ramia HB-DIY1500 User manual

A1-38pcs B1-20pcs B2-8pcs B3-4pcs B4-4pcs C1-4pcs D1-4pcs D2-4pcs E-4pcs F-1pcs
10x40 mm 7x60 mm 6x30 mm 6x40 mm 5x50 mm M12x100 M 12 M 12 M 12
Assembly Instructions HB-DIY1500
Sandpaper
for edges
abrading
1pc 1pc2pcs 4pcs
Allen key
Attention:
Packing 1 Packing 2 Date
Workbench is made from high quality beech wood guaranteeing maximum resistance and long service life of the
bench.
Your workbench has NO TREATMENT. Please treat your bench with a varnish or oil within 3 months of
assembly.
Don´t forget to repeat surface treatment each 6 months. This is especially important if situated in an unheated
workshop , garage or outbilding.
To increase the rigidity of your workbench ensure that you glue the joints and bolt the bench in possiton .
Wood is and natural product, check and tighten all screws and bolts every six monhts.
NOTICE: Like all solid wood products it must not be left in areas of high humidity or damp that will cause natural
movement.
Parts
Ramia s.r.o., Zátaví 58, CZ-397 01 Písek, Czech Rep blic, , Tel: [phone], fax: [phone], www.ramia.cz
All manuals and user guides at all-guides.com

PARTS and HARDWARE LIST
1
234
1 1pc 6 1pc
2 1pc 7 2pcs
3 1pc 8 2pcs
4 2pcs 9 2pcs
5 2pcs 10 2pcs
11 2pcs
ShelfBench Top
Part Name Qty
Back leg
WARNING: Wooden parts may be sharp. Before assembly, check
wooden parts and if necessary use sandpaper (part of hardware) to abrade
edges of these wooden parts.
Vice Jaw
Part
NO.: Part Name Qty Part NO.:
Front leg with dog holes
Base
Front Apron (with logo)
Back Apron
Side Apron
Middle Stretcher
Top Rail support
5
6
7
8
9
10
11
Ramia s.r.o., Zátaví 58, CZ-397 01 Písek, Czech Rep blic, , Tel: [phone], fax: [phone], www.ramia.cz
All manuals and user guides at all-guides.com

!!!! Abrade edges of these wooden parts, if neccessary !!!!
!!! HINT !!! - don´t fill up holes for dowels by glue. Smear dowels by glue and instert them into holes.
8 Top Rail s pport
9 Front leg with dog holes
10 Base
11 Back leg
!!!! Abrade edges of these wooden parts, if neccessary !!!!
Before assembly of tool shelf, decide, if you want to have deeper or shallower shelf. Grooves must be down
to get deep shelf (as shown on the picture).
7 Middle Stretcher
8 Shelf
Ramia s.r.o., Zátaví 58, CZ-397 01 Písek, Czech Rep blic, , Tel: [phone], fax: [phone], www.ramia.cz
All manuals and user guides at all-guides.com

X = holes for stretchers if cupboard is used
!!!! Abrade edges of these wooden parts - these parts must be abraded !!!!
8 Front Apron (with logo) and
holes for vice.
3 Back Apron
4 Side apron with holes for vice
Ramia s.r.o., Zátaví 58, CZ-397 01 Písek, Czech Rep blic, , Tel: [phone], fax: [phone], www.ramia.cz
All manuals and user guides at all-guides.com

A
5
Wooden vice jaw
B1
Be sure the jaws are parallel to bench top
before screwing.
!!! Hint !!! Tighten jaws using spindles.
Align jaws with bench top and then use
B3 screws for attaching jaws to spindles.
5
ABRADE EDGES
B3
Ramia s.r.o., Zátaví 58, CZ-397 01 Písek, Czech Rep blic, , Tel: [phone], fax: [phone], www.ramia.cz
All manuals and user guides at all-guides.com

Enjoy your new woodworking projects :-)
B4
Ramia s.r.o., Zátaví 58, CZ-397 01 Písek, Czech Rep blic, , Tel: [phone], fax: [phone], www.ramia.cz
All manuals and user guides at all-guides.com