Q5X AquaMic QT-AD10A User manual
DOCID-M-010-7.0
Digital AM
QT-AD10A (AL) Quick Start Guide
Next Steps
Check you included hardware
against the quickstart guide.
Visit www.Q5X.com/support
Update the rmware.
Register the warranty.
Download digital manuals and
addional resources.
Have quesons?
We’re listening.
| www.Q5X.com | inf[email protected] | 519-675-6999 |
| www.Q5X.com | in[email protected]om | 519-675-6999 |
User Tips:
The AquaMic is IP68 Cered waterproof to 100
(30.5 m).
All connectors should be nger ght, audio quality and
RF performance maybe be impacted if water is able to
penetrate into a loose-ng connector.
To keep the AquaMic in top condion, rinse the
AquaMic with fresh water aer use, especially if used
in saltwater.
Q5X Support
Scan here to visit our online
support and get access to FAQ,
rmware updates, warranty
registraon, and more.
Quick Start Guide Digital AM QT-AD10A (AL)
This Quick Start Guide is an overview. Users are asked to
review the enre manual for detailed instrucons
Included Hardware:
• Carrying pouch.
• Digital AquaMic transmier (QT-AD10A or AL).
• SSMA Antennas (2.4 GHz and UHF) .
• Charging dongle (6-pin Lemo to Micro USB).
• Charging cable.
• Reset key.
Users Also Need:
• Q5X Gateway (remote control)
• Handheld MicCommander (QG-H2) or
• Network Gateway (QG-N3).
• Shure Axient Digital receiver.
• Microphone (6-pin Lemo connector).
:
AquaMic: 65mm x 46mm x 19mm
AquaMic L: 65mm x 46mm x 22.5mm
:
AquaMic 8 hrs @ 2/10 mW 4 hrs @ 20 mW
AquaMic L 16 hrs @ 2/10 mW 8 hrs @ 20 mW
Prepare the AquaMic:
• Connect the antennas to the labelled ports.
Bring the transmier out of storage mode (minimal baery
draw) and into standby mode (detectable but the UHF
radio is o) by using the charging dongle screwed into the
charging port on end of the AquaMic.
• Plug and unplug a powered micro USB charging cable
into the charging dongle.
• Replace the dongle with the 6-pin Lemo microphone.
• Do not over ghten the microphone or antenna beyond
nger ght to avoid damaging the o-rings.
:
• Install the antennas on the top. (NEVER power the unit
without the antenna in place.)
• Power the Gateway as instructed in its manual.
• Turn on the unit by pressing the power buon.
:
• The screen on the Gateway displays the serial number of
paired transmiers.
• Press the <MENU> buon to either scan for transmiers or
add the serial number on the back of the AquaMic.
Adjust:
• Set the funcons in the two transmier menus of the
Gateway.
• Screen one includes frequency, power On/O, baery
level, mic mute/live and mic oset.
• Screen two includes: transmier name, group, RF power,
2.4GHz channel, storage and reboot.
:
• Use IR Sync to form an audio channel between the
transmier and receiver. The receiver band must match
the band of the transmier.
• Select a receiver channel.
• Tune the channel to an available frequency using group
scan or manually tune to an open frequency.
• Assure transmier is in standby or ON mode.
• Press the SYNC buon on the receiver.
• Align the IR windows between the transmier and the
receiver so that the IR LED illuminates red.
• When complete, “Sync Success!” appears on the receiver.
Hardware Diagram:
:
1. 2.4 G antenna: For the RCAS control channel.
2. Audio input: Connects to a waterproof microphone
with a 6-pin Lemo connector.
UHF antenna: For RF signal transmission.
4. Serial number: The unique number for RCAS ID and
control is on the back of the AquaMic.
5. IR port: Infrared sync with the receiver for set-up,
iniang encrypon and installing rmware updates.
6. Status LED: See manual for details on LED paerns
and colours.
7. Charge LED: Red = charging, green = charged and
ashing red/green = error.
8. Charging port: AquaMic charges through the same
connector as the audio input using the charge dongle.
9. On: There is no manual power
control buon on the AquaMic to maintain the
waterproof seal.
10. Belt clip holes: Allows vercal and horizontal
placement.
6
7
5
10
10
10
1
2/8
3
10
This manual suits for next models
1
Other Q5X Transmitter manuals
