Phoenix Contact FL SWITCH SMCS 16TX User manual

User manual
Smart Managed Compact Switch
UM EN FL SWITCH SMCS
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

2013-01-10
PHOENIX CONTACT 7471_en_06
Smart Managed Compact Switch
UM EN FL SWITCH SMCS
06
—
Designation Revision Order No.
FL SWITCH SMCS 16TX 2700996
FL SWITCH SMCS 14TX/2FX 2700997
FL SWITCH SMCS 14TX/2FX-SM 2701466
FL SWITCH SMCS 8GT 2891123
FL SWITCH SMCS 6GT/2SFP 2891479
FL SWITCH SMCS 6TX/2SFP 2989323
FL SWITCH SMCS 8TX 2989226
FL SWITCH SMCS 8TX-PN 2989103
FL SWITCH SMCS 4TX-PN 2989093
User manual
Designation:
Revision:
Order No.:
This user manual is valid for:
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

PHOENIX CONTACT
Please observe the following notes
User group of this manual
The use of products described in this manual is oriented exclusively to:
– Qualified electricians or persons instructed by them, who are familiar with applicable
standards and other regulations regarding electrical engineering and, in particular, the
relevant safety concepts.
– Qualified application programmers and software engineers, who are familiar with the
safety concepts of automation technology and applicable standards.
Explanation of symbols used and signal words
How to contact us
Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be
found on the Internet at:
www.phoenixcontact.com
Make sure you always use the latest documentation. 
It can be downloaded at:
www.phoenixcontact.net/catalog
Subsidiaries If there are any problems that cannot be solved using the documentation, please contact
your Phoenix Contact subsidiary.
Subsidiary contact information is available at www.phoenixcontact.com.
Published by PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
GERMANY
Should you have any suggestions or recommendations for improvement of the contents and
layout of our manuals, please send your comments to:
[e-mail]
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety measures that follow this symbol to avoid possible
injury or death.
There are three different categories of personal injury that are indicated with a
signal word.
DANGER This indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING This indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION This indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
This symbol together with the signal word NOTE and the accompanying text
alert the reader to a situation which may cause damage or malfunction to the
device, hardware/software, or surrounding property.
This symbol and the accompanying text provide the reader with additional infor-
mation or refer to detailed sources of information.
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Please observe the following notes
PHOENIX CONTACT
General terms and conditions of use for technical documentation
Phoenix Contact reserves the right to alter, correct, and/or improve the technical documen-
tation and the products described in the technical documentation at its own discretion and
without giving prior notice, insofar as this is reasonable for the user. The same applies to any
technical changes that serve the purpose of technical progress.
The receipt of technical documentation (in particular user documentation) does not consti-
tute any further duty on the part of Phoenix Contact to furnish information on modifications
to products and/or technical documentation. You are responsible to verify the suitability and
intended use of the products in your specific application, in particular with regard to observ-
ing the applicable standards and regulations. All information made available in the technical
data is supplied without any accompanying guarantee, whether expressly mentioned, im-
plied or tacitly assumed.
In general, the provisions of the current standard Terms and Conditions of Phoenix Contact
apply exclusively, in particular as concerns any warranty liability.
This manual, including all illustrations contained herein, is copyright protected. Any
changes to the contents or the publication of extracts of this document is prohibited.
Phoenix Contact reserves the right to register its own intellectual property rights for the
product identifications of Phoenix Contact products that are used here. Registration of such
intellectual property rights by third parties is prohibited.
Other product identifications may be afforded legal protection, even where they may not be
indicated as such.
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Table of contents
7471_en_06 PHOENIX CONTACT i
Table of contents
1 Smart Managed Compact Switch (SMCS) ..............................................................................1-1
1.1 Properties...........................................................................................................1-1
1.1.1 Dimensions of the SMCS (8-port versions) .........................................1-4
1.1.2 Dimensions of the SMCS (16-port versions) .......................................1-4
1.2 Status and diagnostic indicators.........................................................................1-5
2 Mounting and installation ........................................................................................................2-1
2.1 Mounting and removing the SMCS.....................................................................2-1
2.2 Installing the Smart Managed Compact Switch ..................................................2-2
2.2.1 Connecting the 24 V DC supply voltage ..............................................2-2
2.2.2 Alarm contact ......................................................................................2-3
2.2.3 Assignment of the RJ45 Ethernet connectors .....................................2-3
2.2.4 Use of SFP slots .................................................................................2-4
2.2.5 V.24 (RS-232) interface for external management ..............................2-6
2.3 Grounding...........................................................................................................2-6
3 Startup and functions ..............................................................................................................3-1
3.1 Basic settings .....................................................................................................3-1
3.1.1 Delivery state/default settings .............................................................3-1
3.2 Using Smart mode..............................................................................................3-3
3.2.1 Activating Smart mode ........................................................................3-3
3.3 Frame switching .................................................................................................3-6
3.3.1 Store-and-forward ...............................................................................3-6
3.3.2 Multi-address function .........................................................................3-6
3.3.3 Learning addresses ............................................................................3-6
3.3.4 Prioritization ........................................................................................3-7
4 Configuration and diagnostics .................................................................................................4-1
4.1 Making contact between the SMCS and PC for initial configuration ...................4-1
4.1.1 Operation with static IP addresses ......................................................4-1
4.2 Web-based management (WBM).......................................................................4-3
4.2.1 General function ..................................................................................4-3
4.2.2 Requirements for the use of WBM ......................................................4-4
4.2.3 Functions/information in WBM ............................................................4-5
4.3 Simple Network Management Protocol (SNMP)...............................................4-25
4.3.1 General function ................................................................................4-25
4.3.2 Schematic view of SNMP management ............................................4-25
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

FL SWITCH SMCS
ii PHOENIX CONTACT 7471_en_06
4.4 Management via local V.24 (RS-232) communication interface .......................4-29
4.4.1 General function ................................................................................4-29
4.4.2 User interface functions ....................................................................4-30
4.4.3 Starting with faulty software (firmware) .............................................4-33
5 (Rapid) Spanning Tree ............................................................................................................5-1
5.1 General function .................................................................................................5-1
5.2 (R)STP startup....................................................................................................5-2
5.2.1 Enabling (R)STP on all switches involved ...........................................5-2
5.2.2 Connection failure - Example ..............................................................5-9
5.2.3 Mixed operation of RSTP and STP ...................................................5-10
5.2.4 Topology detection of a Rapid Spanning Tree network (RSTP) ........5-10
5.2.5 Configuration notes for Rapid Spanning Tree ...................................5-13
5.2.6 Example topologies ..........................................................................5-16
6 Media Redundancy Protocol (MRP) .......................................................................................6-1
6.1 General function .................................................................................................6-1
6.2 MRP manager ....................................................................................................6-1
6.2.1 Network examples ..............................................................................6-2
6.3 Enabling web pages for using MRP in WBM ......................................................6-4
6.4 Configuration of MRP .........................................................................................6-4
6.4.1 MRP general .......................................................................................6-4
6.4.2 MRP configuration ..............................................................................6-5
7 Multicast filtering ....................................................................................................................7-1
7.1 Basics.................................................................................................................7-1
7.2 Enabling the web pages for multicast filtering in WBM .......................................7-1
7.3 Static multicast groups .......................................................................................7-1
7.3.1 “Current Multicast Groups” web page .................................................7-2
7.3.2 Creating static multicast groups ..........................................................7-2
7.3.3 Procedure for creating a multicast group ............................................7-4
7.4 Dynamic multicast groups ..................................................................................7-7
7.4.1 Internet Group Management Protocol (IGMP) .....................................7-7
7.4.2 “General Multicast Configuration” web page .......................................7-8
7.5.1 Properties of multicast source detection ...........................................7-10
8 Virtual Local Area Network (VLAN) .........................................................................................8-1
8.1 Basics.................................................................................................................8-1
8.2 Enabling the VLAN web pages in web-based management ...............................8-1
8.2.1 Management VLAN ID ........................................................................8-1
8.2.2 Changing the management VLAN ID ..................................................8-2
8.3 General VLAN configuration...............................................................................8-2
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Table of contents
7471_en_06 PHOENIX CONTACT iii
8.4 Current VLANs ...................................................................................................8-3
8.4.1 Static VLANs .......................................................................................8-4
8.4.2 VLAN port configuration ......................................................................8-5
8.4.3 VLAN port configuration table .............................................................8-5
8.5 Setting up static VLANs......................................................................................8-6
8.6 VLAN and (R)STP ..............................................................................................8-7
9 Operation as a PROFINET device ..........................................................................................9-1
9.1 Preparing the switch for PROFINET mode .........................................................9-1
9.2 Switch as a PROFINET IO device ......................................................................9-2
9.2.1 Configuration in the engineering tool ...................................................9-2
9.2.2 Configuring the switch as a PROFINET IO device ..............................9-3
9.2.3 Configuration via the engineering tool .................................................9-5
9.2.4 PROFINET flashing function ...............................................................9-5
9.2.5 Device naming ....................................................................................9-5
9.2.6 Operating in the PROFINET environment ...........................................9-5
9.3 PROFINET alarms..............................................................................................9-5
9.3.1 Alarms in WBM ...................................................................................9-6
9.4 Process data communication .............................................................................9-6
9.4.1 Control word .......................................................................................9-6
9.5 PDEV function description..................................................................................9-7
9.5.1 PROFINET stack and PDEV function ..................................................9-8
10 LLDP (Link Layer Discovery Protocol) ..................................................................................10-1
10.1 Basics...............................................................................................................10-1
10.2 Representation of the topology in an engineering tool......................................10-4
11 Time settings ........................................................................................................................11-1
11.1 Simple Network Time Protocol (SNTP).............................................................11-1
11.2 Configuring SNTP.............................................................................................11-2
11.2.1 WBM .................................................................................................11-2
11.2.2 SNMP ...............................................................................................11-2
12 Technical data and ordering data ..........................................................................................12-1
12.1 Technical data ..................................................................................................12-1
12.2 Ordering data ...................................................................................................12-5
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

FL SWITCH SMCS
iv PHOENIX CONTACT 7471_en_06
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Smart Managed Compact Switch (SMCS)
7471_en_06 PHOENIX CONTACT 1-1
1 Smart Managed Compact Switch (SMCS)
1.1 Properties
The Smart Managed Compact Switch (SMCS) is an industrial Ethernet switch, which is
available in the following versions:
– Eight Gigabit ports in RJ45 format (FL SWITCH SMCS 8GT)
– Six Gigabit ports in RJ45 format and two fiber optic ports as SFP slots
(FL SWITCH SMCS 6GT/2SFP)
– Eight Fast Ethernet ports in RJ45 format (FL SWITCH SMCS 8TX)
– Four Fast-Ethernet ports in RJ45 format, operating in “PROFINET” mode by default
upon delivery (FL SWITCH SMCS 4TX-PN)
– Eight Fast Ethernet ports in RJ45 format, operating in “PROFINET” mode by default
upon delivery (FL SWITCH SMCS 8TX-PN)
– Six Fast Ethernet ports in RJ45 format and two fiber optic ports as SFP slots
(FL SWITCH SMCS 6TX/2SFP)
– Sixteen Fast Ethernet ports in RJ45 format (FL SWITCH SMCS 16TX)
– Fourteen Fast Ethernet ports in RJ45 format and two fiber optic ports in SC format for
multi-mode (FL SWITCH SMCS 14TX/2FX)
– Fourteen Fast Ethernet ports in RJ45 format and two fiber optic ports in SC format for
single-mode (FL SWITCH SMCS 14TX/2FX-SM)
Figure 1-1 Examples for SMCS switches
ATTENTION: The software functions are largely the same on all of the listed
devices. They only differ with regard to the data transmission speed. Any other
differences are particularly mentioned where necessary.
ATTENTION: By default upon delivery the FL SWITCH SMCS 4/8TX-PN switch
operates in “PROFINET” mode.
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

FL SWITCH SMCS
1-2 PHOENIX CONTACT 7471_en_06
Future-proof networks for the highest demands
Maximum performance 10/100/(1000) Mbps on each RJ45 port, 1000 Mbps for SFP fiber optic ports and 100 Mbps
for SC fiber optic ports.
Maximum availability Maximum network availability
A device design that does not use a fan, the redundant power supply, and conformance with
all relevant industrial standards in terms of EMC, climate, mechanical load, etc. ensure the
highest possible level of availability.
Quick media redundancy Redundancy can also be created with standards: the (Rapid) Spanning Tree Protocol or
MRP (Media Redundancy Protocol) ensure safe operation of the entire network regardless
of topology, even in the event of a cable interrupt.
All information Clear information
You can clearly label your device and each individual port using the large labeling fields.
Two LEDs per port with switchable information ensure that you always have sufficient
information on site. A web server and an SNMP agent are provided for diagnostics,
maintenance, and configuration via the network. A terminal access point can be used for
on-site operation.
Port mirroring Port mirroring can be used to monitor data traffic on the network connections or as an
important service function.
Features and fields of application of the SMCS
– Maximum performance through Gigabit support on all ports.
– Increased network performance by filtering data traffic:
- Local data traffic remains local. 
- The data volume in network segments is reduced.
– Easy network expansion and network configuration.
– Coupling copper segments with different transmission speeds.
Automatic detection of 10 Mbps, 100 Mbps or 1000 Mbps data transmission speed with
autocrossing for the RJ45 ports.
– Flexible use of fiber optic modules in SFP ports.
– Increased availability through the use of redundant transmission paths with the shortest
switch-over times using Rapid Spanning Tree and fast ring detection. Support of
various topologies and meshed structures as well as ring topologies with special ring
detection.
– Switch configuration using web-based management, SNMP or locally via a V.24
(RS-232) interface.
– Port mirroring
– Topology detection using LLDP (Link Layer Discovery Protocol).
– Address assignment via BootP, DCP or statically.
– Media Redundancy Protocol (MRP) supported as a client. The MRP ring can therefore
be created using any SMCS ports.
– Can be used in the PROFINET environment.
– Operating mode can be easily changed using Smart mode.
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Smart Managed Compact Switch (SMCS)
7471_en_06 PHOENIX CONTACT 1-3
1.1.0.1 Front view of the SMCS
Anschluss
Versorgungsspannung
V.24-Schnittstelle
Mini-DIN
Potenzialfreier
Meldekontakt
Diagnose/
Status-Anzeigen
MODE-Umschalter
mit LEDs
Geräte-Beschrif-
tungsfeld
MAC-Adresse
00.A0.45.06.04.02
MAC
Address
1234
LINK
Mode
US2 FAIL
X9
US1 GND US2 GND
X10
R1 R2
FL SWITCH SMSC 8GT
Ord. No. 2891123
US1
X11
MEM
MODE
SPD
FD
ACT
56 7 8
X12
V.2 4
1357
2468
Port-
Beschriftungsfelder
Schema der Ethernet-
Port-Nummerierung
Ethernet-
Ports
M12-Buchse für
Parametrie ungsspeicherr
74710000
SFP-Slots
Figure 1-2 Front view of the SMCS using the example of the FL SWITCH SMCS 8GT
– Diagnostic/status indicators
Important information is displayed directly on the device. Each port has two LEDs. The
top LED always indicates the “LINK”, the display of the bottom LED is set with the func-
tion switch.
– MODE switch for LEDs and Smart mode
The MODE switch can be used to specify which information is displayed by the second
port-specific LED. The three LEDs below the switch indicate the selected mode. This
information is then displayed by all port-specific LEDs (see also example on page 1-6).
In addition, this button is used to set the switch to Smart mode (for details, see “Using
Smart mode” on page 3-3).
– Mini-DIN V.24 (RS-232)
V.24 (RS-232) interface in Mini-DIN format for on-site configuration via the serial inter-
face.
–Alarmcontact
The floating alarm contact can be connected here via a 2-pos. COMBICON connector.
– Supply voltage connection
The supply voltage can be connected via the 4-pos. COMBICON connector (redun-
dancy is optional).
– Labeling fields
The SMCS has large labeling fields, which can be used for both device labeling and
port labeling.
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

FL SWITCH SMCS
1-4 PHOENIX CONTACT 7471_en_06
1.1.1 Dimensions of the SMCS (8-port versions)
10 mm / 0.39 in.
69 mm / 2.72 in.
128 mm / 5.04 in.
00.A0.45.06.04.02
MAC
Address
1234
LINK
Mode
US2 FAIL
X9
US1 GND US2 GND
X10
R1 R2
FL SWITCH SMSC 8GT
Ord. No. 2891123
US1
X11
MEM
MODE
SPD
FD
ACT
56 7 8
X12
V.24
1357
2468
55 mm / 2.1655 in.
FL MEM PLUG
2891259
100 mm / 3.94 in.
Figure 1-3 Housing dimensions of the SMCS (8-port version) in millimeters/inches
1.1.2 Dimensions of the SMCS (16-port versions)
FL SWITCH SMCS 16TX
Ord. No. 27 00 99 6
.A0.45.1B.D2.1D
MAC
Address
1357
2468
911 13 15
10 12 14 16
91610 11 12 13 14 15
18234567
MODE
ACT 100 FD
US1 US2 FAIL
X19
MEM
X17
US1 GND US2 GND
X18
R1 R2
95 mm / 3.74 in.
10 mm / 0.39 in.
71 mm / 2.795 in.
214 mm / 8.43 in.
70582004
55 mm / 2.1655 in.
FL MEM PLUG
2891259
Figure 1-4 Housing dimensions of the SMCS (16-port version) in millimeters/inches
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Smart Managed Compact Switch (SMCS)
7471_en_06 PHOENIX CONTACT 1-5
1.2 Status and diagnostic indicators
Please note that the meaning of the LEDs differs in Smart mode (see “Using Smart mode”
on page 3-3).
Example:
In Figure 1-5, the LED indicators have the following meaning:
A: The MODE switch has been set to display the duplex mode (FD); the mode LEDs now
indicate that port 1 and port 3 are in full duplex mode, port 2 is not operating at all, and port 4
is in half duplex mode.
Des. Color Status Meaning
US1 Green ON Supply voltage 1 within the tolerance range
OFF Supply voltage 1 too low
US2 Green ON Supply voltage 2 within the tolerance range
OFF Supply voltage 2 too low
FAIL Red ON Alarm contact open, i.e., an error has occurred.
OFF Alarm contact closed, i.e., an error has not occurred.
A Link LED is located on the front of the SMCS for each port.
LNK
(Link)
Green ON Link active
OFF Link not active
An additional LED is located on the front of the SMCS for each port. The function of the second LED (MODE) for each port
can be set using the MODE switch (see also example below). There are three options (during the boot process the mode
and port LEDs are permanently on):
ACT
(Activity)
Green ON Transmitting/receiving telegrams
OFF Not transmitting/receiving telegrams
SPD
(Speed)
Green/
orange
ON
(orange)
1000 Mbps
On (green) 100 Mbps (for RJ45 ports only)
OFF 10 Mbps if Link LED is active (for RJ45 ports only)
FD
(Duplex)
Green ON Full duplex
OFF Half duplex
ACT/SPD/FD Yellow Flashing Switch is in Smart mode (see “Using Smart mode” on page 3-3).
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

FL SWITCH SMCS
1-6 PHOENIX CONTACT 7471_en_06
B: The switch has been set to display the data transmission rate (SPD); the mode LEDs now
indicate that port 1 is operating at 10 Mbps, port 2 is operating at 1000 Mbps, port 3 is oper-
ating at 100 Mbps, and port 4 is not operating at all.
Figure 1-5 Example for status indicators
AB
74710001
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Mounting and installation
7471_en_06 PHOENIX CONTACT 2-1
2 Mounting and installation
2.1 Mounting and removing the SMCS
Mount the SMCS on a clean DIN rail according to DIN EN 50 022 (e.g., NS 35 ... from
Phoenix Contact). To avoid contact resistance, only use clean, corrosion-free DIN rails. End
clamps (E/NS 35N, Order No. 0800886) can be mounted to the right and left of the SMCS
to stop the modules from slipping on the DIN rail.
Mounting:
1Place the module onto the DIN rail from above (A). The upper holding keyway of the
module must be hooked onto the top edge of the DIN rail. Push the module from the
front towards the mounting surface (B).
A2
A1
A
Figure 2-1 Snapping the SMCS onto the DIN rail
2Once the module has been snapped on properly, check that it is fixed securely on the
DIN rail. Check whether the positive latch is facing upwards, i.e., snapped on correctly.
Removal:
1Pull down the positive latch using a suitable tool (e.g., screwdriver). The positive latch
remains snapped out. Then swivel the bottom of the module away from the DIN rail
slightly (A). Next, lift the module upwards away from the DIN rail (B).
B1
B2
B
Figure 2-2 Removing the SMCS
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

FL SWITCH SMCS
2-2 PHOENIX CONTACT 7471_en_06
2.2 Installing the Smart Managed Compact Switch
2.2.1 Connecting the 24 V DC supply voltage
We recommend securing the device with a 2A fuse (slow). Appropriate fuse holder or
thermo-magnetic circuit breaker, see "Accessories" in Chapter 12.
The SMCS is operated using a 24 V DC voltage, which is applied via COMBICON. If
required, the voltage can also be supplied redundantly (see Figure 2-4).
Figure 2-3 Supplying the SMCS using one voltage source
If redundant power supply monitoring is active (default setting), an error is indicated if only
one voltage is applied. A jumper between US1 and US2 prevents this error message.
However, it is also possible to deactivate monitoring in web-based management or via
SNMP.
OUT
24 V DC
US1 US2
GND GND R1 R2
705800001
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Mounting and installation
7471_en_06 PHOENIX CONTACT 2-3
Redundant 24 V DC supply
Figure 2-4 Supplying the SMCS using two voltage sources
In order to reset the SMCS on power up, the power supply must be interrupted for at least
three seconds.
2.2.2 Alarm contact
The switch has a floating alarm contact. An error is indicated when the contact is opened.
Figure 2-5 Basic circuit diagram for the alarm contact
The indicated error states are configured in web-based management or via SNMP. For a list
of error states that can be configured, please refer to Section “Diagnostics/Alarm Contact
menu” on page 4-22.
2.2.3 Assignment of the RJ45 Ethernet connectors
Please note that for operation with 1000 Mbps (Gigabit), cables with four twisted pairs
(eight wires), which meet the requirements of Cat 5e as a minimum, must be used.
In the event of a non-redundant voltage supply, the switch indicates the voltage supply
failure by opening the alarm contact. This error message can be prevented by connecting
the supply voltage to both terminal blocks in parallel, as shown in Figure 2-3, or by deac-
tivating redundant power supply monitoring in web-based management or via SNMP.
OUT
24 V DC
US1 US2
GND GND R1 R2
R1 R2
67842015
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Table 2-1 Pin assignment of RJ45 connectors
FL SWITCH SMCS
2-4 PHOENIX CONTACT 7471_en_06
Pin number 10BASE-T/10 Mbps 100BASE-T/100 Mbps 100Base-T/1000 Mbps
1 TD+ (transmit) TD+ (transmit) BI_DA+ (bidirectional)
2 TD- (transmit) TD- (transmit) BI_DA- (bidirectional)
3 RD+ (receive) RD+ (receive) BI_DB+ (bidirectional)
4 - - BI_DC+ (bidirectional)
5 - - BI_DC- (bidirectional)
6 RD- (receive) RD- (receive) BI_DB- (bidirectional)
7 - - BI_DD+ (bidirectional)
8 - - BI_DD- (bidirectional)
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

Mounting and installation
7471_en_06 PHOENIX CONTACT 2-5
2.2.4 Use of SFP slots
The SFP slots are used by SFP modules (fiber optic fiberglass modules in SFP format). By
selecting SFP modules, the user can specify whether the switch has multi-mode or single-
mode fiber optic ports, for example.
The SFP modules are available separately as accessories, see “Technical data and order-
ing data” on page 12-1.
2.2.4.1 Elements of the SFP modules
Elektrische
Anschlusskontakte
Mechanische
Verriegelung
LWL-
Anschluss
Ausrasthebel
Figure 2-6 Elements of the SFP modules
2.2.4.2 Mounting the SFP modules
Inserting the SFP modules
•Insert the SFP modules in the relevant slots on the switch.
•Ensure correct mechanical alignment of the SFP modules.
Figure 2-7 Inserting the SFP modules
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx

FL SWITCH SMCS
2-6 PHOENIX CONTACT 7471_en_06
Connecting the fiber optic cable
•Ensure correct mechanical alignment when inserting the fiber optic connectors.
Removing the fiber optic connectors
•Press the arresting latch (A) and pull out the connector (B).
AB
Figure 2-8 Removing the fiber optic connectors
Removing the SFP modules
•Remove the fiber optic connector before removing the SFP module.
•Turn the release latch (A) down and pull out the SFP module (B).
B
Figure 2-9 Removing the SFP modules
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-14154-Phoenix-Contact-2700996-FL-SWITCH-SMCS-16TX-Managed-Ethernet-Switch.aspx