PMI SG51123 User manual

Instructions > PMI Bucket Belt
The PMI Bucket Belt (Ladder Belt) is designed especially for fall
prevention of workers in bucket trucks, and should be rigged to
prevent any possibility of a fall.
SG51123
Weight: 2.1 lbs (953 g)
INTENDED USE
USE GUIDELINES
Proper Belt maintenance is essential for maximum
performance and safety:
• Store Belt loosely packed in a clean, dry environment.
• A wet Belt should be thoroughly dried before storage.
• Do not expose the Belt to direct fl ame or high temperature.
• Do not expose the Belt to chemicals or damaging substances.
• Belt may be hand washed in cool water. Use clear water or non detergent
cleanser, and rinse thoroughly.
Inspect Belt before and after each use, paying special
attention to load bearing buckles and components.
Inspection criteria should be established by the user
according to his needs, and must consider at least the
following hazards:
• Missing or torn components.
• Improperly functioning buckles or attachment points.
• Webbing and/or stitching that shows excessive wear.
• Chemical damage or exposure.
• Heat damage.
• Belt should be allocated to single user.
• Adjust the Belt as necessary to perform properly with different clothing.
• Keep Belt from contact with harsh chemical or corrosive substances.
• Avoid excessive abrasion.
• Compatibility with other equipment must be verifi ed by user.
• Repair or modifi cation of this product without manufacturer’s expressed
written consent is strictly forbidden.
INSTRUCTIONS
• Wear the Belt over uniform clothing as appropriate.
• Connect the small snap hook (sewn to the waist belt) to the V shaped
adjustable buckle over the waist belt webbing.
• Pull or loosen the tail of the webbing to attain a secure and comfortable
fi t.
• Belt must be worn snug around the waist to provide the best security.
• Excess webbing must be tucked out of the way with the elastic loop on the
belt.
• The orange lanyard with the large Snap Hook is designed as the primary
connection point. Connect this Snap Hook to suitable anchor up to 5/8”
diameter.
• User must ensure that the anchorage is appropriately located and
suffi ciently strong to prevent the wearer from falling.
• The Belt can be rotated around the waist to position the tether to ensure
appropriate fall protection.
• For maximum protection, keep the orange tether unobstructed between the
anchorage and the wearer.
• When not in use, it is advised to clip the large snap hook at the end of
the orange lanyard to one of the D-rings. Never connect a lanyard or the
like between the belt’s tether and the anchor since the greater length may
allow a fall.
The two D-ring buckles on each side of the orange lanyard are
designed as secondary attachment points for additional anchorage
straps, lanyards, etc.
• As a general rule, use them only in addition to the primary attachment
lanyard and large snap hook.
• It is the user’s responsibility to ensure that any equipment attachment to
these D-rings is compatible with the size of the D-ring and will provide the
needed support.
CERTIFIED NFPA 1983 2006, Ladder Belt
WEBV1-0411
PMI LIMITED WARRANTY
PMI products are warranted to the original retail purchaser to be free from defect in material and workmanship for a period of one year. PMI will repair or replace the item without charge provided
inspection at our factory discloses no misuse or alteration, which, in our judgment, has affected the condition or functioning of the product. All implied warranties imposed by law in connection with the sale
of PMI products are also limited in duration to a period of one year. PMI expressly excludes and shall not be liable for any consequential damages arising out of any breach of the express or implied
warranties on sales of PMI products. Because of the high risks involved in high angle rope work such as, but not limited to, rescue, rope access, caving, rappelling, rock climbing and mountaineering, no further
warranties exist or are implied by PMI. Regulations issued under the Magnuson-Moss Warranty Act require us to include the following statement: some states do not allow limitations on how long an implied
warranty lasts nor the excluding or limitation of incidental or consequential damages, so the above limitations may not apply to you.
CAUTION
Inspect Belt upon receipt to ensure that it has not been damaged
during shipment and to verify that the buckles are working properly.
WARNING
Failure to comply with these instructions and information contained
in this booklet may result in injury and death.

For additional information about this or other PMI products, contact us.
Pigeon Mountain Industries, Inc.
PO Box 803
LaFayette, GA 30728
Toll Free: 888.764.1437
Phone: [phone]
Fax: [phone] or 706.764.1531
Email: [e-mail]
Web: www.pmirope.com
Equipment Inspection Log
Item: Model #
Size:
Date Use or Maintenance Comments Name
ADDITIONAL INFORMATION
REMOVAL FROM SERVICE
Remove the Belt from service and destroy if it does not
pass inspection or if there is any doubt about the safety
or serviceability of the Belt. If any of the following
conditions are true, the Belt must be discarded:
• If the Belt has sustained a signifi cant fall (ie: fall factor 1 or greater).
• If the load bearing components of the Belt are damaged in any way.
• If the stitching shows excessive wear, is cut, or is otherwise affected in a
way that might affect Belt function or performance.
• If buckles or attachment points do not function properly, or show signs of
excessive wear or damage that might affect Belt performance.
• If the Belt has been visibly damaged by heat, chemical or other hazardous
condition.
• If the Belt has been in use for 5 years, regardless of condition.
WARNING
Proper training is required before use. Read these user instructions
and retain them as a permanent record, and maintain a copy with
the Belt along with the product use and care record. A use and care
record should be established and maintained by the purchaser or
user of the Life Safety Belt according to their needs, and should
include records specifi c to the Belt. Specifi c information to note
would include date of purchase; date put into service; maintenance
and inspection records. Refer to this information before and after
each use. The user of this equipment assumes all responsibilities
associated with its use.
WARNING
• YOU COULD BE KILLED OR SERIOUSLY INJURED IF YOU DO NOT READ
AND UNDERSTAND THIS BOOKLET BEFORE USING PRODUCT.
• SPECIAL TRAINING AND KNOWLEDGE ARE REQUIRED TO USE THIS
PRODUCT.
• YOU MUST THOROUGHLY READ AND UNDERSTAND ALL
MANUFACTURERS INSTRUCTIONS BEFORE USE.
• USE AND INSPECT THIS PRODUCT ONLY IN ACCORDANCE WITH THE
MANUFACTURERS INSTRUCTIONS.
• YOU CAN CONTACT THE MANUFACTURER AT 706-764-1437 FOR
IMPORTANT SAFETY INFORMATION.