real living LAKEWOOD GBO23-914SA User manual

LAKEWOOD ALL WEATHER WICKER 4PC SOFA SET
WITH CUSHIONS
ASSEMBLY INSTRUCTIONS
ITEM# : GBO23-914SA
SKU# : 810581106
Need help? We are here for you! 1-888-733-8169 Toll Free
Or email us at [e-mail],[e-mail]
[email protected]

GENERAL BEST PRACTICES FOR ASSEMBLY:
Read all instructions before starting
Clear a flat covered space to begin assembly
Always best to do it with a friend
Note that hardware required is provided for every step
Pay attention to orientation
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
WARNINGS:
Use the correct screws as indicated. All screws should be hand tightened until the complete piece is
assembled ( This will make the assembly process much easier ). Once the piece is fully assembled, then go
back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the
product construction.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or
electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use.
The products are not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
The sofa is used at weight of 350lb (159kg). The chair is used at weight of 250lb (113kg). Improper use of
this product or failure to use as directed may result in injury. Not intended for commercial use.
MAINTENANCE
STAIN RESISTANT CUSHIONS CARE —— KEEP THE CUSHIONS IN STORAGE ON RAINY DAYS.
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone.
Allow cushions to air dry.
FABRIC CARE: Hand wash cold, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.
ALL WEATHER WICKER PRODUCT CARE
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a
mild solution of soap and water, rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Screws can
be loosen over a peirod of usage, please check the screws occasionally and re-tighten if necessary.

PARTS LIST FOR SOFA
A
B
C
1PC Sofa Back 1PC Sofa Seat 4PC Sofa Leg
D1
D2
E
1PC Left Seat Cushion 1PC Right Seat Cushion 2PC Back Cushion
HARDWARE LIST
F
G
H
16PC Washer 12PC Screw(φ6x16mm) 4PC Screw(φ6x35mm)
I
1PC Allen Wrench
Warranty
One year limited warranty.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer's responsibility for freight and packing charges to and from the service center.

STEP 1
Secure sofa seat (B) to sofa back (A) with 4 screws (H) and
4 washers (F) by using allen wrench (I) .
Do not fully tighten now.
STEP 2
Secure sofa seat (B) to sofa back (A) to 4 legs (C) with 12
screws (G) and 12 washers (F) by using allen wrench (I).
Do not fully tighten now.
STEP 3
FULLY TIGHTEN ALL SCREWS NOW.
Put 2 seat cushions (D1,D2) and 2 back cushions (E) on the
sofa. The sofa is assembled.
A
B
I
H
C
C
C
D2
E
E
SECOND
FIRST
F
C
I
G
F
D1

PARTS LIST FOR 1 CHAIR
J
K
C
1PC Chair Back 1PC Chair Seat 4PC Chair Leg
M
N
1PC Seat Cushion 1PC Back Cushion
HARDWARE LIST FOR 1 CHAIR
F
G
H
15PC Washer 12PC Screw(φ6x16mm) 3PC Screw(φ6x35mm)
I
1PC Allen Wrench
Warranty
One year limited warranty.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer's responsibility for freight and packing charges to and from the service center.

STEP 1
Secure chair seat (K) to chair back (J) with 3 screws(H) and 4
washers (F) by using allen wrench (I) .
Do not fully tighten now.
STEP 2
Secure chair seat (K) to chair back (J) to 4 legs (C) with 12
screws (G) and 12 washers (F) by using allen wrench (I).
Do not fully tighten now.
STEP 3
FULLY TIGHTEN ALL SCREWS NOW.
Put 1 seat cushion (M) and 1 back cushion (N) on the chair.
The chair is assembled.
J
K
C
C
C
C
M
N
I
F
G
I
H
F
SECOND
FIRST

PARTS LIST FOR TABLE
L
M
N1
1PC Table Top 1PC Table Tray 2PC Table Leg
N2
U
2PC Table Leg 1PC Glass Top
HARDWARE LIST
F
G
H
12PC Washer 8PC Screw(φ6x16mm) 4PC Screw(φ6x35mm)
I
1PC Allen Wrench
Warranty
One year limited warranty.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer's responsibility for freight and packing charges to and from the service center.

STEP 1
Secure 1 table tray (M) to 4 table legs (N) with 4 screws (H) and 4
washers (F) using allen wrench (I).
Do not fully tighten now.
STEP 2
Secure 1 table top (L) to 1 table tray (M) and 4 table legs (N) with 8
screws (G) and 8 washers (F) using allen wrench (I).
Do not fully tighten now.
STEP 3
Place the table upside down and fully tighten all screws after making
sure it is stable. Then put 1 glass top (U) on it. The table is assembled.
L
U
I
F
H
I
F
G
N2
N1
N1
N2
The direction for the
leg steel plate is the
same as short side of
part (M).
M
Short side