Precor Queenax UFO User manual

Page 1 of 3
QUEENAX ASSEMBLY BULLETIN
AB.QX.20170630
Contact Precor customer support at [email protected] or 800.786.8404 with any questions.
©2017 Precor Incorporated, Unauthorized reproduction and distribution prohibited by law. Page 1 of 3
Queenax UFO assembly
UFO
The UFO is a suspended platform that is designed to enhance motor
control, balance, rhythm, body awareness, mental engagement and
strength. The UFO's four anchor points accommodate suspended
bodyweight training in 360 degrees. Users can sit, stand or kneel on the
UFO or position just the arms and legs on it, allowing for a variety of
exercise possibilities.
UFO location
The UFO is best mounted in the open space centered between two
training bars. Depending on configuration and space available, the
UFO can also be mounted centered on a single training bar.
UFO bracket assembly
The UFO hangs from four mounting brackets that are attached
to the horizontal beam (see Exploded view below).
1. Mount each bracket loosely to the beam. Space the brackets
30 cm apart (2 open holes in between brackets). If space is
constrained the brackets can be mounted 40 cm or 50 cm (3
or 4 open holes in between brackets) apart.
2. Insert the Cross Bars.
3. Attach the Strap Guards.
4. Fully tighten all hardware.
5. Tighten the four set screws that secure the Cross Bars.
6. Inflate and setup UFO (see UFO setup steps below).

Page 2 of 3
QUEENAX ASSEMBLY BULLETIN
AB.QX.20170630
Contact Precor customer support at [email protected] or 800.786.8404 with any questions.
©2017 Precor Incorporated, Unauthorized reproduction and distribution prohibited by law. Page 2 of 3
Exploded view and parts list
Item
QTY
Description
1
4
SCREW, FHC, M10X1.5X30, STL, CZ
2
4
SCREW, SET, HEX SOCKET, M10 1.25X10, STL, BZ
3
8
NUT, LOCK, FULL, M10X1.5, NYLON INSERT, STL, CZ
4
8
SCREW, BHC, M10 1.5X40, STL, ZN, BZ
5
8
WASHER, FLAT, STEEL, M10 X 2.0mm THICK, BZ
6
8
WASHER, FLAT, STEEL, M10 X 40 OD X 2.5T, CZ
7
4
WELDMENT, UFO BRACKET
8
2
CROSS BAR, UFO BRACKET
9
4
O RING, 23.7 ID X 3.5mm WIDTH, BUNA-N
10
4
STRAP GUARD, OUTER, CROSS BAR
11
4
STRAP GUARD, INNER, CROSS BAR

Page 3 of 3
QUEENAX ASSEMBLY BULLETIN
AB.QX.20170630
Contact Precor customer support at [email protected] or 800.786.8404 with any questions.
©2017 Precor Incorporated, Unauthorized reproduction and distribution prohibited by law. Page 3 of 3
UFO setup
Inflation
Use the included pump and valve adaptor to
inflate the UFO to approximately 18 PSI (120
kPA). UFO should be firm and have almost no
flex or bend when a user is standing on it.
Suspension
1. Secure the UFO bands onto the loops on the
bottom.
2. Run four Superfunctional straps though
the four outside loops (strap numbers
should face outward.
3. Connect strap #9 of the Superfunctional strap to
the UFO band.
4. Hang the four Superfunctional bands
from the UFO bracket.
5. Place one Superfunctional bar in front and one in
back for user balance control.