real living WESTBROOK A103001601 User manual

TM
Need help? We are here for you! 1(866)578 – 6569 24/7 • Toll Free
WESTBROOK 5X8 GRILL GAZEBO
ASSEMBLY INSTRUCTION
ITEM#: A103001601
SKU# 810452411

2/16
•Please read and understand this entire manual before attempting to assemble or install the product.
•Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
•The assembled gazebo should be located at least 6 feet from any obstruction such as fence, garage, house, overhanging
branches, laundry lines or electrical wires.
•Some parts may contain sharp edges. Wear protective gloves if necessary, during assembly.
•This unit is heavy. For safety, do not assemble this item alone. Two people are recommended for safe assembly.
•Check all nuts and bolts periodically for tightness and, when required, tighten them again.
•Pay attention to the parts orientation
• Install the gazebo on level ground.Stakes are provided to secure the gazebo to the ground.
• Do not assemble the gazebo on sandy, muddy or loose soil, as stakes do not have enough anchorage in these types of soil.
• If you wish to secure the gazebo to a wood deck or concrete surface, use anchors suited to these surfaces.
•Snow must be cleared off regularly during snowy days.Remove the snow at the roof top when it is thicker than 2 inches. In order to
avoid damage, use a plastic snow rake to remove excessive snow and ice buildup from roof and keep away from falling debris.
• Do not leave the gazebo where there is a risk of high wind, as possible damage will occur to the structure.
•Any assembly or maintenance of the product must be carried out by adults only.
• Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for installation and
use. Some special procedures may be valid in your area.
• Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that meets CPAI-84 specifications for
flame resistance. It is not fire proof. The fabric will burn if right in continuous contact with any flame source. The application of
any foreign substance to the tent fabric may render the flameresistant properties ineffective.
• If any scratch paint, please touch up to prevent rusting
• For outdoor use only.
WARRANTY:
WARNINGS:
• Steel components for this gazebo are treated with rust inhibiting paint that protects it from rusting. However, due to the nature
of steel, surface oxidation (rusting) will occur if these protective coatings are scratched. This is not a defect and thus not covered
by the warranty.
• To minimize this condition, it is recommended to use care when assembling and handling the product to prevent scratching the
paint. Should any scratching or damage occur, it is recommended to cover the scratch immediately with rust inhibiting paint
(not included).
•Surface rust can also be easily removed with a very light application of regular cooking oil or WD-40. If surface oxidation (rusting)
occurs and if no measure is taken to prevent this, the oxidation may start dripping onto deck or patio and caused damaging
stains, which may be difficult to remove. This can be prevented if the above-mentioned measures are taken to keep the product
from oxidizing.
• Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
• Keep instruction manual for future reference.
• Keep the original packaging to store the gazebo.
• Periodically check and ensure that all bolts are well-tighten during use
MAINTENANCE
GENERAL BEST PRACTICES FOR ASSEMBLY:
WHAT IS COVERED ?
The limited warranty is extended to the original purchaser and applies to material and manufacturer’s defect provided
the item is maintained with care and used only for personal, residential purposes.
Warranty: 1 Year

PARTS LIST
Label Part Number Description Qty Part Image
A P000200238 Post（1）2
B P000200239 Post（2）2
C P000500616 Small Top
Connector 1
D P000500617 Big Top
Connector 1
E P000601899 Slant Beam For
Small Roof4
F P000601900 Slant Beam For
Big Roof4
G P000400531 Long Screen 2
H P000400532 Short Screen 2
JP002100178 Table Top 1 1
K P002100179 Table Top 2 1
L P005800086 Big Hook 1
N P005800001 Hook 1
P P001100299 Small Canopy 1
Q P001100300 Big Canopy1
3/16

HARDWARE LIST
Label Part Number Description Qty Add Part Image
AA H010030030 Bolt M6*15 24 2
BB H050010025
Flat Washer
32 2
CC H010030023 Bolt M6*35 4 1
DD H040010004 Nut M6 4 1
EE H070010005
Stake ￠
6*230
8 0
FF H050020017
Spring
Washer M6
16 1
Z1 H090030002 Wrench M6 1 0
Z2 H090010017 Wrench M6 1 0
4/16
M6

HELPFUL HINTS
• Tools needed and not included
• Separating parts before starting
Provided in hardware pack
How many people needed for the installation work
5/16

STEP 1
Assembled View:
Secure short screen (H) to the post (A/B)
using bolt (AA), spring washer (FF) and flat
washer (BB), tighten with wrench (Z1),
cover with cup (GG).
6/16

STEP 2
Assembled View:
7/16
Secure long screen (G) to the post (A/B)
using bolt (AA), spring washer (FF) and flat
washer (BB), tighten with wrench (Z1),
cover with cup (GG).

STEP 3
Assembled View:
8/16
Secure the upper end of slant beam for
big foof (F) to the big top connector (G)
using push pin, then secure the lower end
to the post (A/B) using bolt (CC), washer
(DD) and nut (DD), tighten with wrench (Z1),
cover with cup (GG).

STEP 4
Assembled View:
9/16
Spead the big canopy (Q) to the roof, but do
not tighten at this step.

STEP 5
Assembled View:
10/16
Connect the slant beam for small roof (E) to
the small top connector (C) using push pin.

STEP 6
Assembled View:
11/16
Spread the small canopy (P) to the slant
beam for small roof (E) and tighten using the
4 corner pockects.

STEP 7
Assembled View:
12/16
Put the assmebled small roof to the big roof,
connect the slant beam for small roof (E) and
slant beam for big roof (F) using the push
pin. Screw the hook (N) to the big top
connector (D).

STEP 8
Assembled View:
13/16
Tighten the corner pockects without the pull
ring to the end of slant beam for big roof (F)
first, and then tighten the corner pockects
with the pull ring to the end of slant beam for
big roof (F).

STEP 9
Assembled View:
14/16
Secure the big hook (L) to the table top (K)
using bolt (AA) and washer (BB), tighten with
wrench (Z1) and cover with cup (GG).

STEP 10
Assembled View:
15/16
Lock the table top (J/K) to the U-plate of the
post (A/B) using bolt (AA) and washer (BB),
tighten with wrench (Z1) and cover with cup
(GG).

STEP 11
Assembled View:
16/16
Secure the gazebo to the ground using
stakes (EE).