Q5X AquaMic QT-5100A User manual

DOCID-M-010-1.0
Next Steps
Check you included hardware
against the quickstart guide.
Visit www.Q5X.com/support
Register the warranty.
Download digital manuals and
addional resources.
Have quesons?
We’re listening.
| www.Q5X.com | [email protected]om | 519-675-6999 |
| www.Q5X.com | [email protected]om | 519-675-6999 |
Q5X Support
Scan here to visit our online
support and get access to FAQ,
rmware updates, warranty
registraon, and more.
AM
QT-5100A (AL) Quick Start Guide

Quick Start Guide AMQT5100A (AL)
This Quick Start Guide is an overview. Users are asked
to review the enre manual for detailed instrucons
Included Hardware:
• Carrying pouch.
• Digital AquaMic (QT-5100A or AL).
• SSMA Antennas (2.4 GHz and UHF) .
• Charging dongle (6-pin Lemo to Micro USB).
• Charging cable.
• Reset key.
Users Also Need:
• Q5X Gateway (remote control)
• Handheld MicCommander (QG-H2).
• Network Gateway (QG-N3).
• Analog receiver.
• Microphone (6-pin Lemo connector).
Prepare the AquaMic:
• Connect the antennas to the labelled ports.
Bring the transmier out of storage mode (minimal
baery draw) and into standby mode (detectable but the
UHF radio is o) by using the charging dongle screwed
into the charging port on end of the AquaMic.
• Plug and unplug a powered micro USB charging cable
into the charging dongle.
• Replace the dongle with the 6-pin Lemo microphone.
Do not over ghten the microphone or antenna beyond
nger ght to avoid damaging the o-rings.
Prepare the Gateway Remote Control (H2 or N3):
• Install the antennas on the top. (NEVER power the
unit without the antenna in place.)
• Power the Gateway as instructed in its manual.
• Turn on the unit by pressing the power buon.
Prepare AquaMic & Gateway Remote Control:
• The screen on the Gateway displays the serial
number of paired transmiers.
• Press the <MENU> buon to either scan for
transmiers or add the serial number on the back of
the AquaMic.
Adjust:
• Set the funcons in the two transmier menus of the
Gateway.
• Screen one includes frequency, power On/O,
baery level, mic mute/live and mic oset.
• Screen two includes: transmier name, group, RF
power, 2.4GHz channel, storage and reboot.
Dimensions:
AquaMic: 65mm x 46mm x 19mm
AquaMic L: 65mm x 46mm x 22.5mm
:
AquaMic 8 Hours @ 50mw 4 Hours @ 100mw
AquaMic L 16 Hours @ 50mw 8 Hours @ 100mw
Hardware Diagram:
Key:
1. 2.4 G antenna: For the RCAS control channel.
2. Audio input: Connects to a waterproof
microphone with a 6-pin Lemo connector.
3. UHF antenna: For RF signal transmission.
4. Serial number: The unique number for RCAS ID
and control is on the back of the AquaMic.
5. N/A
6. Status LED: See manual for details on LED
paerns and colours.
7. Charge LED: Red = charging, green = charged
and ashing red/green = error.
8. Charging port: AquaMic charges through the
same connector as the audio input using the
charge dongle.
9. On: There is no manual power
control buon on the AquaMic to maintain the
waterproof seal.
10. Belt clip holes: Allows vercal and horizontal
placement.
1
10
2/8
3
10
10
10
7
6
User Tips:
The AquaMic is IP68 Cered waterproof
to 100  (30.5 m).
All connectors should be nger ght,
audio quality and RF performance maybe
be impacted if water is able to penetrate
into a loose-ng connector.
To keep the AquaMic in top condion,
rinse the AquaMic with fresh water aer
use, especially if used in saltwater.