R&G LP0343 User manual

Page 1of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
FITTING INSTRUCTIONS FOR LP0343 LICENCE PLATE BRACKET
This kit contains the items pictured and labelled over page.
Some parts may be shown for clarity of instructions only.
Do not proceed until you are sure all parts are present.
Please read all instructions before proceeding.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY AQUALIFIED TECHNICIAN.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike.
In the event of rubber washers being used to hold components onto bolts,
these rubber washers can be thrown away.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM
WWW.RG-RACING.COM

Page 2of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
LEGEND
TOOLS REQUIRED
•Set of metric Hex keys to include
3mm, 4mm and 5mm.
•T30 Torx head tool
•Set of metric sockets and wrench.
To include 6, 8 & 10mm.
•8mm & 10mm spanners.
•Phillips screwdriver.
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm
ITEM No.
DESCRIPTION
QTY
ITEM 1
TB0343 PART 1 LICENCE PLATE BRACKET
1
ITEM 2
TB0343 PART 2 LICENCE PLATE SUPPORT
1
ITEM 3
TB0299 PART 2 LICENCE PLATE MOUNT
1
ITEM 4
S0722 TAIL BRACKET MOUNTING SPACER
2
ITEM 5
S0294 SPACER
1
ITEM 6
M6 x 1.00 x 20mm BUTTON HEAD BOLT
2
ITEM 7
M6 x 1.00 x 25mm BUTTON HEAD BOLT
1
ITEM 8
M5 x 0.8 x 15mm COUNTERSUNK BOLT
8
ITEM 9
M6 x 12mm OD WASHER
3
ITEM 10
M6 x 19mm OD WASHER
2
ITEM 11
M5 x 10mm OD WASHER
8
ITEM 12
M6 NYLOC NUT
2
ITEM 13
M5 NYLOC NUT
8
ITEM 14
RB0002 RUBBER BUNG
1
ITEM 15
LA0002 NUMBER PLATE LIGHT
1
ITEM 16
666-896 150mm HEAT SHRINK
1
ITEM 17
CT100BK 2.5 x 100mm CABLE TIE
8
ITEM 18
CLIP 1 SELF ADHESIVE CABLE CLIP
4
ITEM 19
REFL 3 REFLECTOR
1
ITEM 20
CON0014 LICENCE PLATE ILLUMINATOR CONNECTOR
1

Page 3of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
ASSEMBLY DIAGRAM 1

Page 4of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
ASSEMBLY DIAGRAM 2

Page 5of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
DIAGRAM 3

Page 6of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
FITTING PICTURES
PICTURE 1
PICTURE 2
PICTURE 3

Page 7of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
FITTING INSTRUCTIONS
Before fitting the R&G tail tidy you will need to remove some OEM parts. Below is a suggested
list of parts to be removed.
•Rear seat
•Rear side panels
•Under rear seat cover plate
•OEM number plate bracket
•Seat lock mechanism
•OEM indicators
•Unplug indicator and number plate light wires
Tail Tidy Assembly
Before assembling this product, ensure all the components within the box are correct by
comparing the legend and diagrams.
1. To start assembling the tail tidy, connect (ITEM 1) and (ITEM 2) together using x4 (ITEM 8)
(ITEM 11) (ITEM 13) as shown in DIAGRAM 1-2. DO NOT FULLY TIGHTEN AT THIS STAGE.
2. Connect (ITEM 3) to the now constructed assembly (ITEM 1/2) using x4 (ITEM 8) (ITEM
11) (ITEM 13) as shown in DIAGRAM 1-2.
3. Once (ITEM 3) is connect, you can attach (ITEM 15) into the mounting holes on (ITEM 3) as
shown in DIAGRAM 2. MAKE SURE WIRES ARE PLACED THROUGH (ITEM 3). Once tightened,
slide the HEAT SHRINK (ITEM 16) over the wires of(ITEM 15).
4. As shown in DIAGRAM 1 push (ITEM 14) into the hole of (ITEM 1).
5. To help cable tidy the wires, you will need to use the SELF-ADHESIVE CABLE CLIP (ITEM 18)
to pin the wires to the inside of (ITEM 1) on either side.
6. Push the cables through the hole in (ITEM 14).
7. To install the TAIL BRACKET MOUNTING SPACERS (ITEM 4), you will need to directly
replace the OEM SPACERS as shown in PICTURE 1.
8. Now the Tail Tidy is assembled, it is time to attach it to the motorbike. To do so place the
assembly in the same mounting location as the OEM number plate bracket using x2
(ITEM 6) (ITEM 9) (ITEM 12).

Page 8of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
MAKE SURE TO DO-
Make sure the washer (ITEM 9) is placed onto the bolt (ITEM 6) before being mounted. Also
slot the wires through the small hole in the rear undertray as shown in PICTURE 2.
Once the tail tidy is mounted to the bike, ensure it is tight and secure.
9. After mounting the tail tidy, the centre bolt (ITEM 7) with washer (ITEM 9) will need to be
bolted through the mounting hole in the LICENCE PLATE SUPPORT (ITEM 2) as shown in
DIAGRAM 1-2.
Make sure that the SPACER (ITEM 5) is placed in between the bike mounting location and
(ITEM 2).
10. Plug in the Number plate light (ITEM 15) wires into the Licence plate illuminator connector
(ITEM 20) as shown in PICTURE 3. Once connected, plug (ITEM 20) into the motorbikes OEM
number plate light connector.
11. Now fully tighten (ITEM 1) and (ITEM 2).
12. Ensure that all the nuts and bolts have been tighten properly using the GENERAL TORQUE
SETTINGS table on PAGE 2.
13. Turn the motorbike on to test the Number Plate Light (ITEM 15)is working.
14. To install the OEM indicators, remove these from the OEM tail unit by removing the securing nut
from each indicator and thread the wire through the bracket to remove.
Ensuring to fix the indicators to the correct side, thread the connector and wire through the
indicator mount on the licence plate bracket and the wire hole on (ITEM 1). Then tighten the
indicators securely with the with the OEM indicator nut.
15. Final step, re-install all OEM parts except from the OEM Number Plate Bracket.
IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT LOW DOWN ON THE
LICENCE PLATE MOUNT, THERE IS A POTENTIAL CHANCE THE LICENCE PLATE COULD HIT
THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD. IT IS YOUR
RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING ACTION. FAILURE
TO CHECK THIS COULD RESULT IN SERIOUS INJURY.
ISSUE 1 27/09/2022 (JH)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer’s statutory rights.

Page 9of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does
not refer to faulty goods.

Page 10 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
NOTICE DE MONTAGE LP0343 SUPPORT DE PLAQUE
C
E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE
.
CERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS.
NE PAS PROCEDER AU MONTAGE TANT QUE VOUS N'ETES PAS SUR QUE TOUTES LES PIECES SOIENT
PRESENTES.
VEUILLEZ LIRE TOUTES LES INSTRUCTIONS AVANT DE CONTINUER.
EN CAS DE DOUTE LORS DU MONTAGE DE NOS PRODUITS, CONSULTEZ UN DE NOS
REVENDEURS OU FAITES APPEL A UN TECHNICIEN QUALIFIÉ.
VEUILLEZ NOTER QUE LA FAÇON DONT LE KIT EST EMBALLE NE REPRESENTE PAS NECESSAIREMENT LA
MANIERE DE LE MONTER SUR LA MOTO.
SI DES RONDELLES EN CAOUTCHOUC SONT UTILISEES POUR MAINTENIR LES COMPOSANTS SUR LES
BOULONS,ELLES PEUVENT ETRE JETEES.
NOTICE DISPONIBLE AU TELECHARGEMENT SUR :
WWW.RG-RACING.COM

Page 11 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
LÉGENDE
OUTILS REQUIS
•Clés hexagonales 3mm, 4mm et
5mm.
•Clé Torx T30
•Clé à cliquet + douilles 6, 8 &
10mm.
•Clé à molette 8mm & 10mm.
•Tournevis cruciforme.
VALEURS DE SERRAGE
M4 BOULON = 8Nm
M5 BOULON = 12Nm
M6 BOULON = 15Nm
M8 BOULON = 20Nm
M10 BOULON = 40Nm
M12 BOULON = 40Nm
ARTICLE No.
DESCRIPTION
QTÉ
ARTICLE 1
TB0343 PARTIE 1SUPPORT DE PLAQUE
1
ARTICLE 2
TB0343 PARTIE 2 SUPPORT DE PLAQUE
1
ARTICLE 3
TB0299 PARTIE 2 SUPPORT DE PLAQUE
1
ARTICLE 4
S0722 ENTRETOISE DE SUPPORT DE PLAQUE
2
ARTICLE 5
S0294 ENTRETOISE
1
ARTICLE 6
M6 x 1.00 x 20mm BOULON
2
ARTICLE 7
M6 x 1.00 x 25mm BOULON
1
ARTICLE 8
M5 x 0.8 x 15mm BOULON
8
ARTICLE 9
M6 x 12mm RONDELLE
3
ARTICLE 10
M6 x 19mm RONDELLE
2
ARTICLE 11
M5 x 10mm RONDELLE
8
ARTICLE 12
M6 ÉCROU
2
ARTICLE 13
M5 ÉCROU
8
ARTICLE 14
RB0002 BOUCHON EN CAOUTCHOUC
1
ARTICLE 15
LA0002 FEU DE PLAQUE
1
ARTICLE 16
666-896 150mm MANCHON THERMO RÉTRACTABLE
1
ARTICLE 17
CT100BK 2.5 x 100mm COLLIER DE SERRAGE
8
ARTICLE 18
CLIP 1 CLIP CÂBLE AUTOCOLLANT
4
ARTICLE 19
REFL 3 RÉFLECTEUR
1
ARTICLE 20
CON0014 CONNECTEUR DE FEU DE PLAQUE
1

Page 12 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
SCHÉMA D’ENSEMBLE 1

Page 13 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
SCHÉMA D’ENSEMBLE 2

Page 14 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
SCHÉMA 3

Page 15 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
PHOTOS DE MONTAGE
PHOTO 1
PHOTO 2
PHOTO 3

Page 16 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
NOTICE DE MONTAGE
Avant de monter le support arrière R&G, vous devrez retirer certaines pièces d’origine. Vous
trouverez ci-dessous une liste suggérée de pièces à retirer.
•Siège arrière
•Panneaux latéraux arrière
•Sous la plaque de couverture du siège arrière
•Support de plaque d'immatriculation d’origine
•Mécanisme de verrouillage du siège
•Clignotants d’origine
•Débranchez les fils des clignotants et des feux de plaque d'immatriculation
Assemblage du support
Avant d'assembler ce produit, assurez-vous que tous les composants de la boîte soient corrects
en comparant la légende et les schémas.
16.Pour commencer à assembler le support arrière, connectez (ARTICLE 1) et (ARTICLE 2) à l'aide
de x4 (ARTICLE 8)
ARTICLE 11) (ARTICLE 13) comme indiqué dans le SCHÉMA 1-2. NE PAS SERRER
COMPLÈTEMENT À CE STADE.
Connectez (ARTICLE 3) à l'ensemble qui a présent est assemblé (ARTICLE 1/2) en utilisant x4
(ARTICLE 8) (ARTICLE 11) (ARTICLE 13) comme indiqué sur le SCHÉMA 1-2.
17. Une fois que (ARTICLE 3) est connecté, vous pouvez fixer (ARTICLE 15) dans les trous de
montage sur (ARTICLE 3) comme indiqué sur le SCHÉMA 2. ASSUREZ-VOUS QUE LES FILS
SOIENT PASSÉS À TRAVERS (ARTICLE 3). Une fois serré, glissez la THERMORÉTRACTABLE
(ARTICLE 16) sur les fils de (ARTICLE 15).
18. Comme indiqué sur le SCHÉMA 1, poussez (ARTICLE 14) dans le trou de (ARTICLE 1).
19. Pour faciliter le rangement des câbles, vous devrez utiliser le CLIP DE CÂBLE AUTO-ADHÉSIF
(ARTICLE 18) pour fixer les câbles à l'intérieur de (ARTICLE 1) de chaque côté.
20. Pousser les câbles à travers le trou (ARTICLE 14).
21. Pour installer les ENTRETOISES DE MONTAGE DU SUPPORT (ARTICLE 4), vous devrez remplacer
directement les ENTRETOISES d’origine comme indiqué sur la PHOTO 1.
22. Maintenant que le support est assemblé, il est temps de le fixer à la moto. Pour ce faire, placez
l'ensemble dans le même emplacement de montage que le support de plaque d'immatriculation
d’origine en utilisant x2
(ARTICLE 6) (ARTICLE 9) (ARTICLE 12).

Page 17 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
ASSUREZ-VOUS DE FAIRE-
Assurez-vous que la rondelle (ARTICLE 9) soit placée sur le boulon (ARTICLE 6) avant de le
monter. Faites également passer les fils à travers le petit trou du passage de roue arrière
comme indiqué sur la PHOTO 2.
Une fois le support monté sur la moto, assurez-vous qu'il soit bien serré et sécurisé.
1. Après avoir monté le support arrière, le boulon central (ARTICLE 7) avec rondelle (ARTICLE 9)
devra être boulonné à travers le trou de montage du SUPPORT DE PLAQUE
D'IMMATRICULATION (ARTICLE 2) comme indiqué sur le SCHÉMA 1-2.
Assurez-vous que l'ENTRETOISE (ARTICLE 5) soit placée entre l'emplacement de montage de la
moto et (ARTICLE 2).
2. Branchez les fils de feu de la plaque d'immatriculation (ARTICLE 15) dans le connecteur de feu
de la plaque d'immatriculation (ARTICLE 20) comme indiqué sur la PHOTO 3. Une fois connecté,
branchez (ARTICLE 20) dans le connecteur de l'éclairage de la plaque d'immatriculation
d’origine de la moto.
3. Serrez maintenant à fond (ARTICLE 1) et (ARTICLE 2).
4. Assurez-vous que tous les écrous et boulons aient été correctement serrés en utilisant le
tableau des RÉGLAGES GÉNÉRAUX DE COUPLE à la PAGE 2.
5. Allumez la moto pour vérifier que le feu de la plaque d'immatriculation (ARTICLE 15)
fonctionne.
6. Pour installer les clignotants d’origine, retirez-les de l'unité arrière d’origine en retirant l'écrou
de fixation de chaque clignotant et enfilez le fil à travers le support pour le retirer.
En vous assurant de fixer les clignotants du bon côté, enfilez le connecteur et le fil à travers le
support de clignotant sur le support de plaque d'immatriculation et le trou de fil (ARTICLE 1).
Ensuite, serrez fermement les clignotants avec l'écrou de clignotant d’origine.
7. Dernière étape, réinstallez toutes les pièces d’origine à l'exception du support de plaque
d'immatriculation d’origine.
IMPORTANT : SI VOUS MONTEZ UNE PLAQUE D'IMMATRICULATION LARGE ET QUE VOUS LA
PLACEZ ASSEZ BASSE SUR LE SUPPORT DE PLAQUE D'IMMATRICULATION, IL EST POSSIBLE
QUE LA PLAQUE D'IMMATRICULATION TOUCHE LA ROUE ARRIÈRE SOUS UNE CHARGE
LOURDE ET SUR DE GROSSES BOSSES SUR LA ROUTE. IL EST DE VOTRE RESPONSABILITÉ DE
VÉRIFIER CETTE POSSIBILITÉ ET DE PRENDRE DES MESURES POUR ÉVITER. NE PAS
VÉRIFIER CELA POURRAIT ENTRAÎNER DES BLESSURES GRAVES.
ISSUE 1 27/09/2022 (JH)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products

Page 18 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does
not refer to faulty goods.

Page 19 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
MONTAGEANLEITUNG FÜR LP0343 KENNZEICHENHALTER
Alle Kit-Teile sind auf den nachfolgenden Seiten abgebildet und gekennzeichnet.
Die abgebildeten Teile dienen lediglich zur Erklärung.
Überprüfen Sie zuerst, dass alle Teile vorhanden sind.
Lesen Sie die Montageanleitung komplett durch, bevor Sie anfangen.
WENN SIE BEI DER MONTAGE DIESES PRODUKTES UNSICHER SIND, BITTE EINEN
UNSERER HÄNDLER KONTAKTIEREN ODER DAS KIT VON EINEM QUALIFIZIERTEN
ZWEIRAD-MECHANIKER MONTIEREN LASSEN.
Die Verpackung der Teile stellt nicht die Reihenfolge der Montage dar.
Hinweis für Kits mit Plastikunterlegscheiben an den Schrauben –
Diese Plastik-Unterlegscheiben werden nicht für den Einbau benötigt!
EINE DIGITALE VERSION DIESER MONTAGEANLEITUNG KANN AUF
FOLGENDER SEITE HERUNTERGELADEN WERDEN:
WWW.RG-RACING.COM

Page 20 of 26 LP0343
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone]www.rg-racing.com Email: [e-mail]
LIEFERUMFANG
SIE BENÖTIGEN FOLGENDES WERKZEUG:
•Satz Inbusschlüssel inkl. 3mm,
4mm and 5mm.
•T30 Torx-Schlüssel
•Satz Steckschlüssel inkl. 6, 8 &
10mm.
•8mm & 10mm Schraubenschlüssel
•Kreuzschlitz-Schraubenzieher
ALLGEM. ANZUGSDREHMOMENT
M4 SCHRAUBE = 8Nm
M5 SCHRAUBE = 12Nm
M6 SCHRAUBE = 15Nm
M8 SCHRAUBE = 20Nm
M10 SCHRAUBE = 40Nm
M12 SCHRAUBE = 40Nm
ARTIKEL NR.
BESCHREIBUNG
MENGE
ARTIKEL 1
TB0343 TEIL 1 KENNZEICHENHALTER - HALTERUNG
1
ARTIKEL 2
TB0343 TEIL 2 KENNZEICHENHALTER - STÜTZE
1
ARTIKEL 3
TB0299 TEIL 2 KENNZEICHENHALTER
1
ARTIKEL 4
S0722 DISTANZHALTER MONTAGE KENNZEICHENHALTER
2
ARTIKEL 5
S0294 DISTANZHALTER
1
ARTIKEL 6
M6 x 1.00 x 20mm INBUSSCHRAUBE
2
ARTIKEL 7
M6 x 1.00 x 25mm INBUSSCHRAUBE
1
ARTIKEL 8
M5 x 0.8 x 15mm SENKSCHRAUBE
8
ARTIKEL 9
M6 x 12mm OD UNTERLEGSCHEIBE
3
ARTIKEL 10
M6 x 19mm OD UNTERLEGSCHEIBE
2
ARTIKEL 11
M5 x 10mm OD UNTERLEGSCHEIBE
8
ARTIKEL 12
M6 SELBSTSICHERNDE MUTTER
2
ARTIKEL 13
M5 SELBSTSICHERNDE MUTTER
8
ARTIKEL 14
RB0002 GUMMITÜLLE
1
ARTIKEL 15
LA0002 KENNZEICHENBELEUCHTUNG
1
ARTIKEL 16
666-896 150mm SCHRUMPFSCHLAUCH
1
ARTIKEL 17
CT100BK 2.5 x 100mm KABELBINDER
8
ARTIKEL 18
CLIP 1 SELBSTKLEBENDER KABELCLIP
4
ARTIKEL 19
REFL 3 RÜCKSTRAHLER
1
ARTIKEL 20
CON0014 VERBINDER KENNZEICHENBELEUCHTUNG
1