Polaris 2884764 User manual

BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
APPLICATION
Verify accessory fitment at www.polaris.com.
KIT CONTENTS
REF QTY PART DESCRIPTION P/N AVAILABLE
SEPARATELY
AVAILABLE
SERVICE KIT
1 1 Mount Plate 1026122 n/a
2 1 Mid Mount 1026123 n/a
3 1 Bracket-Bumper Support, Upper 5265124 n/a
4 1 Handle Lock n/a n/a
5 1 Tightening Plate n/a n/a
6 1 Fairlead Adapter Plate n/a n/a
71 Lower Side Support Bracket n/a n/a
8 1 Kickstand Lever n/a n/a
Instr 9931129 Rev 01 2020-08 Page 1 of 8
P/N 2884764
PLOW MOUNT KIT

Instr 9931129 Rev 01 2020-08 Page 2 of 8
REF QTY PART DESCRIPTION P/N AVAILABLE
SEPARATELY
AVAILABLE
SERVICE KIT
9 1 Weldment Plate n/a 2208483
10 6 Screw–Hexflange, M8 x 1.25 x 25 n/a 2208483
11 2 Screw–Hexflange, M6 x 1.0 x 30 n/a 2208483
12 2 Screw–Hexflange, M10 x 1.25 x 25 n/a 2208483
13 2 Screw–Hex, M10 x 1.5 x 25 n/a 2208483
14 6 Nut–Flange, Nylon Locking, M8 x 1.25 n/a 2208483
15 2 Washer–10.5 x 20 x 2 n/a 2208483
16 2 Washer–10.2 x 18.1 x 2.2 n/a 2208483
17 2 Split Pin n/a 2208483
18 1 Pin n/a 2208483
19 1 Lock Pin n/a 2208483
20 1 Clevis Pin 16mm x 40mm n/a 2208483
21 1 Clevis Pin 9.87mm x 28mm n/a 2208483
22 1 Winch Link–Mid Size n/a 2205057
23 1 Nut–Nylon Locking, M10 x 1.5 n/a 2205057
TOOLS REQUIRED
• Safety Glasses
• Socket Set, Metric
• Wrench Set, Metric
• Socket Set, Torx®Bit
• Pliers, Needle Nose
• Torque Wrench
IMPORTANT
Your Plow Mount Kit is exclusively designed for your vehicle. Please read the installation instructions thoroughly
before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a
satisfactory installation, perform all installation steps correctly in the sequence shown.
INSTALLATION INSTRUCTIONS
VEHICLE PREPARATION
GENERAL
1. Shift vehicle transmission into Park.
2. Turn key to OFF position and remove from vehicle.
CENTER HOOD PANEL REMOVAL
1. Turn quarter-turn fasteners to unlock hood from
vehicle.

Instr 9931129 Rev 01 2020-08 Page 3 of 8
2. Move hood forward to remove from vehicle.
ACCESSORY INSTALLATION
1. Remove and keep two screws A. Remove winch
cover.
2. Remove and keep eight screws Bto remove front
fascia.
3. Disconnect headlight connectors and accent light
connectors.
4. Install upper bumper bracket support eusing
screws dand weldment plate o.

Instr 9931129 Rev 01 2020-08 Page 4 of 8
5. Install fairlead.
• If fairlead uses standard mounting holes then
install winch fairlead onto mounting plate using
screws aand nuts g.
• If fairlead uses inner holes then fairlead adapter
is required. Install fairlead and fairlead adapter
yto mounting plate using screws aand nuts
g.
6. Install mounting plate wusing screws aand nuts
g.
7. Install tightening plate twith washers hand j
and screws f.
8. Torque screws a,d, and fto specification.
TORQUE
40 ft-lbs (54 N·m)
VEHICLE REASSEMBLY
GENERAL
1. Reconnect four light connectors.

Instr 9931129 Rev 01 2020-08 Page 5 of 8
2. Install front fascia with six screws B.
3. Install two screws s.
4. Install optional winch cover with screws A
CENTER HOOD PANEL INSTALLATION
1. Move hood rearward.
2. Turn quarter-turn fasteners to lock hood to vehicle.

Instr 9931129 Rev 01 2020-08 Page 6 of 8
OPERATION
HOOK UP ASSEMBLY
1. Attach plow hookup.
2. Insert pins C.
3. Insert split pins and bend to secure.
4. Install winch link 2@ into plow assembly.
5. Attach winch to winch link.
IMPORTANT
The first adjustment requires kickstand height
adjustment, depending on ground clearance. It may
be necessary to repeat this exercise if accessories
are added that affect ground clearance.
NOTICE
If vehicle height is too low, vehicle height may
require adjustment. Refer to owner's manual for
suspension adjustment procedures.
DISCONNECTING THE PLOW ASSEMBLY
1. Lower plow onto ground using winch until there is
no tension in cable.
2. Disconnect winch from winch link.
3. Lower kickstand until it locks. Kickstand shoe
should not touch the ground. If it is refer to
Kickstand Adjustment.

Instr 9931129 Rev 01 2020-08 Page 7 of 8
4. Pull up on handle.
5. Turn assembly away from vehicle.
6. Back vehicle in a straight line until push-frame
assembly is not touching vehicle.
CONNECTING THE PLOW ASSEMBLY
1. Align vehicle with assembly. Make sure pins are
lined up with opening on the push-frame assembly.
2. Drive forward until vehicle is fully engaged in
attachment plates on both sides.
3. Rotate assembly up by hand until hook engages
with upper mount of plow mount plate. If hook
does not fully engage check for snow and ice
accumulation on lower pins of the mount plate.
The kickstand should be off of the ground. If it is
not refer to Kickstand adjustment.
4. Connect winch hook to winch link.
5. Lift plow assembly with winch until kickstand is
retracted automatically. Plow should be in top 1/3
of its travel.
WINCH LINK ADJUSTMENT
CAUTION
The plow could become disconnected during
adjustment. Always lower plow to the ground when
making adjustments to avoid injury.
1. Attach plow assembly to vehicle and connect
winch cable to winch link.
2. Raise plow until winch auto stop engages or winch
hook contacts fairlead.
3. Lift up blade by hand to determine if it is at
maximum lift height.
4. Adjust winch link so plow is at maximum lift height
when winch auto stop engages or the winch hook
contacts fairlead.

Instr 9931129 Rev 01 2020-08 Page 8 of 8
5. Lower plow to the ground and adjust nut on bottom
of winch link as required.
6. Repeat steps until maximum lift height is achieved.
KICKSTAND ADJUSTMENT
CAUTION
The plow could become disconnected during
adjustment. Always lower plow to the ground when
making adjustments to avoid injury.
The kickstand must support push frame so the
opening of push frame assembly lines up with mount
plate pins for easy installation and removal of plow
assembly.
1. Loosen jam nut Dand screw kickstand shoe up
or down to achieve desired height.
2. Check height to make sure hook up openings and
mount plate pins are aligned.
3. Tighten jam nut to secure kickstand in place.
NOTICE
It may be necessary to install jam nut on opposite
side of kickstand if additional adjustment is required.
ADJUSTMENT OF AUTO RETRACTING
KICKSTAND
CAUTION
The plow could become disconnected during
adjustment. Always lower plow to the ground when
making adjustments to avoid injury.
The auto retracting kickstand should be triggered
when cap of J-Rod makes contact with kickstand lever
of machine. This should take place in last 1/3 of
plow’s travel. Follow the steps below if kickstand fails
to release properly:
1. Make sure plow is achieving its maximum lift
height by lifting up on blade to make sure plow is
against stops at full lift. If it does not, refer to Winch
Link Adjustment.
2. Loosen jam nut on bottom of cap and screw cap in
or out to achieve desired adjustment.
3. Test kickstand assembly by putting kickstand
down and lifting plow system with winch to it’s max
lift height.
4. Repeat process until kickstand releases in top 1/3
of plow’s travel.
5. Tighten jam nut to secure cap in place.
INSTRUCTION FEEDBACK FORM
A feedback form has been created for the installer to provide any comments,
questions or concerns about the installation instructions. The form is viewable on
mobile devices by scanning the QR code or by clicking HERE if viewing on a PC.