Polycom SpectraLink 6000 System User manual

July 2008 Edition
1725-36127-001
Version F
Installing the Outdoor
Base Station
SpectraLink 6000 System

Installing the Outdoor Base Station
1725-36127-001-F.doc
2
Trademark Information
Polycom® and the logo designs
SpectraLink®
LinkPlus
Link
NetLink
SVP
Are trademarks and registered
trademarks of Polycom, Inc. in the
United States of America and various
countries. All other trademarks used
herein are the property of their
respective owners.
Patent Information
The accompanying product is protected
by one or more US and foreign patents
and/or pending patent applications held
by Polycom, Inc.
Copyright Notice
Copyright © 1998 to 2008 Polycom,
Inc.
All rights reserved under the
International and pan-American
copyright Conventions.
No part of this manual, or the software
described herein, may be reproduced or
transmitted in any form or by any
means, or translated into another
language or format, in whole or in part,
without the express written permission
of Polycom, Inc.
Do not remove (or allow any third party
to remove) any product identification,
copyright or other notices.
Every effort has been made to ensure
that the information in this document is
accurate. Polycom, Inc. is not
responsible for printing or clerical
errors. Information in this document is
subject to change without notice and
does not represent a commitment on the
part of Polycom, Inc.
Notice
Polycom, Inc. has prepared this
document for use by Polycom personnel
and customers. The drawings and
specifications contained herein are the
property of Polycom and shall be neither
reproduced in whole or in part without
the prior written approval of Polycom,
nor be implied to grant any license to
make, use, or sell equipment
manufactured in accordance herewith.
Polycom reserves the right to make
changes in specifications and other
information contained in this document
without prior notice, and the reader
should in all cases consult Polycom to
determine whether any such changes
have been made.
No representation or other affirmation of
fact contained in this document
including but not limited to statements
regarding capacity, response-time
performance, suitability for use, or
performance of products described
herein shall be deemed to be a warranty
by Polycom for any purpose, or give rise
to any liability of Polycom whatsoever.
Contact Information
Please contact your Polycom Authorized
Reseller for assistance.
Polycom, Inc.
4750 Willow Road,
Pleasanton, CA 94588
http://www.polycom.com

1725-36127-001-F.doc 3
About this Guide
The Outdoor Base Station is designed to withstand environmental
hazards such as rain and excessive heat and cold. The outdoor
enclosure is mounted into position and the Base Station is then
installed within it. The entire unit is then referred to as an Outdoor
Base Station.
This document covers the installation of the Outdoor Base Station
in a variety of situations. It supplements the installation
documentation for the SpectraLink 6000 System using either the
SpectraLink 6300 MCU or the SpectraLink 6100 MCU.
Polycom Corporation Model Numbers
This document covers the following registered model numbers:
RCO400, RCO410, RHO400
Related Documents
SpectraLink 6100 MCU: Installation and Operation (1725-36097-001)
SpectraLink 6300 MCU: Installation (1725-36122-001)
Available at
http://www.polycom.com/usa/en/support/voice/proprietary_
wireless/proprietary_wireless.html
Contacting Polycom
Polycom wants every customer to have a successful installation.
Please refer questions to the Customer Support Hotline at
[phone]. The hotline is open Monday through Friday,
6 a.m. to 6 p.m. Mountain time.

Installing the Outdoor Base Station
1725-36127-001-F.doc
4
For Technical Support: [email protected]
For Knowledge Base:
http://www.polycom.com/usa/en/support/voice/voice.html
For Return Material Authorization: [email protected]

1725-36127-001-F.doc
5
Contents
0About this Guide ................................................3
Polycom Corporation Model Numbers 3
Related Documents 3
Contacting Polycom 3
1Installing Flush Against a Wall or Hard Ceiling ....6
2Installing on an I-Beam.......................................8
3Installing on a Light Pole or Electrical Pole .........10

1725-36127-001-F.doc
6
Installing Flush Against a Wall
or Hard Ceiling
Items provided: Outdoor enclosure, Base Station
Items needed: 4 anchor bolts (length and type depends on
wall or ceiling material Base Station is being
mounted to)
1. Mark and drill four holes into the wall or ceiling, using the
mounting flanges of the outdoor enclosure as a guide.
2. Mount outdoor enclosure to wall or ceiling using anchor bolts.
The outdoor enclosure can be mounted with the compression
fitting in any direction.
3. Slide the Base Station cable through the compression fitting
and tighten fitting.
Compression
fittin
g
1

Installing Flush Against a Wall or Hard Ceiling
1725-36127-001-F.doc
7
4. Crimp an RJ45 onto the Base Station cable using the same
wiring guide as the indoor Base Station.
5. Plug the RJ45 into the RJ48C connector.
6. Place the Base Station into the enclosure with the side of the
Base Station with the mounting hole facing the wall or ceiling.
The Base Station should fit tightly into the foam blocks.
7. Screw the outdoor enclosure lid back onto the enclosure.
RJ48C
connector
Mounting
hole

1725-36127-001-F.doc
8
Installing on an I-Beam
Items provided : Outdoor enclosure, Base Station
Items needed : 4 – “Caddy” or “B-Line” 3/8” Beam Clamps
4 – 1/2” long 1/4” x 20 bolts
4 – 2” long 1/4” x 20 bolts
4 – 1/4” x 20 nuts
1. Attach a beam clamp to the center of the top and bottom
flanges on the outdoor enclosure.
2. Attach a second beam clamp to each of the beam clamps on the
enclosure using a 1/2” long 1/4” x 20 bolt and a nut. (See
figure below.)
3. Attach the outdoor enclosure to I-beam using the beam clamps
attached in step 2.
See figures in Chapter 1 for pictorial data for the remaining steps:
4. Slide the Base Station cable through the compression fitting
and tighten the fitting.
5. Crimp on RJ45 onto the Base Station cable using the same
wiring guide as the indoor Base Station.
6. Plug the RJ45 into the RJ48C connector.
2

Installing on an I-Beam
1725-36127-001-F.doc 9
7. Place the Base Station into the enclosure with the side of the
Base Station with the mounting hole facing the I-beam. The
Base Station should fit tightly between the foam blocks.
8. Screw the outdoor enclosure lid back onto the enclosure.

1725-36127-001-F.doc
10
Installing on a Light Pole or
Electrical Pole
Items provided: Outdoor enclosure, Base Station
Items needed: 4 - “Caddy” or “B-Line” 3/8” beam clamps
2 - EOG 100 or equivalent band clamps
1. Attach one band to the top flange of the outdoor enclosure
using two beam clamps (see the figure below).
2. Attach the second band to the bottom flange of the enclosure
using the remaining two beam clamps.
3. Wrap the band clamps around the pole and tighten using the
screw on the band clamps.
See figures in Chapter 1 for pictorial data for the remaining steps:
4. Slide the Base Station cable through the compression fitting
and tighten the fitting.
5. Crimp an RJ45 onto the Base Station cable using the same
wiring guide as the indoor Base Station.
6. Plug the RJ45 into the RJ48C connector.
3