RAB FIELD-ADJUSTABLE TOMO-2 User manual
INSTRUCTIONS
FIELD-ADJUSTABLE TOMO™ INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
1. Secure Surface Mounting Plate to Junction Box (by others).
(Additional attachment to the ceiling may be needed
for longer xtures). 8ft TOMO includes a 2nd Surface
Mounting Plate and Surface Mount Adapter Plate
(see Fig. 2).
2. Remove Silicone Plugs located on each end of the Housing
Cover as shown in Fig. 2 (do not discard Silicone Plugs).
3. Pull the End Caps
in Fig. 1. Separate the Housing Cover from the Lens and
Tray Assembly by sliding the Housing Cover either right of
left to unlock from Key Slots as shown in Fig. 3. Pre-installed
Tether Cables (2) will prevent Lens and Tray Assembly from
separating from Housing Cover (Fig. 1).
4. Pull supply wires from Junction Box (by others) through
center of Surface Mounting Plate. Use appropriate UL
rated wire connectors as required by NEC and local code
5. Align Surface Mount Adapter Plate to the Housing Cover.
Using (4) Screws (provided) secure Surface Mount Adaptor
Plate and Housing Cover to the Surface Mounting
Plate.
6. Follow appropriate wiring instructions per code (Fig. 12).
7. Push Lens and Tray Assembly into the Housing Cover.
Align Keys into Key Slots and slide to the right or left to
lock the Housing Cover into the Lens and Tray Assembly.
Snap on End Caps and insert Silicone Plugs into Housing
Cover.
WARNING: To prevent wiring damage or abrasion, do
not expose wiring to edges of sharp objects.
TOMO- 2FT
End Cap (2)
Surface Mounting Plate Housing Cover
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
The xture is suitable for indoor applications. Suitable for damp locations. Ceiling, Canopy and Pendant mount only.
SURFACE MOUNTING
Fig: 1
TOMO- 4FT TOMO- 8FT
Surface Mount Adapter Plate
Lens and Tray Assembly
Screws (4)
Tether Cable (2)
Lens and Tray Assembly
Key Slot
Housing Cover
Surface Mount Adapter Plate
Fig: 2
Fig: 3
Power Cord Knockout
Cable Coupler Knockout
Silicone Plugs (2)
INSTRUCTIONS
FIELD-ADJUSTABLE TOMO™ INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mark[email protected]
Cable
Junction Box
(sold separately)
Cross Bar
Locknut
Canopy
with Power
Cord
1/4- 20 Stud
Strain Relief
Canopy
Rings
Power Cord
Fixture
Cable Coupler
Cable Coupler Nut
Cable Coupler
Fig: 6
1. Slide Power Cord through the hole on Canopy and tighten
with Strain Relief.
2. Connect wires per NEC and local code as shown in wiring
diagram (Fig. 12). Push all wires back into the Junction Box. Be
careful not to pinch wires. Mount the Cross Bar on Junction
Box.
3. Mount the Canopy to the Junction Box. Push Cable Coupler
on the 1/4-20 Stud and tighten the Coupler.
4. Canopy and Cable without Power Cord can be mounted
with a 1/4 -20 Stud and hardware appropriate to mounting
surface.
5. Push Lens and Tray Assembly into the Housing Cover. Align
Keys into Key Slots and slide to the left to lock the Housing
Cover into the Lens and Tray Assembly. Snap on End Caps.
WARNING: To prevent wiring damage or abrasion, do
not expose wiring to edges of sharp objects.
1. Remove End Caps. Slide Lens Tray Assembly from Housing
Cover to release Tray Assembly
right to unlock from Key Slots as shown in Fig. 3. Pre-installed
Tether Cables (2) will prevent Lens and Tray Assembly from
separating from Housing Cover as shown in Fig. 1.
2. For Canopy Mounting, remove (2) Knockouts on the
Housing Cover as shown in Fig. 4.
3. Insert Cable Couplers from the inside of the Housing Cover
through the two respective Cable Coupler Knockouts as
shown in Fig. 5.
4. Secure the Cable Couplers with Cable Coupler Nuts onto the
Housing Cover as shown in Fig. 5.
5. Insert the Cable into the Cable Couplers. Adjust the length
of the Cable and tighten the Locknuts and trim any excess
6. Pull supply wires through Power Cord Knockout and make
Pass the Power Cord and Cable
through the Canopy Rings. Adjust the length of the Power
Cord and tighten it on the Canopy with Strain Reliefs (Fig. 6).
8. Mount all Canopies to the Fixture with appropriate Cable
length.
9. Follow appropriate wiring instructions per NEC and local
code (Fig. 12).
Cable
Tether Cable
Locknut
Cable Coupler Nut
Fig: 4
Knockouts
Fig: 5
INSTRUCTIONS
FIELD-ADJUSTABLE TOMO™ INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mark[email protected]
FIELD ADJUSTMENT
Color (CCT) Selection Switch
Power (W) Selection Switch
TOMO-2
TOMO-4
TOMO-8
Fig: 9
Fig: 10
Fig: 11 Power (W) Selection Switch
Color (CCT) Selection Switch
Color (CCT) Selection Switch
Power (W) Selection Switch
CONTINUOUS RUN MOUNTING
TOMO CONNECTTOMO CONNECT
(sold separately).
Note: Continuous Run Mounting is not available with
LIGHTCLOUD® /LC, /LC/E, /LCB sux.
1. End Caps (Fig. 6). Pop out
Silicone Plugs, push Fixtures together using TOMO CONNECT
(ordered separately)
installation (Fig. 7). TOMO CONNECT is provided with (2) Fixing
Screws. Install Fixing Screws in Silicone Plug points. Only (1)
one Fixture needs to be electrically hard wired from above (Fig.
8).
2. CAUTION:
linked together is indicated in table below (120V through 277V
only).
WARNING: To prevent wiring damage or abrasion, do not expose
wiring to sharp objects.
Catalog #
TOMO-2
TOMO-4
TOMO-8
Maximum Number of Linked Fixtures
Up to 28
Up to 14
Up to 7
TOMO CONNECT
Fig: 6
Fig: 7
Fig: 8
Fixing Screws
Silicone Plug
TOMO
CONNECT
Follow instColor
Temperature (CCT) and Power (W) from the factory settings.
Factory Settings: TOMO-2 18W / 4000K
TOMO-4 36W / 4000K
TOMO-8 72W / 4000K
1. Remove End Caps. Slide Lens Tray Assembly from Housing
Cover to release Tray Assembly from Housing Cover by
Key Slots as
shown in Fig. 3. Pre-installed Tether Cables (2) will prevent
Lens and Tray Assembly from separating from Housing Cover
as shown in Fig. 1.
2. Locate the selector switches inside the Lens & Tray Assembly
as shown below for TOMO-2, TOMO-4 TOMO-8 (Fig. 9, 10, 11).
Note: TOMO-8 is equipped with two (2) Color Temperature
(CCT) switches and (2) two Power (W) switches.
3. Select a Color Temperature (CCT) and Power (W) by sliding
the respective switch to the desired value.
4. After the switch is positioned to the desired setting, push Lens
and Tray Assembly into the Housing Cover. Align Keys into
Key Slots and slide to the left to lock the Housing Cover into
the Lens and Tray Assembly. Snap on End Caps.
WARNING: To prevent wiring damage or abrasion, do
not expose wiring to edges of sharp objects.
INSTRUCTIONS
FIELD-ADJUSTABLE TOMO™ INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mark[email protected]
PIR MODELS INTERNAL
See factory settings below (optional remote sold separately for custom settings, CAT# TOMO-REMOTE).
Factory Settings:
• Hold Time: 1 Minute
• Stand-by period: 1 Minute
• Stand-by dimming level: 10%
• Constant Lux: 50Lux
• Detection range: Disabled
DETECTION PATTERN
walking towards
walking across
Detection Area 20ft
10ft
INSTRUCTIONS
FIELD-ADJUSTABLE TOMO™ INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mark[email protected]
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to touch.
Do not clean or maintain while xture is energized.
1. Clean acrylic lens with non-abrasive cleaning solution.
2.
the LEDs.
TROUBLESHOOTING
Refer to wiring directions.
Note: These instructions do not cover all details or variations in equipment
nor do they provide for every possible situation during installation, operation
or maintenance.
Universal voltage driver permits operation at 120V through 277V,
50 or 60 Hz. For 0-10V dimming, follow the wiring directions as
shown in Fig. 12.
1.
2.
3.
4.
5.
6.
PINK
LIGHT
FIXTURE
Vaux 12V
YELLOW
GROUND
GROUND
( - ) DIM V
( + ) DIM V
COMMON
LINE BLACK
WHITE
PURPLE
Fig: 12
INSTRUCTIONS
FIELD-ADJUSTABLE TOMO™ INSTALLATION
RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mark[email protected]
WIRING OPERATION
MAINTENANCE
TROUBLESHOOTING
Note: These instructions do not cover all details or variations in equipment
nor do they provide for every possible situation during installation,
operation or maintenance.
LIGHT
FIXTURE
INSIDE FIXTURE
BATTERY
Pink/DIM–
Black/Switched Line
Green/Ground
White/Neutral
Black/Unswitched Line
Purple/DIM+
BACKUP
DRIVER
BATTERY
CONNECTOR:
CONNECT
ONLY AFTER
AC SUPPLY
POWER IS
CONNECTED
BATTERY BACKUP MODELS
TOMO - IN - 0823 RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly - sales@rablighting.com
Free Lighting Layouts
Answered online or by request
© 2022 RAB LIGHTING Inc.
Fig: 13
CAUTION: FOR BATTERY BACKUP FIXTURE (TOMO-4/TOMO-8)
Voltage could be present in BATTERY. To prevent high voltage
from being present on output leads, Inverter Connector must
be open. Do not join BATTERY connector until installation is
complete and AC power is supplied to the emergency driver
(Fig. 13).
NOTE: Make sure that the necessary branch circuit wiring is
available. An UNSWITCHED AC source of power is required. The
emergency driver must be fed from the same branch circuit as the
LED driver.
CAUTION: Do not use any supply voltage other than 120-277V
50/60 HZ.
1. Connect UNSWITCHED HOT HOT AC supply
line.
2. If using an UNSWITCHED circuit, connect UNSWITCHED
and SWITCHED lines together.
3. If using a SWITCHED circuit, connect SWITCHED HOT AC
xture lead to the external control.
4. For 0-10V dimming, connect DIMDIM
(-) pink lead to 0-10V dimmer connections.
5. Connect GROUND
ground. Do not connect GROUND to the output leads.
6. All unused leads must be capped and insulated.
7. After installation is complete, supply AC power to the
BATTERY (Fig. 13).
8.
Charging Indicator Light should illuminate to indicate the
battery is charging.
9. Once the BATTERY has charged for at least one hour, a
short duration test may be performed by pressing the test
button.
10. After the battery has charged for 24 hours, a long duration
1. When AC power is applied, the charging indicator light
is illuminated indicating that the BATTERY is being
charged.
2. When power fails, the standby power automatically
switches to backup mode at reduced power resulting in
lower illumination. The emergency driver supplies power
in standby mode for a minimum of 90 minutes.
3. When AC power is restored, the emergency driver
automatically returns to charging mode.
1.
2. If the charging indicator light does not illuminate after
pressing the Test Button (Fig. 14), check if battery is
connected properly.
Although no routine maintenance is required to keep the
emergency driver functional, it should be checked periodically
to ensure that it is working. The following schedule is
recommended:
1. Visually inspect the charging indicator light monthly. It
should be illuminated.
2.
intervals for a minimum of 30 seconds.
3. Conduct a 90-minute discharge test once a year. Fixture
would operate at reduced illumination for a minimum of
90 minutes.
P-100173
Fig: 14
Test Button
This manual suits for next models
2
Table of contents
Other RAB Lighting Equipment manuals
Popular Lighting Equipment manuals by other brands
Heath Zenith
Heath Zenith Wireless Lamp/Outlet Modules 6136 product manual
Qlight
Qlight ST45ML Series operating manual
HAMPTON BAY
HAMPTON BAY RS233Mb-M53-ORB-6 Use and care guide
Zero88
Zero88 FROG 2 operating manual
Expolite
Expolite Tourled MC180 user manual
FOS Technologies
FOS Technologies PIXEL BAR 18 user manual
