real living JC0802B User manual

TM
KID S ADIRONDACK CHAIR
’
ASSEMBLY INSTRUCTION
ITEM#: JC0802B
SKU#: 810587596
Need help? We are here for you!
1-800-935-3959 Toll Free or email us at [email protected]

Read all instructions before starting
Clear a flat covered space to begin
Always best to do it with a friend
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
Use the correct screws as indicated. All screws should be hand tightened until the complete piece is assembled ( This will make
the assembly process much easier ). Once the piece is fully assembled, then go back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the
product construction. Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging
branches, laundry line or electrical wires. Some parts may contain sharp edges.
When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury
and damage to the product. Please read all instructions before assembly and use.
The chair is not to be used for standing purposes. Use on even surfaces only.
The chair is used at weight of 110lbs (50kg). Improper use of this product or failure to use as directed may result in injury.
Not intended for commercial use.
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Before using, clean the product completely with a soft dry towel. Screws will be loosened over a period of usage, please check
the screws occasionally and re-tighten if necessary.

PARTS LIST
x1
Seat
x1
Left front leg
x1
Back
x1
Front cross bar
x1
Right front leg
x1
Right arm
x1
Left arm
AB
E
D
C
G
F
HARDWARE LIST
x8
Screw washer
x8
Hexagon Nut
x8
Machines screw
x4
Taping-Self Screw
x4
Barrel Nut
3
2
1
5
4
M6*45mm
1.77”
M6 M6*12mm
Ø 4*35mm
M6
x4
Machines screw
7
M6*50mm
2”
x1
Wrench
6

Important: Press a barrel nut (4) into
the hole in the part, making sure
the “-“ pattern is facing up.
Important: Using a standard screw
driver, turn the nut until the “-“ is
straight and the treaded hole is
facing outwards to accept the screw.
!
!
HELPFUL HINTS
· Tools needed, but not included:
· Separating parts before starting
How to install barrel nuts
4

STEP 1
Attaching left front leg(B) and right front
leg (C) to seat with 6 x part (1) and 6 x
part (2) and 6 x part (3) and wrench (6)
x6 x6
x6
12
2
Assembled View:
M6*45mm M6 M6*12mm
x6
3
3
x1
6
6
1
1
1
C
A
B

Attaching front cross bar (D) to legs
with 4 x part (5)
STEP 2
x4
5
Assembled View:
D
C
B
Ø4*35mm
5
5

STEP 3
Put 4 x part (4) into the hole of
back ( E), Make Sure the “-”is
aligned up the hole
x4
x4
4
Assembled View:
M6
4
E
4
4
4

STEP 4
Attaching chair back (E) to seat (A)
with 2 x part (7)
x2
7
Assembled View:
M6*50mm
E
7
7
A

STEP 5
Attaching left arm (F) and right arm (G)
to chair back and legs with 2 x part (1) and
2 x part (2) and 2 x part (3) and wrench (6)
and 2 x part (7)
Assembled View:
x2 x2
12
M6*45mm M6 M6*12mm
x2
3
x2
7
M6*50mm
x1
6
2
36
x2
F
B
C
E
G
7
7
1
2
3

STEP 6
Made in China