Razor eSpark User manual

OWNER’S MANUAL
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: The eSPARK must be traveling up to 3 mph before motor will engage. Kick
start up to 3 mph while applying the throttle to engage motor.
NOTE: Manual illustrations are for demonstration purposes only. Illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
v1_08_12
Please have your 19 digit product I.D. code ready before contacting Razor for
warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________

WARNING: Riding an electric scooter does present potential risks
and caution is required. Like any riding product, an electric scooter has
inherent hazards associated with its use (for example, falling off or riding
it into a hazardous situation). Like any riding product, electric scooters can
and are intended to move, and it is therefore possible to lose control or
otherwise get into dangerous situations. Both children and adults responsible
for supervising them must recognize that if such things occur, a rider can
be seriously injured or die, even when using safety equipment and other
precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
WARNING: PARENTAL AND ADULT
RESPONSIBILTY AND SUPERVISION IS NECESSARY:
Because products, like electric scooters, can and do present potential
hazards plainly associated with their use, it is well recognized THE NEED
FOR EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING RIDING
PRODUCTS APPROPRIATE TO THE AGE OF A CHILD, OR PARENTAL
SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES
MAY HAVE ACCESS TO THE SAME RIDING PRODUCTS, IS IMPORTANT.
Not every product is appropriate for every age or size of child, and different
age recommendations are found within this category of product which are
intended to reflect the nature of the hazards and the expected mental or
physical ability, or both, of a child to cope with the hazards.
The recommended rider age is 8 and older. Any rider unable to fit
comfortably on the scooter should not attempt to ride it. A parent’s decision
to allow his or her child to ride this product should be based on the child’s
maturity, skill and ability to follow rules.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the scooter.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions and to be able to
understand the hazards inherent in scooter use, should not use or be permitted
to use products inappropriate for their abilities. Persons with
heart conditions, head, back or neck ailments (or prior surgeries to these areas
of the body), or pregnant women, should be cautioned not to operate such
products.
DO NOT EXCEED THE WEIGHT LIMIT OF 120 lbs (54 kg). Rider weight
does not necessarily mean a person’s size is appropriate to fit or
maintain control of the scooter.
CHECK AND MAINTAIN SCOOTER CONDITIONS
Before use, check to confirm that any and all chain guards or other
covers and guards are in place and in serviceable condition. Check that
the brake is functioning properly, and that tires are inflated properly and
have sufficient tread remaining. The scooter should be maintained and repaired
in accordance with the manufacturer’s specifications, using
only the manufacturer’s authorized replacement parts, and should not
be modified from the manufacturer’s original design and configuration.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations, which may
affect the locations where the electric scooter may be used. Keep
safely away from cars and motor vehicle traffic at all times, and only
use where allowed and with caution.
Do not activate the speed control on the hand grip unless you are on the
scooter and in a safe, outdoor environment suitable for riding. The scooter
must accelerate to 3mph/5kmh for motor to engage.
The normal powered top speed of this scooter will be approximately 10 mph
(16 kmh), which can be affected by conditions, such as rider weight, inclines,
tire inflation and battery charge level. Avoid excessive speeds that can be
associated with downhill rides.
Maintain a hold on the handlebars at all times. Do not touch the brakes or
motor on your scooter when in use or immediately after riding as these parts
can become very hot.
Ride defensively. Watch out for potential obstacles that could catch your wheel
or force you to swerve suddenly or lose control. Be careful to avoid pedestrians,
skaters, skateboards, scooters, bikes, children or animals who may enter your
path, and respect the rights and property of others.
The electric scooter is intended for use on flat, dry surfaces, such as pavement
or level ground, without loose debris, such as sand, leaves, rocks or gravel.
Wet, slick, bumpy, uneven or rough surfaces may impair traction and contribute
to possible accidents. Do not ride your scooter in mud, ice, puddles or water.
Watch out for potential obstacles that could catch your wheel or force you
to swerve suddenly or lose control. Avoid sharp bumps, drainage grates, and
sudden surface changes.
Do not attempt or do stunts or tricks on your electric scooter. The scooter is not
made to withstand abuse from misuse, such as jumping, curb grinding or any
other type of stunts. Racing, stunt riding, or other maneuvers also enhance risk
of loss of control, or may cause uncontrolled rider actions or reactions.
Never allow more than one person at a time to ride the scooter.
Do not ride at night or when visibility is limited.
Never use near steps or swimming pools.
SAFETY WARNINGS
Safety Warnings ......................................................... 1-2
Before You Begin........................................................... 3
Assembly and Set-Up/Usage/Charging Battery.......... 4-5
Pre-Ride Checklist ......................................................... 6
1
Repair and Maintenance............................................. 6-9
Troubleshooting Guide................................................. 10
eSpark Parts ................................................................ 11
Warranty ...................................................................... 13
CONTENTS
WARNING: SPARKS CAN INDUCE FIRE
To reduce the risk of SERIOUS INJURY or FIRE:
PARENTS and RIDERS: Make sure riders understand that sparks can start
a fire. Keep sparks away from flammable or combustible substances. Use
only under close adult supervision.
BE RESPONSIBLE: Safety is important. Parents must review the following
warnings and instructions with each rider:
• For outdoor use only on solid, clean, dry, hardened surfaces. Keep sparks
away from substances that can catch fire, such as dry vegetation, paper,
chemicals or gasoline. Sparks can induce fire.
• Do not use in any area prone to wildres or posted by re authorities as a
Fire Hazard Zone.
• Never use your scooter to try to start a re. Your eSpark™ scooter emits
localized sparks when the Spark Bar on a moving scooter comes in contact
with hardened outdoor surfaces like asphalt or concrete. Be responsible.
• Do not ride at night.
• Keep sparks away from eyes, hair, exposed skin and clothing. Sparks can
burn.
• Spark Bar and cartridge get hot during use. Do not touch after use.
• Do not depress the Spark Bar continuously - only for short periods - while
the scooter is moving under power, as this may overheat components.
Always allow to cool (at least 15 minutes recommended) before replacing a
worn spark cartridge.
• Observe all other eSpark scooter safety warnings and instructions as
provided elsewhere in this manual.

2
Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product or back of charger) available for better assistance.
SAFETY WARNINGS
Do not allow hands, feet, hair, body parts, clothing, or similar articles to
come in contact with moving parts, wheels, or drivetrain, chain while the
motor is running.
Never use headphones or a cell phone to talk or text when riding.
Never hitch a ride with a vehicle.
Do not ride your scooter in wet or icy weather and never immerse the scooter
in water, as the electrical and drive components could be damaged by water
or create other possibly unsafe conditions. Never risk damaging surfaces,
such as carpet or flooring, by use of an electric scooter indoors.
PROPER RIDING ATTIRE
Always wear proper protective equipment, such as an approved safety
helmet (with chin strap securely buckled), elbow pads and kneepads. A
helmet may be legally required by local law or regulation in your area. A
long-sleeved shirt, long pants, and gloves are recommended. Always wear
athletic shoes (lace-up shoes with rubber soles), never ride barefooted or in
sandals, and keep shoelaces tied and out of the way of the wheels, motor
and drive system.
USING THE CHARGER
The charger supplied with the electric scooter should be regularly examined
for damage to the cord, plug, enclosure and other parts. In the event of such
damage, the scooter must not be charged until the charger has been repaired
or replaced.
Use only with the recommended charger.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from scooter when not in use.
Do not exceed charging time.
Always disconnect from the charger prior to wiping down and cleaning your
scooter with damp cloth.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS
INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE
CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION.

Remove contents from box. Remove the foam separators that protect the components from damage during
shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have
occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there
should not be any problems, even if the box has a few scars or dents.
MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY
OR MAINTENANCE PROCEDURES.
Estimated Assembly and Set-Up Time
Razor recommends assembly by an adult with experience in bicycle mechanics.
Allow up to 10 minutes for assembly, not including initial charge time.
Allow up to 12 hours for charge (see page 5 for charging information)
BEFORE YOU BEGIN
WARNING:
DO NOT USE NON-
RAZOR PARTS WITH
YOUR RAZOR ELECTRIC
SCOOTER.
The scooter has been built
to certain Razor design
specifications. The original
equipment supplied at the time
of sale was selected on the basis
of its compatibility with the
frame, fork and all other parts.
Certain aftermarket parts may
not be compatible and will void
the warranty.
Required Tools
Note: Electric scooter must
be moving at 3 mph/5 kmh
while applying the throttle
to engage motor.
Product ID Locations:
See locations to the left
1. Handlebar Stem
2. Battery Tray
3. Charger
4. UPC Side of Box (not shown)
5mm Allen Wrench
(Included)
3mm Allen Wrench
(Not Included)
8mm/10mm/13mm and
16mm Open Wrenches
(Not Included)
Phillips
Screwdriver
(Not Included)
Bicycle-style tire pump for
schrader valve tires with
pressure gauge
(Not Included)
3. Charger
(Note: Charger design may
vary from one shown)
Charger
Plug Charger
Port
3
Brake Lever
Twist Grip
Throttle
1. Handlebar
Stem
On/O Switch
Reset Button
- Battery
- Control Module
Limiter
Collar Clamp
Motor
Spark Bar
Spark Cartridge
2. Battery Tray

4
ASSEMBLY AND SET-UP
q Attaching the Handlebars
Tools required: 5mm Allen Wrench
q Inflating the Tire
The front tire is inflated when shipped, but it invariably may lose some pressure between the point of
manufacturing and your purchase. Always inflate tire to the correct PSI before first time use.
1Using a bicycle-style tire pump
equipped for a Schrader-type valve.
Inflate the front tire to the correct
PSI indicated on the sidewall of
the tire.
Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product or back of charger) available for better assistance.
2With the front wheel pointed straight
ahead and the handlebars square to the
front wheel, tighten the clamp as shown.
Tighten securely.
1 Loosen the collar clamp. With a
twisting motion, push and twist to slide
the handlebar stem onto the fork.
Note: Make sure the cables/
wires are out of the way before
inserting the stem into the fork.
WARNING: Failure to
properly tighten the collar clamp
may allow the handlebars to
dislodge while riding and may
cause you to lose control and
fall. When correctly tightened,
the handlebars will not rotate
out of alignment with the
front wheel, under normal
circumstances.
Note: The cable and wire
assembly from the handlebar
must not wrap around the
steering tube or handlebar.
Sharp bends or twisting of
the brake cable can cause the
brakes to malfunction.
WARNING:
Do not over inflate, as this
could damage tire or wheel.
Note: The pressurized air
supplies found at gasoline
stations are designed to inflate
high-volume automobile tires.
If you decide to use such an air
supply to inflate your electric
scooter tires, first make sure
the pressure gauge is working,
then use very short bursts to
inflate to the correct PSI. If you
inadvertently over-inate the
tire, release the excess
pressure immediately.
q Installing Spark Bar
1Using a 5mm Allen wrench, remove the
coupling bolt that is attached to the end of the
metal bar of the Spark Bar. Slide the Spark Bar
onto the metal bar as shown. Push to slide the
bar all the way on until the holes are aligned.
2Re-insert the coupling bolt through the
metal bar and tighten until Spark Bar is
locked securely into place.

5
USAGE
q Starting the Scooter
To start unit, turn on power switch; place both hands on handlebars and kick start the unit, using one
foot to push scooter forward while applying the throttle with right hand. The scooter must accelerate to
3mph/5kmh for motor to engage.
E100
E100
q Stopping the Scooter
To stop unit, release the throttle and apply the
brake until the unit comes to a complete stop.
Note: Electric scooter must
be moving at 3 mph/5 kmh
while applying throttle to
engage motor.
Note: As an additional safety
feature, the scooter is designed
to cut power to the motor when
the hand brake is applied.
CHARGING BATTERY
q Charging the Battery
Charge the battery prior to use.
LED Light
2Turn scooter power switch OFF
before charging. Plug the charger
into the charger port on the
electric scooter.
Charger
• Initial charge time: 12 hours
• Recharge time: up to 12 hours, even if the light
turns green. Recommended maximum charging
time is 24 hours.
• Always charge the battery immediately after
riding.
• Fully charge battery before storing for extended
periods of time.
• Unplug charger from the wall outlet when not
in use.
• Failure to recharge battery periodically may
result in a battery that will not accept a charge.
• Make sure scooter power switch is turned OFF
when unit is not in use. If the power switch is
left on for an extended period of time, the battery
may reach a stage at which it will no longer hold
a charge.
• To ensure long battery life, never store the product
in freezing or below freezing temperatures!
Freezing will permanently damage the battery.
• Run time: Up to 40 minutes of continuous ride
time. Run time may vary depending on riding
conditions, climate and/or proper maintenance.
• Constant stopping and starting may shorten
ride time.
• Average battery life for a properly maintained unit
is approx. 250 charge/discharge cycles.
Charger
Plug Charger
Port
1Plug the charger into a wall
outlet. If the lights on charger
do not light up, check the power
to the outlet. If necessary, try a
different outlet.
WARNING: Battery
charge can deplete over time.
Periodically recharge battery
when not in use.
WARNING:
Rechargeable batteries are
only to be charged under adult
supervision. Always disconnect
your scooter from the charger
before cleaning with damp cloth.
Note: If your charger does not
look like the one illustrated,
your unit has been supplied
with an alternative charger.
The specifications and charging
procedure would not change.
The charger has a small window
with one LED light to indicate
the charge status. Refer to the
illustration on the charger unit
for the actual “charging” and
“charged” status indications
for your model charger.
Chargers have built-in over-
charge protection to prevent
battery from being over-charged.
Charger may get warm during
use. This is normal for some
chargers and is no cause for
concern. If your charger does
not get warm during use, it
does not mean that it is not
working properly.
q Using the Spark Bar
When riding, place ball of foot on the Spark Bar
and gradually apply pressure. Only use enough
pressure to cause sparking action. Do not engage
the Spark Bar for extended or continuous periods
of use.

Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product or back of charger) available for better assistance.
PRE-RIDE CHECKLIST
Hardware
Check all parts, such as nuts, bolts, cables, fasteners, etc., to
ensure they are secure and assembled correctly. If the unit is
damaged, do not ride. Reference “Safety Warnings” on page 1
and 2 of this manual.
Laws and Regulations
Always check and obey any local laws or regulations.
Insurance
Do not assume that your existing insurance policies necessarily
provide coverage for scooter use. Check with your insurance
company for information regarding insurance.
Brake
Check the brakes for proper function. When you squeeze the lever,
the brake should provide positive braking action. Make sure that
brakes are not rubbing.
Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken frames
are rare, it is possible for an aggressive rider to run into a curb or
a wall and wreck, bend or break a frame. Get into the habit of
inspecting your scooter on a regular basis.
Tires
Periodically inspect the tires for excess wear and regularly check
the front tire pressure. Re-inate as necessary.
q
q
q
q
q
q
6
REPAIR AND MAINTENANCE
1To adjust brake cable play,
thread the brake lever adjuster in or
out 1/4 to 1/2 turn until the desired
brake adjustment is attained. Most
adjustments are complete at this
step. If brake still needs further
adjustment, proceed to step 2.
2 If brake is too tight or has too
much slack, use a 10mm wrench
to loosen the brake cable and
adjust accordingly.
3 Inspect the brake pads (A)
for proper alignment against
the wheel or excess wear. To
realign brake pads, loosen the
fixing nut (B) and adjust the pad
to contact the rim. Retighten
and readjust as needed. Verify
proper brake function prior to
riding the scooter.
q Adjusting the Brakes
Tools required: 10mm wrench
Turn power switch “OFF” before beginning repair or maintenance:
• Read the instructions
• Remove Charger Plug
• Turn the power switch off
• Secure the unit under repair
• Exercise caution around
exposed parts
• Contact Razor customer
service if unsure about
any repair or maintenance

7
REPAIR AND MAINTENANCE
q Chain and Rear Wheel Replacement
Tools required: Phillips screwdriver, 5mm Allen wrench and
two (2) 13mm wrenches.
2With a Phillips screwdriver,
loosen the two screws on the
chain guard and remove the
chain guard.
3Using two (2) 13mm wrenches,
loosen the locknuts by turning the
wrenches counter clockwise.
4 To loosen the chain, push the
tensioner down to create some
slack in the chain.
5 Remove wheel and install
replacement wheel. (Note the
sequence of the hardware)
6Push the chain tensioner
down to install the chain on
both sprockets.
1Using a 5mm Allen wrench,
remove the coupling bolt from
the Spark Bar and remove the
Spark Bar.
Note: Rear wheel hardware
sequence
E100 Rear Wheel Sequence
18-1 18-7
18-2 18-3
18-4
18-4
18-3 18-2
18-7
18-1
18-8
18-5
18-6
1 Using a 10mm wrench,
loosen the brake cable bolt.
q Front Wheel Replacement
Tools required: 10mm wrench and two (2) 16mm wrenches.
2Using two (2) 16mm wrenches,
loosen the locknuts by turning the
wrenches counterclockwise. Remove
wheel and install replacement wheel.
Reference front wheel hardware
sequence on this page.
3Reassemble, adjust and
tighten brake cable. Verify
proper brake function prior
to riding the scooter.
E1XX US VERSION
--- wheel hardware sequence
Front wheel hardware sequence
Rear wheel hardware sequence
Right Side (Throttle)
8-4 Spacer
8-3 Washer
Fork
8-3 Washer
8-2 Spring Washer
8-1 16 mm Locknut
Left Side (Brake)
8-4 Spacer
8-3 Washer
Fork
8-3 Washer
8-2 Spring Washer
8-1 16 mm Locknut
Middle
8-5 Front Axle Bolt
Note: Front wheel hardware
sequence
8-3
8-1
8-3
8-1
8-3
8-4
8-5
8-4
8-3
8-2 8-2

REPAIR AND MAINTENANCE
8
7With two (2) 13mm wrenches,
re-tighten the locknuts. 8Re-attach the chain guard.
q When to Replace the Spark Cartridge
Spark cartridge will continue to emit sparks until it is worn to the indicator line.
Indicator line
2Place a new cartridge in back of the bracket
making sure to align the slots on the cartridge
with the two legs of the bracket. Slide cartridge
forward until you hear a click and the thumb
tabs are locked into place.
1Using your thumbs, press tabs
(A & B) on both sides of the cartridge
to release from the bracket. Slide
cartridge away from you and remove
from bracket.
A
B
q Replacing the Spark Cartridge WARNING: Applying too
much pressure on the Spark Bar
may cause loss of control.
NOTE:Sparks and Spark
Cartridge life will vary based
on the amount of pressure
applied to the Spark Bar, the
length of time pressure is
applied, and the smoothness
of the riding surface.
WARNING: Do not
attempt to replace cartridge
immediately after riding as
cartridge will be hot. Handle only
when cool.
WARNING: Keep fingers
clear of Spark Bar hinge .
Friction during sparking will eventually wear out the replaceable cartridge and cause the scooter to stop making
sparks. Worn out cartridges must be replaced.
9Slide the Spark Bar onto the
metal bar located on the opposite
side of the chain. Push down on
the Spark Bar and slide the bar
all the way on until the holes
are aligned. Using a 5mm Allen
wrench reattach the Spark Bar. Right Side (Throttle)
18-4 Spacer (Short)
18-3 Washer (Plate Cut)
Frame
18-2 Washer
18-7 Spring Washer
18-1 13 mm Locknut
Left Side (Brake)
18-1 13 mm Locknut
18-7 Spring Washer
18-2 Washer
Frame
18-3 Washer (Plate Cut)
18-4 Spring
18-5 Housing
18-6 Spacer (Long)
Middle
18-8 Rear Axle Bolt
Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product or back of charger) available for better assistance.

q Battery Care and Disposal
Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery
life, carefully read the “Charging the Battery” section on page 5 of this owner’s manual.
CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED.
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an
environmentally safe manner. Do not dispose of a lead-acid battery in a re. The battery may explode or leak.
Do not dispose of a lead-acid battery in your regular household trash. The incineration, land lling or mixing of sealed
lead-acid batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or
state approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it
is prohibited by law to throw away lead-acid batteries in the municipal waste stream.
q Charger
The charger supplied with the electric scooter should be regularly examined for damage to the cord, plug,
enclosure and other parts. In the event of such damage, the product must not be charged until it has been
repaired or replaced.
Use ONLY the charger supplied with this product or a replacement specified by Razor.
q Wheels
Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically inspect
wheels for excess wear, and to adjust and replace drive train components as required.
q Replacement Parts
For the complete selection of replacement parts visit www.razor.com.
q Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Call 866-467-2967 for the center nearest you.
WARNING: If a battery
leak develops, avoid any contact
with leaking acid and place the
damaged battery in a plastic bag.
Refer to the disposal instructions at
left. If acid comes into contact with
skin or eyes, flush with cool water
for at least 15 minutes and contact
a physician.
WARNING: Battery
posts, terminals and related
accessories contain lead and lead
compounds. Wash your hands
after handling.
REPAIR AND MAINTENANCE
9

10
TROUBLESHOOTING GUIDE
Problem Possible Cause Solution
Does Not Work Out Of The Box Unit must be traveling up to 3 mph before
motor will engage
Loose connection(s)
Kickstart to 3 mph while applying the throttle to
engage motor
Check for loose connections/wires underneath
the deck plate
No Longer Works Loose connection(s)
Charger not working
Tripped reset button
Battery will not hold a charge
Check for loose connections/wires underneath
the deck plate
Check power to wall outlet and/or try a
different outlet
Check lights on charger:
Plugged into wall = Green
Plugged into wall & unit = Red = Charging
Charging Complete = Green
No lights/Blinking lights - Replace Charger
With no weight on the unit, carefully lift up the
back end; manually (and carefully, of course)
spin rear wheel and apply throttle to engage
the motor. If motor engages - Replace Battery
The reset button will trip if the motor is
overloaded. An excessive overload may be
caused, for example, by too heavy a rider,
too steep a hill, etc. Wait a few seconds then
press reset button. Correct riding conditions to
prevent overload
If motor does not engage, but makes a clicking
sound - Replace Battery. If motor does not
engage, no clicking sound - Replace Control
Module
Short Ride Time/Runs Slow Rider weight
Riding conditions
Battery not fully charged
Old/damaged battery
Tire is not properly inflated
Improper battery maintenance
Brake dragging
Do not exceed 120 lbs maximum weight limit
Use only on flat, dry surfaces. Avoid inclines
and areas with heavy debris
Charge unit for a full 12 hrs
With no weight on the unit, carefully lift up the
back end; manually (and carefully, of course)
spin rear wheel and apply throttle to engage
the motor. If motor engages - Replace Battery
Charge battery periodically when not in use
Tire will lose some pressure over time. Verify
correct tire pressure
Do not store unit in freezing or below freezing
temperatures. Freezing will permanently
damage the battery and greatly reduce ride
time. Refer to Page 5 Charging the Battery
Check the brake cable has 2-3 mm of slack at
lever. Cables should NOT be wrapped around
the handlebar stem. Adjust brake cable slack
according to page 6 instructions
Runs Intermittently Loose connection(s) Check the wires around the throttle and
connectors underneath the deck plate
Replace - Twist Grip Throttle
*Unit(s) should be turned off and fully charged prior to doing any Troubleshooting
NOTE: All troubleshooting steps should be performed by an adult only

Maintain your scooter with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specications
subject to change without notice.)
eSPARK PARTS
Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product or back of charger) available for better assistance.
01
02-1
02
03
04
01
05
06
07
08
09
10
11 12 13 14 15 16 17
18
19
20
21
22
23
24
25
01 Handlebar Grip (right/left)
02 Single Speed Twist Grip Throttle
02-1 Sleeve
03 Handlebar Stem
04 Brake Lever Assembly
05 Collar Clamp
06 Headset (upper/lower)
07 Limiter
08 Front Caliper Brake with Brake Pads
09 Front Fork
10 Front Wheel Complete
(See page 7 for hardware sequence)
11 Battery Tray
12 Control Module
13 On/Off Switch
14 Charger Port
15 Reset Button
16 Kickstand
17 Motor (24V/100W)
18 Rear Wheel Complete
(See page 7 and 8 for hardware sequence)
19 Chain Tensioner
20 Chain
21 Chain Guard
22 Battery (2) 24V/4.5 Ah
23 Deck Plate
24 Spark Bar
25 Spark Cartridge
11

12
SB1918(CALIFORNIA)DECLARATION
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS
INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO
DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR
INSURANCE COMPANY OR AGENT.

Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited Warranty
does not cover normal wear and tear, tires, tubes or cables, or any damage,
failure or loss caused by improper assembly, maintenance, storage or use of
the Razor eSpark.
This Limited Warranty will be void if the product is ever
• used in a manner other than for recreation or transportation
• modied in any way;
• rented.
WARRANTY
U.S. Design Patent D497,397 S
Printed in China for:
Razor USA LLC
PO Box 3610
Cerritos, CA 90703
Copyright © 2003-2012 Razor USA LLC. All rights reserved. RAZOR and the Razor Logo Design
are among the registered trademarks of Razor USA LLC in the United States and/or select foreign
countries.
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
__________________________________________
Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product or back of charger) available for better assistance.
13
08/2012