R&G PKS0110SI User manual

R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
- 1 -
Page | 1
FITTING INSTRUCTIONS FOR PKS0110SI KICKSTAND SHOE
BMW G310 GS ‘17-
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike.
THE PARTS SHOWN MAY BE REPRESENTATIVE ONLY (FOR CLARITY OF INSTRUCTIONS ONLY)
Please note that in cases where kits are packed with rubber washers holding the components onto the
bolt –the rubber washers should be thrown away!
BASE PLATE (MP0201)
CLAMP PLATE (PLATE 0215)
3x M5 x 6mm LONG
COUNTERSUNK BOLTS

R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
- 2 -
Page | 2
TOOLS REQUIRED
3mm A/F Allen key.
Thread Lock (Blue).
FITTING INSTRUCTIONS
Take the clamp plate and feed it over the base of the side stand, with the countersunk holes
facing upwards and position it around the side stand leg.
Offer the base plate up to the underside of the side stand base.
Apply a small amount (one drop) of Thread Lock (Blue) to the end of the threaded area of
each screw.
Fit the three M5 bolts clamping the two plates together and securely mount onto the side stand
foot.
Tighten all bolts evenly and check to ensure the side stand pad clears the chain when in the
raised position.
If fitting to older stands that have been worn the padding strip should be placed in the base
plate to ensure a tighter fit.
ISSUE 1 23/10/2017 (AR)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do
not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no
representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and
the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the
Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been
disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any
defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal
injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the
Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the
opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P –at the prevailing price at time of
purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy
does not affect your statutory rights and does not refer to faulty goods.

R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
- 3 -
Page | 3
NOTICE DE MONTAGE POUR PKS0110SI PIED DE BEQUILLE
BMW G310 GS ‘17-
LA FAÇON DONT LE KIT EST EMBALLE NE CORRESPOND PAS FORCEMENT A LA FAÇON DE
MONTER LES PIECES SUR LA MOTO.
LES PARTIES PRESENTEES PEUVENT ETRE UNIQUEMENT
REPRESENTATIVES (POUR LA CLARTE DES INSTRUCTIONS UNIQUEMENT).
Notez que si les kits sont emballés avec des rondelles en caoutchouc servant à tenir les composants, ces
rondelles doivent être jetées !
BASE PLATE (MP0201)
ATTACHE (PLATE 0215)
3x M5 x 6mm BOULONS

R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
- 4 -
Page | 4
OUTILS REQUIS
Clé Allen 3mm.
Blocage fileté (Bleu).
NOTICE DE MONTAGE
Prenez l’attache puis placez-la autour de la base de la béquille latérale, avec les trous orientés
vers le haut puis positionner la autour de la base de la béquille.
Monter la base plate au-dessous de la base de béquille latérale.
Appliquer un peu de superglue (un filet) dans le blocage de filetage (Bleu) sur l’extrémité du
filetage de chaque vis.
Insérer les 3 boulons M5 pour emboiter les 2 plaques ensemble puis fixer sur le pied de
béquille latérale.
Serrer tous les boulons de façon identique puis vérifier que le coussin de béquille latérale ne
touche pas la chaine en position relevée.
Si l’installation s’effectue sur une béquille usée, la bande de rembourrage doit être placée sur
la base plate pour assurer une installation plus précise.
ISSUE 1 23/10/2017 (AR)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do
not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no
representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and
the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the
Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been
disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any
defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal
injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the
Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the
opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P –at the prevailing price at time of
purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy
does not affect your statutory rights and does not refer to faulty goods.

R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
- 5 -
Page | 5
MONTAGEANLEITUNG FÜR PKS0110SI
SEITENSTÄNDER-AUFLAGENVERBREITERUNG
BMW G310 GS ‘17-
Hinweis: Die Verpackung der Teile stellt nicht die Reihenfolge der Montage dar.
DIE UNTEN ABGEBILDETEN TEILE DIENEN LEDIGLICH ZUR ERKLÄRUNG
Hinweis für Kits mit Plastikunterlegscheiben an den Schrauben –Diese Plastikunterlegscheiben
werden nicht für den Einbau benötigt!
GRUNDPLATTE (MP0201)
KLEMMPLATTE
(PLATE 0215)
3x M5 x 6mm
SENKSCHRAUBEN

R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: [phone] Fax: [phone] www.rg-racing.com Email: [e-mail]
- 6 -
Page | 6
SIE BENÖTIGEN FOLGENDES WERKZEUG
3mm A/F Inbusschlüssel
Schraubensicherung z.B. Thread Lock (Blue)
MONTAGEANLEITUNG
Montieren Sie die Klemmplatte über dem Fuß des Seitenständers. Die Versenkungen nach
oben.
Nehmen Sie die Grundplatte und montieren Sie sie an der Unterseite des Seitenständerfuß.
Eine kleine Menge (einen Tropfen) Schraubensicherung (blau) am Ende des
Schraubengewindes der drei Schrauben anbringen.
Die drei M5 Schrauben, die die zwei Platten in Position zusammenklemmen, nun anbringen
und am Seitenständer fixieren.
Ziehen Sie alle Schrauben fest und überprüfen Sie, dass die Kette nicht von der Auflagen-
Verbreiterung berührt wird, wenn der Seitenständer eingeklappt ist.
Bei der Montage an älteren Seitenständern, die etwas abgenutzt sind, den Polstersteifen in der
Grundplatte anbringen, um die Passform zu verbessern.
AUSGABE 1 23/10/2017 (AR)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their
performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has
been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable
quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free
of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the
Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from
accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer’s statutory rights. R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer
must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G. All returns are subject to a 25%
restocking and handling fee (25% of the gross value exc. P&P –at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns
of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.