R&G PKS0119 User manual

Page 1of 6 PKS0119
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone]www.rg-racing.com Email: [e-mail]
FITTING INSTRUCTIONS FOR PKS0119 KICKSTAND SHOE
HUSQVARNA VITPILEN 701 2018 –
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto the bolt – the rubber washers
should be thrown away !
THE PARTS SHOWN MAY BE REPRESENTATIVE ONLY (FOR CLARITY OF INSTRUCTIONS ONLY)
Digital copies of these instructions are available to download from www.rg-racing.com
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
TOOLS REQUIRED
•3mm A/F Allen Key.
•Thread Lock (Blue 242)

Page 2of 6 PKS0119
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone]www.rg-racing.com Email: [e-mail]
This Kit Contains:
Item 1= 1x Base Plate (MP0223)
Item 2 = 1x Clamp Plate (PLATE 0229)
Item 3 = 3x M5 x 8mm Countersunk Head Bolts
FITTING INSTRUCTIONS
•Take the clamp plate (Item 2) and feed it over the base of the side stand, with the countersunk holes facing
upwards and position it around the side stand leg.
•Offer the base plate (Item 1) up to the underside of the side stand base.
•Apply a small amount (one drop) of Thread Lock (Blue 242) to the end of the threaded area of each bolt.
•Fit the three M5 bolts clamping the two plates together and securely mount onto the side stand foot.
•Tighten all bolts evenly and check to ensure the side stand pad clears the chain when in the raised position.
•If fitting to older stands that have been worn the padding strip should be placed in the base plate to ensure a
tighter fit.
ISSUE 1 15/11/2018 (FB)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do
not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no
representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and
the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the
Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has
been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of
any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal
injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the
Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the
opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P –at the prevailing price at
time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase.
This policy does not affect your statutory rights and does not refer to faulty goods.

Page 3of 6 PKS0119
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone]www.rg-racing.com Email: [e-mail]
NOTICE DE MONTAGE POUR PKS0119 PIED DE BEQUILLE
HUSQVARNA VITPILEN 701 2018 –
Le kit contient les articles exposés ci-dessous, vérifier que toutes les pièces soient présentes avant de procéder au montage.
La façon dont le kit est emballé ne correspond pas forcément à la façon de monter les pièces sur la moto
Notez que si les kits sont emballés avec des rondelles en caoutchouc servant à tenir les composants, ces rondelles doivent être
jetées !
LES PARTIES PRESENTÉES PEUVENT ETRE UNIQUEMENT REPRESENTATIVES (POUR LA CLARTE DES
INSTRUCTIONS UNIQUEMENT).
Notice disponible au téléchargement sur www.rg-racing.com
VALEURS DE SERRAGE RECOMMANDEES
M4 BOULON =8NM
M5 BOULON =12NM
M6 BOULON =15NM
M8 BOULON =20NM
M10 BOULON =40NM
OUTILS REQUIS
•Clé Allen 3mm.
•Frein filet (Bleu 242)

Page 4of 6 PKS0119
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone]www.rg-racing.com Email: [e-mail]
Le kit contient :
Article 1= 1x Base Plate (MP0223)
Article 2 = 1x Attache plate (PLATE 0229)
Article 3 = 3x M5 x 8mm Boulons
NOTICE DE MONTAGE
•Prenez l’attache (Article 2) puis placez-la autour de la base de la béquille latérale, les fraisures étant tournées vers le
haut puis positionnez-la autour du pied de béquille latérale.
•Monter la base plate (Article 1) au-dessous de la base de béquille latérale.
•Appliquer un peu de colle (un filet) de frein filet (Loctite Bleu 242) sur l’extrémité du filetage du boulon.
•Insérer les 3 boulons M5 pour emboiter les 2 plaques ensemble puis fixer sur le pied de béquille latérale.
•Serrer tous les boulons de façon identique puis vérifier que le coussin de béquille latérale ne touche pas la chaine en
position relevée.
•Si l’installation s’effectue sur une béquille usée, la bande de rembourrage doit être placée sur la base plate
pour assurer une installation plus précise.
ISSUE 1 15/11/2018 (FB)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do
not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no
representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and
the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the
Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has
been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of
any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal
injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the
Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the
opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P –at the prevailing price at
time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase.
This policy does not affect your statutory rights and does not refer to faulty goods.

Page 5of 6 PKS0119
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone]www.rg-racing.com Email: [e-mail]
MONTAGEANLEITUNG FÜR PKS0119 SEITENSTÄNDER-AUFLAGENVERBREITERUNG
HUSQVARNA VITPILEN 701 2018 –
ALLE KIT-TEILE SIND UNTEN ABGEBILDET UND GEKENNZEICHNET. BEVOR SIE MIT DER MONTAGE
BEGINNEN, ÜBERPRÜFEN SIE, DASS ALLE TEILE VORHANDEN SIND.
Hinweis: Die Verpackung der Teile stellt nicht die Reihenfolge der Montage dar.
Hinweis für Kits mit Plastikunterlegscheiben an den Schrauben –Diese Plastikunterlegscheiben werden nicht für den Einbau
benötigt!
DIE UNTEN ABGEBILDETEN TEILE DIENEN LEDIGLICH ZUR ERKLÄRUNG
Eine digitale Version dieser Montageanleitung kann auf folgender Seite heruntergeladen werden:
www.rg-racing.com
ALLGEM.ANZUGSDREHMOMENT
M4 SCHRAUBE = 8Nm
M5 SCHRAUBE = 12Nm
M6 SCHRAUBE = 15Nm
M8 SCHRAUBE = 20Nm
M10 SCHRAUBE = 40Nm
SIE BENÖTIGEN FOLGENDES WERKZEUG
•3mm A/F Inbusschlüssel
•Schraubensicherung Thread Lock (Blue 242)

Page 6of 6 PKS0119
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone]www.rg-racing.com Email: [e-mail]
Inhalt des Kits:
Artikel 1= 1x Grundplatte (MP0223)
Artikel 2 = 1x Klemmplatte (PLATE 0229)
Artikel 3 = 3x M5 x 8mm Senkschrauben
MONTAGEANLEITUNG
•Montieren Sie die Klemmplatte (Artikel 2) über dem Fuß des Seitenständers. Die Versenkungen nach oben.
•Nehmen Sie die Grundplatte(Artikel 1) und montieren Sie sie an der Unterseite des Seitenständerfuß.
•Eine kleine Menge (einen Tropfen) Schraubensicherung (blau 242) am Ende des Schraubengewindes der Schrauben
anbringen.
•Die drei M5 Schrauben, die die zwei Platten in Position zusammenklemmen, jetzt anbringen und am Seitenständer
fixieren.
•Ziehen Sie alle Schrauben fest und überprüfen Sie, dass die Kette nicht von der Auflagen-Verbreiterung berührt wird,
wenn der Seitenständer eingeklappt ist.
•Bei der Montage an älteren Seitenständern, die etwas abgenutzt sind, den Schaumstoffstreifen in der
Grundplatte anbringen, um die Passform zu verbessern.
AUSGABE 1 15/11/2018 (FB)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal
and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than
those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or
undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the
warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but
shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect
arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss
and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary).
Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P –at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy
does not affect your statutory rights and does not refer to faulty goods.