnostics area of WBM ....................................................................52
6 Configuration and diagnostics via
Command Line Interface (CLI) .................................................................................................57
6.1 Using the Command Line Interface (CLI)............................................................. 57
6.2 Access to the CLI ................................................................................................ 57
6.3 Basic principles for using CLI commands............................................................ 58
6.4 Command syntax ................................................................................................ 59
6.5 Using the CLI Help............................................................................................... 59
6.6 Auto-completion of commands............................................................................ 60
6.7 Using the CLI Network Scripting UI......................................................................61
7 Simple Network Management Protocol (SNMP) ......................................................................63
7.1 General function .................................................................................................. 63
8 Link Layer Discovery Protocol (LLDP) .....................................................................................65
8.1 Basics.................................................................................................................. 65
9 Multicast filtering ......................................................................................................................69
9.1 Multicast Configuration........................................................................................ 69
10 Virtual Local Area Network (VLAN) ..........................................................................................71
11 Technical data and ordering data .............................................................................................75
11.1 Technical data for devices in the 2000 version.................................................... 75
11.2 Technical data for devices in the 2100 version.................................................... 76
11.3 Technical data for devices in the 2200 version.................................................... 78
11.4 Technical data for devices in the 2300 version.................................................... 81
11.5 Ordering data ...................................................................................................... 85
A Appendix for document lists......................................................................................................89
A 1 List of figures .......................................................................................................89
B 2 List of tables ........................................................................................................ 93
C 3 Index.................................................................................................................... 95

Factoryline SWITCH 2000 range
107065_en_01 PHOENIX CONTACT 7
1 Factoryline SWITCH 2000 range
1.1 Properties and versions
The Managed Switches in the 2000 version are Ethernet Switches which are suitable for in-
dustrial use. They are available in the following versions:
– With five 10/100 Mbps RJ45 ports (FL SWITCH 2005)
– With eight 10/100 Mbps RJ45 ports (FL SWITCH 2008)
The Managed Switches in the 2100 version are Gigabit Ethernet Switches which are suit-
able for industrial use. They are available in the following versions:
– With five 10/100/1000 Mbps RJ45 ports (FL SWITCH 2105)
– With eight 10/100/1000 Mbps RJ45 ports (FL SWITCH 2108)
The Managed Switches in the 2200 version are Ethernet Switches which are suitable for in-
dustrial use. They are available in the following versions:
– With five 10/100 Mbps RJ45 ports (FL SWITCH 2205)
– With eight 10/100 Mbps RJ45 ports (FL SWITCH 2208)
– With seven 10/100 Mbps RJ45 ports and one FO port in SC format for multimode (FL
SWITCH 2207-FX)
– With seven 10/100 Mbps RJ45 ports and one FO port in SC format for single mode (FL
SWITCH 2207-FX-SM)
– With six 10/100 Mbps RJ45 ports and two FO ports in SC format for multimode (FL
SWITCH 2206-2FX)
– With six 10/100 Mbps RJ45 ports and two FO ports in SC format for single mode (FL
SWITCH 2206-2FX SM)
– With six 10/100 Mbps RJ45 ports and two FO ports in ST format for multimode (FL
SWITCH 2206-2FX ST)
– With six 10/100 Mbps RJ45 ports and two FO ports in ST format for single mode (FL
SWITCH 2206-2FX SM ST)
– With four 10/100 Mbps RJ45 ports, two Fast Ethernet combo ports, and two SFX ports
(FL SWITCH 2204-2TC-2SFX)
– With six 10/100 Mbps RJ45 ports and two SFX ports
(FL SWITCH 2206-2SFX)
The Managed Switches in the 2300 version are Gigabit Ethernet Switches which are suit-
able for industrial use. They are available in the following versions:
– With eight 10/100/1000 Mbps RJ45 ports (FL SWITCH 2308)
– With four 10/100/1000 Mbps RJ45 ports, two Gigabit combo ports, and two SFP ports
(FL SWITCH 2304-2GC-2SFP)
– With six 10/100/1000 Mbps RJ45 ports and two SFP ports (FL SWITCH 2306-2SFP)

FL SWITCH 2000
8PHOENIX CONTACT 107065_en_01
1.1.1 Dimensions of the FL SWITCH 2000
Figure 1-1 Dimensions of the FL SWITCH 2000

Factoryline SWITCH 2000 range
107065_en_01 PHOENIX CONTACT 9
1.1.2 Elements of the devices
Figure 1-2 Elements of the devices
1.1.3 Description of the combo ports
Combo ports enable a high degree of flexibility when setting up networks. They consist of a
corresponding RJ45 port (e.g., X3.1) and a corresponding SFP port (e.g., X3.2). Only one
port of the pair can be used at a time. Each combo port can therefore be used as a copper
or fiberglass port. Inserting an SFP module disables the corresponding RJ45 port. If a
combo port is used as a fiberglass port, the Link LED of the corresponding RJ45 port lights
up orange when there is an active connection.
The following FL SWITCH 2000 versions have combo ports:
– FL SWITCH 2204-2TC-2SFX (2 Fast-Ethernet combo ports for 100 Mbps SFP mod-
ules, ports 3 and 7)
– FL SWITCH 2304-2GC-2SFP (2 Gigabit combo ports for 100 Mbps and 1000 Mbps
SFP modules, ports 3 and 7)
1
2
3
4
5
Table 1-1
Number Meaning
1 Connection for the supply voltage
2RJ45ports
3Modeswitch
4 Diagnostic and status indicators
5 Slot for optional SD card

FL SWITCH 2000
10 PHOENIX CONTACT 107065_en_01
1.1.4 Status and diagnostic indicators
Please note that the meaning of the LEDs differs in Smart mode (see “Using Smart mode”
on page 17).
Des. Color Status Meaning
US1 Green On Supply voltage 1 within the tolerance range
Off Supply voltage 1 too low
US2
(for 2200/2300 ver-
sion only)
Green On Supply voltage 2 within the tolerance range
Off Supply voltage 2 too low
FAIL
(for 2200/2300 ver-
sion only)
Red On Digital alarm output floated, i.e., an error is present
Off Digital alarm output connected to ground potential (ground), i.e., an
error is not present
LNK/ACT
(at port top)
Green On Link active
Flashing Data transmission
Off Link not active
SPD
(at port bottom)
Green/
orange
On Green: 100 Mbps
Orange (for 2100/2300 version only): 1000 Mbps
Off 10 Mbps if Link LED is active