Q5X CoachMic QT-AD10C User manual
DOCID-M-0010-9.0
Digital CM
QT-AD10C Quick Start Guide
Next Steps
Check you included hardware
against the quickstart guide.
Visit www.Q5X.com/support
Update the rmware.
Register the warranty.
Download digital manuals and
addional resources.
Have quesons?
We’re listening.
| www.Q5X.com | inf[email protected] | 519-675-6999 |
| www.Q5X.com | in[email protected]om | 519-675-6999 |
User Tips:
When using the CoachMic, the belt clips can be
congured to wear the transmier horizontally on the
le or right side of the body, or vercally in a pocket.
The mute funcon can be controlled by either the
integrated rocker switch or wirelessly by the Gateway.
Q5X Support
Scan here to visit our online
support and get access to FAQ,
rmware updates, warranty
registraon, and more.
Quick Start Guide Digital CMQT-AD10C
This Quick Start Guide is an overview. Users are asked to
review the enre manual for detailed instrucons
Included Hardware:
• Carrying pouch.
• Digital CoachMic transmier (QT-AD10C).
• Micro USB charging cable.
Users Also Need:
• Q5X Gateway (remote control)
• Handheld MicCommander (QG-H2) or
• Network Gateway (QG-N3).
• Shure Axient Digital receiver.
• Microphone (1-pin Lemo connector).
:
65.5mm x 42mm x 18.5mm
:
8 hours @ 2/10mW 4 hours @ 20mW
Bring the transmier out of storage mode (minimal baery
draw) and into standby mode (detectable but the UHF radio
is o) using either method below:
• Hold the ON/OFF buon unl the status LED changes
from ashing rapidly to slowly, or
• Plug and unplug a powered micro USB charging cable
into the side of the transmier.
• Connect the 1-pin Lemo microphone.
:
• Install the antennas on the top. (NEVER power the unit
without the antenna in place.)
• Power the Gateway as instructed in its manual.
Turn on the unit by pressing the power buon.
:
• The screen on the Gateway displays the serial number of
paired transmiers.
• Press the <MENU> buon to either scan for transmiers or
add the serial number on the back of the AquaMic.
Adjust:
• Set the funcons in the two transmier menus of the
Gateway.
• Screen one includes frequency, power On/O, baery
level, mic mute/live and mic oset.
• Screen two includes: transmier name, group, RF power,
2.4GHz channel, storage and reboot.
:
• Use IR Sync to form an audio channel between the
transmier and receiver.
• The receiver band must match the band of the transmier.
• Select a receiver channel.
• Tune the channel to an available frequency using group
scan or manually tune to an open frequency.
• Assure transmier is in standby or ON mode. Press the
SYNC buon on the receiver.
• Align the IR windows between the transmier and the
receiver so that the IR LED illuminates red. When complete,
“Sync Success!” appears on the receiver.
Hardware Diagram:
:
1. 2.4 G antenna: For the RCAS control channel.
2. Audio input: Connects to a waterproof microphone
with a 6-pin Lemo connector.
UHF antenna: For RF signal transmission.
4. Serial number: The unique number for RCAS ID and
control is on the back of the AquaMic.
5. port: Infrared sync with the receiver for set-up,
iniang encrypon and installing rmware updates.
6. Status: See manual for details on LED paerns
and colours.
7. Charge: Red = charging, green = charged and
ashing red/green = error.
8. Charging port: AquaMic charges through the same
connector as the audio input using the charge dongle.
9. On: There is no manual power
control buon on the AquaMic to maintain the
waterproof seal.
10. Belt clip holes: Allows vercal and horizontal
placement.
3
2
1
4
7
6
9
5
10
810
11
Other Q5X Transmitter manuals
