R&G PKS0115 User manual

PKS0115
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
Page | 1
FITTING INSTRUCTIONS FOR PKS0115 KICKSTAND SHOE
KTM DUKE 790 ‘18-
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike.
THE PARTS SHOWN MAY BE REPRESENTATIVE ONLY (FOR CLARITY OF INSTRUCTIONS ONLY).
LEGEND
ITEM 1 = CLAMP PLATE (PLATE 0224) (x1)
ITEM 2 = BASE PLATE (MP0216) (x1)
ITEM 3 = M5 x 8mm LONG COUNTERSUNK HEAD BOLTS (x4)

PKS0115
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
Page | 2
TOOLS REQUIRED
•3mm A/F Allen Key.
•Thread Lock (Blue).
FITTING INSTRUCTIONS
•Take the clamp plate and feed it over the base of the side stand, with the countersunk holes facing upwards and
position it around the side stand leg.
•Offer the base plate up to the underside of the side stand base.
•Apply a small amount (one drop) of Thread Lock (Blue) to the end of the threaded area of each screw.
•Fit the four M5 bolts clamping the two plates together and securely mount onto the side stand foot.
•Tighten all bolts evenly and check to ensure the side stand pad clears the chain when in the raised position.
•If fitting to older stands that have been worn the padding strip should be placed in the base plate to ensure a
tighter fit. ISSUE 11/07/2018 (HB)
Digital copies of these instructions are available to download from www.rg-racing.com
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer’s statutory rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of
R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P –at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.

PKS0115
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
Page | 3
NOTICE DE MONTAGE POUR PKS0115 PIED DE BEQUILLE
KTM DUKE 790 ‘18-
Le kit contient les articles exposés ci-dessous, vérifier que toutes les pièces soient présentes avant de procéder au
montage.
LA FAÇON DONT LE KIT EST EMBALLE NE CORRESPOND PAS FORCEMENT A LA FAÇON DE MONTER LES
PIECES SUR LA MOTO.
LES PARTIES PRESENTÉES PEUVENT ETRE UNIQUEMENT REPRESENTATIVES (POUR LA CLARTE DES
INSTRUCTIONS UNIQUEMENT).
LÉGENDE
ARTICLE 1 = PLAQUE D’ATTACHE (PLATE 0224) (x1)

PKS0115
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
Page | 4
ARTICLE 2 = BASE PLATE (MP0216) (x1)
ARTICLE 3 = M5 x 8mm BOULONS (x4)
OUTILS REQUIS
•Clé Allen 3mm.
•Verrouillage du filetage (Bleu).
NOTICE DE MONTAGE
•Prenez l’attache puis placez-là autour avec les trous orientés vers le haut et positionnez-la autour de la béquille
latérale.
•Monter la base plate au-dessous de la base de béquille latérale.
•Appliquer un peu de colle (un filet) de verrouillage du filetage (Bleu) sur l’extrémité du filetage de chaque vis.
•Insérer les 4 boulons M5 pour emboiter les 2 plaques ensemble puis fixer sur le pied de béquille latérale.
•Serrer tous les boulons de façon identique puis vérifier que le coussin de béquille latérale ne touche pas la chaine
en position relevée.
•Si l’installation s’effectue sur une béquille usée, la bande de rembourrage doit être placée sur la base plate pour
assurer une installation plus précise. ISSUE 11/07/2018 (HB)
Notice disponible au téléchargement sur www.rg-racing.com
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer’s statutory rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of
R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P –at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.

PKS0115
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
Page | 5
MONTAGEANLEITUNG FÜR PKS0115 SEITENSTÄNDER-
AUFLAGENVERBREITERUNG KTM DUKE 790 ‘18-
ALLE KIT-TEILE SIND UNTEN ABGEBILDET UND GEKENNZEICHNET. BEVOR SIE MIT DER
MONTAGE BEGINNEN, ÜBERPRÜFEN SIE, DASS ALLE TEILE VORHANDEN SIND.
Hinweis: Die Verpackung der Teile stellt nicht die Reihenfolge der Montage dar.
DIE UNTEN ABGEBILDETEN TEILE DIENEN LEDIGLICH ZUR ERKLÄRUNG
LIEFERUMFANG
ARTIKEL 1 = KLEMMPLATTE (PLATE 0224) (x1)
ARTIKEL 2 = GRUNDPLATTE (MP0216) (x1)
ARTIKEL 3 = M5 x 8mm SENKSCHRAUBEN (x4)

PKS0115
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
Page | 6
SIE BENÖTIGEN FOLGENDES WERKZEUG
•3mm A/F Inbusschlüssel
•Schraubensicherung Thread Lock (Blue)
MONTAGEANLEITUNG
•Montieren Sie die Klemmplatte über dem Fuß des Seitenständers. Die Versenkungen nach oben.
•Nehmen Sie die Grundplatte und montieren Sie sie an der Unterseite des Seitenständerfuß.
•Eine kleine Menge (einen Tropfen) Schraubensicherung (blau) am Ende des Schraubengewindes aller Schrauben
anbringen.
•Die vier M5 Schrauben, die die zwei Platten in Position zusammenklemmen, jetzt montieren und am
Seitenständer fixieren.
•Ziehen Sie alle Schrauben fest und überprüfen Sie, dass die Kette nicht von der Auflagen-Verbreiterung berührt
wird, wenn der Seitenständer eingeklappt ist.
•Bei der Montage an älteren Seitenständern, die etwas abgenutzt sind, den Schaumstoffstreifen in der
Grundplatte anbringen, um die Passform zu verbessern.
AUSGABE 11/07/2018 (HB)
Eine digitale Version dieser Montageanleitung kann auf folgender Seite heruntergeladen werden:
www.rg-racing.com
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and
supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in
R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the
Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be
limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary).
Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P
–at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.