Rebotec Augsburg User manual

REBOTEC®Rehabilitationsmittel GmbH
DE-49610 Quakenbrück, Artlandstr. 57-59
Telephone: [phone]-
Fax: [phone]
Web: www.rebotec.de
BA-Nr.: 01.07.085/2022-07-A01 Email: [e-mail]
Read this User Manual before using the device for the first time and keep it at hand for the
user as well as for future use and subsequent sales.
EN
User Manual
Shower and toilet wheelchair for
children
Figure similar
Augsburg
3 inches
Augsburg
4 inches
Augsburg
5 inches
339.03.97
339.04.97
339.05.97
80 kg
80 kg
80 kg

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 2 -
EN
Table of contents
1Product description .......................3
1.1 Introduction ............................................3
2Features ..........................................3
2.1 Intended purpose ...................................3
2.2 Conditions of use...................................3
2.3 Storage & transport................................4
2.4 Packaging ...............................................4
2.5 Disposal ..................................................4
3Symbols & nameplates..................4
4Safety instructions.........................4
5Incident reporting...........................5
6Warranty..........................................5
6.1 Complaint................................................5
7Reuse, lifetime................................5
8Scope of delivery............................5
9Setting up for use...........................6
9.1 Folding down the footrests...................6
9.2 Adjusting the footrest height................6
9.4 Attachment of height adapter for
footrest ..............................................................6
9.5 Assembling the backrest.......................6
9.6 Mounting the backrest cushion............6
10 Product data ...................................7
11 Operation of the product ...............7
11.1 Sitting down............................................7
11.2 Getting up ...............................................7
11.3 Swivelling the armrests.........................8
11.4 Parking brake operation........................8
11.5 Removing the footrests.........................8
11.6 Handling of the toilet bucket.................8
11.7 Removing the shower/ toilet seat.........8
11.8 Height adjustment of the backrest
cushion..............................................................8
12 Troubleshooting............................. 8
13 Care and maintenance................... 9
13.1 Cleaning and care.................................. 9
13.2 Maintenance ........................................... 9
14 Spare parts & accessories ......... 10
15 Drawing & dimensions ................ 11

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 3 -
EN
1 Product description
Figure shows:
A
Backrest
B
Armrest (swivelling)
C
Locking bolts
D
Chair frame with struts
E
Wheel insert with parking brake
F
PUR seat, hygiene opening
G
PUR seat cushion (removable)
H
PUR backrest cushion
I
Foot support with footrest (adjustable)
J
Bucket holder
K
Nameplate
1.1 Introduction
•The product described here is a medical device of
risk class I according to (EU) 2017/745 MDR.
•In this user manual, you will find information on the
safe and proper initial operation, use, maintenance
and care of this product.
•Carefully read this user manual before using the
device. Follow the safety instructions and act ac-
cordingly.
2 Features
2.1 Intended purpose
•The product is intended for the care of patients
with limited ability to stand and/or walk. It ensures
showering while sitting and going to the toilet, even
if a conventional toilet or bathroom is out of reach.
If designed appropriately, it can be slid over a con-
ventional toilet. The patient must have sufficient
sitting ability and upper body musculature. If nec-
essary, a nurse must be present during use. The
product is not intended for prolonged sitting and
transfer.
Specification
•For children
•Maximum user weight: 80 kg
•Height adjustable footrests
•Wheelchair, 4 swivel castors, lockable
•Indoor use
Indication
•If it is impossible for patients to visit a stationary
toilet, due to damage to the function of the lower
extremities with limited or eliminated mobility and
muscle strength and/or damage to the vestibular
functions or tendency to fall due to other causes,
while at the same time maintaining a sufficiently
stable thorax posture for sitting and sufficient re-
sidual functions of the upper extremities.
•The shower and toilet wheelchairs are intended
solely to assist in showering or bathing, toileting or
transferring a person indoors.
•Medical condition of the patient:
•The use of a chair by patients with cognitive disor-
ders (reduced mental, physical, sensory or intel-
lectual abilities) must be decided in advance by a
medical decision (prescription of the product) or on
site by the nursing personnel.
2.2 Conditions of use
•Temperature range: 5°C to 35°C; direct radiant
heat on the product must be avoided.
•Relative humidity: 40%-75%. Outside of these
conditions, the product must only be used for a
short time.
•The product is not suitable for use in swimming
pools or saunas, as surface discolouration and lim-
itations of mechanical strength may occur.
•Disassembly for transport or storage is possible.
A
B
D
E
H
I
C
F
K
J
G

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 4 -
EN
•There must be a flat surface of sufficient size for
the hoist to be placed on. See 15.
2.3 Storage & transport
•Temperature range: 5 °C to 25 °C; direct radiant
heat on the product must be avoided.
•Store the product in dry rooms with a humidity of
up to 65%.
•The shower should be designed so that there is a
flat surface of sufficient size.
2.4 Packaging
•We recommend you keep the packaging for a later
transport.
•Dimensions: 560mm x560mm x640mm
2.5 Disposal
•Disposal and recycling of used products and pack-
aging must be carried out in accordance with cur-
rently valid regulations. Please contact a disposal
company for further information.
•The Infection Protection Act must be observed.
•Please observe any labels and information on
packaging material and act accordingly.
3 Symbols & nameplates
Figure similar.
The nameplate must not be removed!
For ordering spare parts and processing
complaints, the device name, serial number and
year of manufacture will be required.
Symbol
Meaning
Symbol
Meaning
Read the
manual!
Year of
manufac-
ture of De-
vice
Serial num-
ber
Important
information!
Article num-
ber
Maximum
user weight
in kg
Symbol
Meaning
Symbol
Meaning
Care in-
structions
Mainte-
nance in-
structions
Applicable
for indoor
use only.
Manufac-
turer
Visual sig-
nal
Language
Read the
User Man-
ual!
Do not dis-
pose of as
household
waste.
Product complies with (EU) 2017/745
MDR
Caution!
Observe the safety instructions
Unique Device Identifier
(Data: GTIN / LOT (SN) / year of man-
ufacture)
Medical device label
This product is a medical device.
4 Safety instructions
Please observe the following safety in-
structions:
•Before using the device for the first time, the User
Manual must be read completely in order to avoid
hazards or damage caused by maloperation.
•Before each use, check the device for visible dam-
age or deficiencies.
•In case of malfunctions or damage of any kind, the
device must not be used.
Caution: Danger of falling!
•The chair must only be used with the armrests
locked in place when sitting and moving about.
•Sitting down, getting up, transferring of a patient
should be done under supervision or with the help
of a trained caregiver, depending on the patient's
state of health.
•Patients who are prone to uncontrolled actions or
movements must be supervised when using the
chair.
•The chair must only be moved on a slope or incline
with the help of a caregiver. Generally, on an uphill
slope the chair should be pushed forward and on
a downhill slope it should be pulled backward.
Caution: Danger of breakage!
EN

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 5 -
EN
•The product is only suitable for the intended use.
Observe the permitted user weight.
•Never carry or lift the product while a patient is sit-
ting on it.
•Do not pull or hold on to additionally attached com-
ponents or accessories.
Caution: Danger of tipping over!
•The chair must only be used with the armrests
locked in place when sitting and moving about.
•The chair must only be pushed by the push handle
(backrest).
•Only move the chair at a moderate walking pace
(with and without patients).
•Do not lean out of the chair (both in standstill and
while moving). If the swivel castors are in an unfa-
vourable position (pointing inwards), stability of the
chair is limited.
Caution: Danger of pinching or catching!
•When folding the armrests up or down, do not
reach into the joint guide so that no parts of the
body or other objects are trapped. To this end, also
see 9 on page 6.
•When attaching the seat plate, do not reach be-
tween the seat surface and the seat frame so that
no body parts are trapped.
•When pulling out and pushing in the toilet bucket,
there is a risk of trapping soft tissue of the patient.
To prevent injuries, the bucket may only be pulled
out or pushed in when no user is sitting in the chair.
Caution: Risk of injury!
•There is a risk of injury with surface temperatures
> 40°C. Therefore, do not expose the product to
high temperatures (e.g. sunlight, radiators, hot wa-
ter). Allow the product to cool down before use.
If the product is used by patients with in-
sensitive skin (no temperature perception
or skin damage), a heat check (e.g. touching with
the back of the hand) must be carried out by the
nursing staff.
5 Incident reporting
•Serious incidents in connection with the product
must be reported immediately to the manufacturer
and BfArM.
BfArM: www.bfarm.de/DE
▪Use the reporting functions and provided
forms.
Manufacturer: [e-mail]
6 Warranty
•For this product the manufacturer grants a war-
ranty of 12 months. Compliance with the general
terms and conditions(www.rebotec.de/agbs), as
well as the intended use, are a basic prerequisite.
The statutory warranty provisions shall apply.
•Unauthorised modifications to this product will void
the product’s conformity and the warranty.
6.1 Complaint
•Please contact us before returning the product.
•To reduce transport damage, use the original
packaging if possible.
•The Infection Protection Act must be complied
with.
Please make sure that the product does not
pose a risk of infection when returned.
Enclose the information sheet on safety with the
product.
Costs may incur for returns that are not marked
non-objectionable.
7 Reuse, lifetime
•The product is suitable for reuse. How often the
product can be reused depends on the frequency
and nature of use.
•Before reuse, the product must be reprocessed hy-
gienically and the technical and functional safety
and reliability of the product must be checked and
restored if necessary. See 13.
For more detailed information, please see the
reprocessing instructions (02.12.156) and the
maintenance instructions (02.11.150).
The documents can be downloaded from the fol-
lowing link.
▪www.rebotec.de/downloads
•If the product is used as intended, its lifetime is 5
years. The effective lifetime may vary depending
on the frequency and intensity of use and the gen-
eral condition.
8 Scope of delivery
•1x shower / toilet wheelchair
1x toilet bucket
2x Height adapters
•1x user manual (02.07.085)
•1 Allen key

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 6 -
EN
•The reprocessing and maintenance instructions
can be ordered or viewed and downloaded at
www.rebotec.de/downloads.
9 Setting up for use
•The product has been carefully inspected in the
factory for freedom from defects and complete-
ness. Please check the product for any possible
damage which may have occurred during transport
and for completeness of the scope of delivery upon
receipt. Assembly or adjustment shall be carried
out by the specialist dealer
9.1 Folding down the footrests
•Turn (1) the footrests forwards until they engage
automatically. Fold (2) the footrests down. Adjust
the height of the footrests if necessary.
9.2 Adjusting the footrest height
•The footrest height can be adjusted in 7 positions.
Loosen and remove the screws on the side of the
footrest using an Allen key (SW 5). Select the ap-
propriate height level (1-7) and screw the footrest
back in place. Make sure that the screws are firmly
tightened!
9.4 Attachment of height adapter for
footrest
•To reduce the space between footrest and seat
even more, an additional height adapter can be at-
tached between the front wheel insert and the
swivel arm of the footrest.
•The height adapter can be installed either below
(1) or just above (2) the frame strut.
•When installing the
adapter, make sure that the
recess (1) faces upwards
so that the footrest can
latch in properly.
•With the Augsburg
chair with 3” wheels, the two height adapters for
the footrest are pre-installed to avoid floor contact
with the footrest set to maximum height. With other
variants, both height adapters can be installed as
required.
9.5 Assembling the backrest
•Swivel the armrests
backwards, place the
backrest on the tubes of the
chair frame and push it onto
the base frame as far as it will
go.
•Swivel the armrests
forwards again so that they engage in the groove
on the backrest and with the locking bolt in the
base frame.
9.6 Mounting the backrest cushion
•The backrest cushion is attached to the cross strut
of the backrest. (1&2)
2
1
Min
Max
1
1
2

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 7 -
EN
10 Product data
•We reserve the right to make technical develop-
ments and improvements with respect to the de-
sign shown in this User Manual.
•See 15.
Characteristic
Value
Augsburg 3 inches
1.
User weight
80 kg
2.
Product weight*
16.4 kg
3.
Total weight*
19.0 kg
Skin compatibility
DIN EN 10993-1/-5
Characteristic
Value
Augsburg 4 inches
1.
User weight
80 kg
2.
Product weight*
16.8 kg
3.
Total weight*
19.4 kg
Skin compatibility
DIN EN 10993-1/-5
Characteristic
Value
Augsburg 5 inches
1.
User weight
80 kg
2.
Product weight*
17.2 kg
3.
Total weight*
19.6 kg
Skin compatibility
DIN EN 10993-1/-5
Without accessories
11 Operation of the product
•Before use, it must be ensured that the product is
in proper condition. If defects or malfunctions are
evident, the product must not be used. Have the
defects corrected by a specialist dealer before use.
If necessary, depending on the patient's
limitations (adequate mobility and muscle
strength), sitting down and getting up must
be done with the help of a caregiver. Subsequent
adjustments may only be made by qualified per-
sonnel.
11.1 Sitting down
•Before sitting down and standing up, make sure
that the product is securely positioned to prevent it
from slipping or tipping over, that at least two
wheels are braked, that the armrests are properly
engaged, that the seat surfaces are firmly in place,
and that the footrests are folded to the side or up.
•The user must posi-
tion themselves as close
as possible to the product.
If necessary, they can ori-
entate or support them-
selves with their hands on
the armrests.
•If this is not possible
due to their physical limitations, the user must seek
the assistance of a competent person. This can be
with the help of an assistive device
Attention: Danger of falling!
•Falling down or slumping on
the chair seat must be avoided.
The patient should sit on the full
chair surface, if possible, and
not only on the edge of the seat
•When transporting people,
the entire surface of the
backrest and the footrests must
be used if possible.
11.2 Getting up
•Before standing up, make sure that the product is
securely positioned to prevent it from slipping or
tipping over, that at least two wheels are braked,
that the armrests are properly engaged, that the
seat surfaces are firmly in place, and that the foot-
rests are folded to the side or up.
•The patient must move forward on the chair so that
their feet are on the floor.
•The patient must support themselves with their
arms on the armrests and slowly rise from the seat.
•Do not lean your body too far
forward to avoid a potential risk
of falling.
•The patient should be helped
to stand up by the nursing staff
Caution: Danger of falling!
2.
3.
1.
1
2

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 8 -
EN
•The patient must
never leave their feet on
the footrests when sitting
down or getting up.
11.3 Swivelling the armrests
•Pulling out the locking bolts (A) releases the lock-
ing mechanism and the armrests can be swivelled
backwards.
•When folding up the armrest, check that the catch
on the backrest (B) and the locking bolt (A) are
seated correctly.
Caution: Danger of pinching or catching!
•The armrests can be swivelled with both hands. To
do this, keep the locking bolt (A) pulled during the
entire swivelling process and guide the armrest to
point (C) with the other hand.
•Only touch the outer area and do not reach into or
through the armrest.
Check the locking at regular intervals, as
possible limescale deposits on the locking
mechanism can impair function and smooth opera-
tion.
11.4 Parking brake operation
•With your foot, press down the parking brake lever
(1). The wheel is now braked and fixed in its direc-
tion. The wheel is released by lifting the actuating
lever with the foot (2).
11.5 Removing the footrests
•Remove or fold up the seat. Then, raise the foot-
rest by approx. 100 mm and turn outwards by 90
degrees.
•Now you can push the footrest all the way up and
pull it out
11.6 Handling of the toilet bucket
•From the back of the chair, slide the toilet bucket
under the seat. To remove, slightly lift the bucket
and then pull it out backwards.
•In the version with a 2-section toilet seat, you can
alternatively insert or remove the toilet bucket from
above by lifting the seat.
11.7 Removing the shower/ toilet seat
•The seat can be removed from its locked position
on the chair frame by lifting it off for cleaning or
replacement.
11.8 Height adjustment of the backrest
cushion
•The backrest cushion is attached to the cross strut
of the backrest. It can be adjusted in two fixed
heights. By loosening the screws, the backrest
cushion can be adjusted by 80 mm.
12 Troubleshooting
Fault
Potential cause
Remedy
Armrest can-
not be swiv-
elled down
Deposits in the
locking device
(locking bolt)
Cleaning,
checking
regularly
Locking bolt
cannot be
pulled out
Deposits, tension
spring jammed or
defective
Cleaning,
Replace
the locking
bolt
Footrest can-
not be folded
down
Deposits in the
joint,
Bracing
Cleaning,
Check
screw con-
nection
Wheel lock
does not
brake
General defect
see mainte-
nance!
2
1
4.
C
B
A

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 9 -
EN
Fault
Potential cause
Remedy
Turning the
wheel is stiff
Deposits
Cleaning
Wheel does
not turn
General defect
see mainte-
nance!
Uneven run-
ning of the
wheel
Severe uneven
tread wear
see mainte-
nance!
Chair frame
too unstable
Screw connections
too loose
Screw con-
nections:
Tighten
frame,
wheel in-
serts
Wheel insert
bent/dis-
torted
Hitting an obstacle
see mainte-
nance!
13 Care and maintenance
13.1 Cleaning and care
The product can be cleaned using a mild
conventional cleaning and disinfecting
agent. After cleaning, wipe the product with a clean,
moist cloth and then wipe it dry with a dry cloth.
•Do not use scouring agents or cleaning agents
with aggressive ingredients (acids, thinners), as
well as hard cleaning objects (brushes), as other-
wise the surfaces may be damaged or deposits
may form on the materials.
Keep the product clean and clean it regu-
larly. Special attention must be paid to hy-
giene in the sensitive areas.
•The product is suitable for manual cleaning and
disinfection. Please observe the reprocessing in-
structions (02.12.156).
13.2 Maintenance
•Wear and tear that is not recognised in time and/or
improper handling, as well as irregular or no
maintenance may result in accidents.
For safety reasons, the product must be
professionally maintained at least once a
year.
•Check product for visible damage
(cracks, breakage, loose parts)
•Check stability before use
Maintenance/inspection scope
•Maintenance should include the following in-
spection work and should be documented.
•All bolted connections for tightness (espe-
cially the wheel inserts and the frame)
•Function of the armrests and locking bolts
•Function of the footrest (replace defective
footrests)
•Running characteristics and tread of the
wheels (replace defective wheels)
•Function of the parking brakes (replace defec-
tive brakes)
•Inspect accessories for deficiencies
Repair
•If you have any questions concerning the
maintenance of the chair, please contact an
authorised dealer or a medical and healthcare
supplies store.
•In the event of damage and/or repairs, contact
your authorised dealer immediately.
•Never make any unauthorised modifications
or conversions to the chair. These will only
adversely affect the safety and functioning of
the chair.
•Only use OEM spare parts by the manufac-
turer REBOTEC for repairs. Observe all guar-
antee and warranty information.
•After maintenance or repair work has been
carried out we recommend you clean the de-
vice for hygienic reasons before using it
again.
•Follow all the instructions for ordering spare
parts, reuse and the lifetime.
For documenting the maintenance and
repair work, REBOTEC provides a
Maintenance Report. The operating in-
structions and maintenance log can be ordered or
viewed via www.rebotec.de. It is also possible to
print the information and read it when needed.

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 10 -
EN
14 Spare parts & accessories
No.
Art. no.
Designation
1
301.44
Toilet bucket, standard
2
309.10
Bucket holder
3
440.10.01
PUR shower seat padding
4
446.00.81
Wheel with brakes, for toilet chairs
5
450.10.05
Armrest engagement lock, complete
6a
447.XX.57
Footrest complete, left
6b
447.XX.59
Footrest complete, right
7
445.10.02
PUR backrest cushion
-
444.00.97
Adjustment of the seat width & depth
-
444.03.39
Headrest unit
-
440.54.67
Adapter for height adjustment of the legrests
-
02.07.085
User Manual
-
02.11.150
Maintenance log
-
02.12.156
Reprocessing Instructions
XX= Colour variant
Use only REBOTEC spare parts and accessories to ensure the proper and safe functioning of the
device. Subject to change without notice.
1
3
5
4
1
2
3
4
6a/b
7
5

REBOTEC / BA-Nr.: 01.07.085/2022-07-A01
- 11 -
EN
15 Drawing & dimensions
No.
Designation
3” wheel dimensions
/ mm
4” wheel dimensions
/ mm
5” wheel dimensions
/ mm
A
Height
1080
1110
1130
B
Width
520
520
530
C
Depth
870
870
870
D
Seat height
500
540
560
E
Seat width
420
420
420
F
Seat depth
420
420
420
G1
Slide-over height
390
420
440
G2
Slide-over height
330
330
330
H*
Knee height of footrest
max.
250-440
380-540
380-540
I
Armrest height
765
765
765
J1
Front castor diameter
75
100
125
J2
Rear castor diameter
75
100
125
*Take into account the height adapter
Dimensions and weights may vary depending on the equipment. There might be minor deviations due
to production tolerances. Subject to change without notice.

Read this User Manual before using the device for the first time and keep it at hand for the
user as well as for future use and subsequent sales.
REBOTEC®
Rehabilitationsmittel GmbH
D-49610 Quakenbrück, Artlandstr. 57-59
Telephone: [phone]
Fax: [phone]
Web:
www.rebotec.de
Email:
[email protected]
EN