ramia BORA 1350 User manual

A – 18pcs B – 4pcs C – 4pcs D – 4pcs E – 4pcs F1 – 4pcs F2 – 2pcs G – 4pcs
10x40 mm M10x120 M 12 M 12 M10 6x30 mm 6x40 mm 5x60 mm
H – 6pcs I - 2pcs Glue - 1pc
5x60 mm 5x80mm
Notice: Manufacturing tolerance = +/- 2,00mm
RECOMMENDATIONS: Your workbench has NO TREATMENT. Before using the product for the first
time, we recommend treating all the wooden parts with suitable wood oil (linseed oil is best). The oil or
lacquer protects the wood and prevents the absorption of ambient moisture. Oil coating applications should be
repeated twice per year. To increase the rigidity of your workbench ensure that you glue the joints and bolt
the bench in possiton.
Wood is a natural product, check and tighten all screws and bolts every six monhts.
Hardware list:
Spindle key - 1pc
Bench dogs - 4pcs
Assembly Instructions – BORA Worktable 1350/1650
The product is made of high-quality beech and spruce wood, which guarantees a long service life and utility
value.
WARNING: The product must not be subjected to direct long-term exposure to the action of water or high
humidity, which can cause the wood to expand (warp). NEVER LEAVE the product out in the rain!!!

Number Quantity Number Quantity
1 1 pc 7 1 pc
2 1 pc 8 1 pc
3 1 pc 9 1 pcs
4 1 pc 10 2 pcs
5 2 pcs 11 1 pc
6 2 pcs 12 4pcs
Left leg
Middle stretcher (with logo)
Middle stretcher (without logo)
Name
Table top
Wooden jaw
Manual and parts list
Parts list
Name
Spindle key
Wooden jaw face
Spindle HV 515
Right leg
!!! WARNING – Wooden parts may have sharp edges!!!
MDF shelf
Worktop support
Bench dogs
5
6
1
2
4
3
7
8
9
10
11
12

Repeat the same on the 2nd legs (parts 6 + 10)
Smear the dowels and the surfaces of the wooden parts with glue and insert them into the holes. This is
very important for successful gluiing of legs
Warning: Be sure the holes on all legs have the same direction!!! Like you see on the picture.
1. Legs assembly
Repeat the same on 2nd legs and wait at least 30minutes before next steps.
Use 2 screws XY (G) to fix legs (part 5 + 6) to bench top support (part 10).
5
10
G
A +
Glue

Smear the dowels and the surfaces of the wooden parts with glue and insert them into the holes.
2. Middle stretchers and shelf assembly
9
8
7
A +
Glue
D+E
B+C

Turn the table top (1) upside down. Before installing the carpenter’s vice, decide on its location
(right/left). WARNING!!! The table top is now upside down.
Fix the wooden jaw face (part 3) with 5x80 mm screws (I) in the pre-drilled holes. Unscrew the spindle
(part 4) from the spindle body and use 6x30 mm screws (F1) to fix it to the bench top according to the
pre-drilled holes.
3. Installation of the carpenter’s vice
3
4
I
F1
3
I

On one end of the handle, fix the end with the dowel (A) and glue. Insert it into the spindle and glue the
second end on the other end. Leave to dry for at least one hour before use.
Fit the wooden jaw (part 2) on the spindle guide and rotate it onto the already installed spindle body.
4. Installation of the handle in the spindle
Fully tighten the wooden jaw (part 2) with the spindle and ensure that it is horizontal with the table top.
After this, fix the wooden jaw with 6x40 mm screws (F2) to the spindle guide.
F2
F2
A +
glue

5. Fixture of the table top
The installation is now finished and the table is ready.
H