Raven SmartBoom RoGator 864 User manual

SmartBoom™ Installation Manual
RoGator 864, 874, 1064, 1074 (2006 & Newer)

While every effort has been made to ensure the accuracy of this document,
Raven Industries assumes no responsibility for omissions and errors. Nor is any
liability assumed for damages resulting from the use of information contained
herein.
Raven Industries shall not be responsible or liable for incidental or consequential
damages or a loss of anticipated benefits or profits, work stoppage or loss, or
impairment of data arising out of the use, or inability to use, this system or any of
its components. Raven Industries shall not be held responsible for any
modifications or repairs made outside our facilities, nor damages resulting from
inadequate maintenance of this system.
As with all wireless and satellite signals, several factors may affect the availability
and accuracy of wireless and satellite navigation and correction services (e.g.
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the
accuracy, integrity, continuity, or availability of these services and cannot
guarantee the ability to use Raven systems, or products used as components of
systems, which rely upon the reception of these signals or availability of these
services. Raven Industries accepts no responsibility for the use of any of these
signals or services for other than the stated purpose.
Disclaimer
©Raven Industries, Inc. 2009, 2012

Manual # 016-1001-057
1
Important! All boom switches must be in the OFF
position and master switch must be in the ON position
while Smartboom is in operation!
C H A P T E R
1
INTRODUCTION
Congratulations on your purchase of the Raven Smartboom system! This system
is designed to provide worry-free turn on and turn off of your booms with respect to
an as-applied area. The following instructions are designed to assist you in the
proper installation of the Smartboom system. See the Operation Manual of your
Smartboom console for instructions on setting up the software and using the
Smartboom system.

Rogator 864, 1064, 874, 1074 (Jan. 2006 & Newer) SmartBoom Installation Manual
2
Notes:

Manual # 016-1001-057
3
C H A P T E R
2
INSTALLATION
Use the following procedure to properly install the Smartboom system.
1. Locate the 12 pin armrest harness connector behind the armrest.
2. Disconnect and tee in the Smartboom harness.
3. Inspect the existing 12 pin armrest connector to determine if pin 12
is populated.
•If not populated, locate the single packard connector on the
armrest harness and tee in Smartboom harness. Master
switch sense is now connected and installation is
complete.
•If populated, installation is complete (master switch sense
is already connected internally to the Smartboom harness).
Connect single packard connectors on Smartboom
harness together to prevent contamination.

Rogator 864, 1064, 874, 1074 (Jan. 2006 & Newer) SmartBoom Installation Manual
4
4. Connect the power leads to a good source of switched power.
5. Refer to the Smartboom Operators manual for console setup
instructions.
Master switch tee-in if necessary

Manual # 016-1001-057
5

Rogator 864, 1064, 874, 1074 (Jan. 2006 & Newer) SmartBoom Installation Manual
6

Manual # 016-1001-057
7

Rogator 864, 1064, 874, 1074 (Jan. 2006 & Newer) SmartBoom Installation Manual
8

Raven Industries will not assume any expense or liability for repairs
made outside our facilities without written consent. Raven Industries
is not responsible for damage to any associated equipment or
products and will not be liable for loss of profit or other special
damages. The obligation of this warranty is in lieu of all other
warranties, expressed or implied, and no person or organization is
authorized to assume any liability for Raven Industries.
Damages caused by normal wear and tear, misuse, abuse, neglect,
accident, or improper installation and maintenance are not covered
by this warranty.
What Does this Warranty Cover?
How Long is the Coverage Period?
How Can I Get Service?
What Will Raven Industries Do?
What is not Covered by this Warranty?
Bring the defective part and proof of purchase to your Raven dealer.
If your dealer agrees with the warranty claim, the dealer will send the
part and proof of purchase to their distributor or to Raven Industries
for final approval.
Upon confirmation of the warranty claim, Raven Industries will, at our
discretion, repair or replace the defective part and pay for return
freight.
RAVENINDUSTRIES
Limited Warranty
This warranty covers all defects in workmanship or materials in your
Raven Applied Technology Division product under normal use,
maintenance, and service.
Raven Applied Technology Division products are covered by this
warranty for 12 months after the date of purchase. This warranty
coverage applies only to the original owner and is nontransferable.

Notice: This document and the information provided are the property of Raven Industries, Inc. and may only be used as
authorized by Raven Industries, Inc. All rights reserved under copyright laws.
Raven Industries
Applied Technology Division Toll Free (U.S. and Canada): (800)-243-5435
P.O. Box 5107 or Outside the U.S. :1 605-575-0722
Sioux Falls, SD 57117-5107 Fax: [phone]
www.ravenprecision.com www.ravenhelp.com
©Raven Industries, Inc. 2009, 2012
RoGator 864, 874, 1064 and 1074 (2006 & Newer)
SmartBoom™ Installation Manual
(P/N 016-1001-057 Rev B 2/12 E19243)