Q5X PlayerMic User manual

DOCID-M-0010-8.0
Digital PM
QT-AD10P (PS) Quick Start Guide
Next Steps
Check you included hardware
against the quickstart guide.
Visit www.Q5X.com/support
Update the rmware.
Register the warranty.
Download digital manuals and
addional resources.
Have quesons?
We’re listening.
| www.Q5X.com | inf[email protected] | 519-675-6999 |
| www.Q5X.com | in[email protected]om | 519-675-6999 |
User Tips:
When using the PlayerMic, it is suggested that a strain
relief method be used to ensure that there is no direct
pulling force on the microphone connector during
use or during removal. One method is to loop the
microphone cable back and tape the connector to the
edge of the transmier.
Q5X Support
Scan here to visit our online
support and get access to FAQ,
rmware updates, warranty
registraon, and more.

Quick Start Guide Digital PM QT-AD10P (PS)
This Quick Start Guide is an overview. Users are asked to
review the enre manual for detailed instrucons
Included Hardware:
• Carrying pouch.
• Digital PlayerMic transmier (QT-AD10P or PS).
• Micro USB Charging cable.
Users Also Need:
• Q5X Gateway (remote control)
• Handheld MicCommander (QG-H2) or
• Network Gateway (QG-N3).
• Shure Axient Digital receiver.
• Microphone (1-pin Lemo connector).
:
PlayerMic S: 74.5mm x 42mm x 11.5mm
PlayerMic: 97.5mm x 42mm x 11.5mm
:
PlayerMic S 4 hrs @ 2/10mW 2 hrs @ 20mW
PlayerMic 8 hrs @ 2/10mW 4 hrs @ 20mW
:
Bring the transmier out of storage mode (minimal baery
draw) and into standby mode (detectable but the UHF radio
is o) using either of the following methods.
• Hold the ON/OFF buon unl the status LED changes
from ashing rapidly to slowly, or
• Plug and unplug a powered micro USB charging cable
into the side of the transmier.
• Connect the 1-pin Lemo microphone
Prepare the Gateway remote control (H2 or N3):
• Install the antenna on the top. (NEVER power the unit
without the antenna in place.)
• Power the Gateway as instructed in its manuals.
• Turn on the unit by pressing the power buon.
Pair the PlayerMic and Gateway remote control:
• The screen on the Gateway displays the serial number of
paired transmiers.
• Press the <MENU> buon to either scan for transmiers or
add the serial number found on the PlayerMic antenna.
Adjust:
• Set the funcons in the two transmier menus of the
Gateway.
• Screen one includes frequency, power On/O, baery
level, mic mute/live and mic oset.
• Screen two includes: transmier name, group, RF power,
2.4GHz channel, storage and reboot.
IR Sync:
• Use IR Sync to form an audio channel between the
transmier and receiver. The receiver band must match
the band of the transmier.
• Select a receiver channel.
• Tune the channel to an available frequency using group
scan or manually tune to an open frequency.
• Assure transmier is in standby or ON mode.
• Press the SYNC buon on the receiver.
• Align the IR windows between the transmier and the
receiver so that the IR LED illuminates red.
• When complete, “Sync Success!” appears.
Hardware Diagram:
Key:
1. 2.4 G antenna: For the RCAS control channel.
2. Audio input: Connects to a waterproof microphone
with a 6-pin Lemo connector.
3. UHF antenna: For RF signal transmission.
4. Serial number: The unique number for RCAS ID and
control is on the back of the AquaMic.
5. IR port: Infrared sync with the receiver for set-up,
iniang encrypon and installing rmware updates.
6. Status: See manual for details on LED paerns
and colours.
7. Charge: Red = charging, green = charged and
ashing red/green = error.
8. Charging port: AquaMic charges through the same
connector as the audio input using the charge dongle.
9. On: There is no manual power
control buon on the AquaMic to maintain the
waterproof seal.
8
6
5
94
3
2
1
7