Record K 32 M User manual

record K 32 M / K 42 M
User manual
Your global partner for entrance solutions www.record.group

Document identification
Article nr.: 121-006454677
Version: 1.1
Publication date: 05/07/2022
Translation of the original manual
Subject to technical modifications
Copyright © agtatec ag

Table of Contents
BAL_K32_K42_M_EN_1V1_REC_121-006454677 3 / 24
Table of Contents
List of changes ................................................................................................................................................. 4
1 Safety................................................................................................................................................................. 5
1.1 Presentation of warning signs............................................................................................................... 5
1.2 Intended purpose of use ....................................................................................................................... 5
1.3 General hazards ................................................................................................................................... 6
1.4 State of technology ............................................................................................................................... 8
1.5 Personal protective equipment ............................................................................................................. 8
1.6 Spare parts and liability ........................................................................................................................ 9
2 General information ......................................................................................................................................... 10
2.1 Purpose and use of the instructions ..................................................................................................... 10
2.2 Copyright .............................................................................................................................................. 10
2.3 Product identification ............................................................................................................................ 10
2.4 Manufacturer BLASI GmbH .................................................................................................................. 10
2.5 Target groups ....................................................................................................................................... 10
2.6 Definition of terms................................................................................................................................. 11
3 Description........................................................................................................................................................ 12
3.1 Graphical display .................................................................................................................................. 12
3.1.1 Main mechanical components ......................................................................................................... 12
3.2 Description of the manual revolving door ............................................................................................. 13
3.3 Safety features...................................................................................................................................... 13
3.3.1 Safety strips on turnstile wings ........................................................................................................ 13
4 Options .............................................................................................................................................................. 14
4.1 Lighting control ..................................................................................................................................... 14
4.2 Speed control........................................................................................................................................ 14
4.3 Foldable turnstile wings and/or foldable drum walls ............................................................................. 14
4.4 Turnstile lock mechanisms ................................................................................................................... 15
4.4.1 Electromagnetic turnstile lock .......................................................................................................... 15
4.4.2 Electromagnetic turnstile lock (Fail Secure)..................................................................................... 15
4.4.3 Turnstile bar-bolt lock....................................................................................................................... 16
4.4.4 Turnstile corner lock......................................................................................................................... 16
4.5 Night shield variations........................................................................................................................... 16
4.5.1 Manual night shield .......................................................................................................................... 16
4.5.2 Night shield - deadman .................................................................................................................... 16
5 Specifications ................................................................................................................................................... 17
5.1 Environmental conditions...................................................................................................................... 17
5.2 Electrical connection data (optional)..................................................................................................... 17
6 Servicing and maintenance ............................................................................................................................. 18
6.1 General remarks ................................................................................................................................... 18
6.2 Monthly inspection work performed by the operator............................................................................. 18
6.3 Cleaning and care................................................................................................................................. 19
7 Malfunctions ..................................................................................................................................................... 21
7.1 Conduct during malfunctions ................................................................................................................ 21
7.2 Tips for troubleshooting ........................................................................................................................ 21
8 Taking out of service and disposal................................................................................................................. 22
8.1 Decommissioning ................................................................................................................................. 22
8.2 Dismantling and disposal...................................................................................................................... 22

List of changes
4 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
List of changes
Change Location
Complete revision of all Sections and content Entire document
New Section structure Entire document
Revision of all graphics Entire document

Safety 1
BAL_K32_K42_M_EN_1V1_REC_121-006454677 5 / 24
1 Safety
1.1 Presentation of warning signs
Various symbols are used in this guide for easier understanding:
NOTICE
Useful advice and information to ensure correct and efficient workflow of the system.
IMPORTANT
Specific details which are essential for trouble-free operation of the system.
IMPORTANT
Important details which must be read for proper function of the system.
CAUTION
Against a potential hazardous situation that can lead to minor personal injury and property
damage.
WARNING
Against a latent hazardous situation that can lead to severe injuries or death and cause sub-
stantial property damage.
DANGER
Against an imminent hazardous situation that can lead to severe injury or death.
DANGER
Against an imminent or latent hazardous situation that could lead to electric shock and cause
serious injury or death.
1.2 Intended purpose of use
The system is designed exclusively for use as a pedestrian passage. The installation must only occur
in dry areas. If there are deviations then proper waterproofing and water drains will be required on-
site.
Any other application or use beyond this purpose is not considered to be an intended purpose. The
manufacturer bears no liability for any resulting damage; the operator alone shall bear the associated
risk.
The intended purpose also includes observation of the operating conditions specified by the manufac-
turer, in addition to regular care, maintenance and repair.
Interventions in or alterations to the installation performed by non-authorized maintenance technicians
exclude the manufacturer's liability for consequential damages.

1Safety
6 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
1.3 General hazards
The following section lists hazards that can be caused by the system even when used as intended.
To reduce the risk of malfunction, damage to property or injury to persons and to avoid dangerous
situations, the safety instructions listed here must be observed.
The specific safety instructions in the other sections of this manual must also be observed.
IMPORTANT
The country-specific regulations must be observed and complied with!
IMPORTANT
To avoid malfunctions, moving objects such as flags or parts of plants must not be allowed to
enter the detection range of the sensors.
CAUTION
Risk of malfunctions, material damage or injury due to improper settings!
a) Improper settings can lead to malfunctions, material damage or personal injury.
ðDo not disconnect the system from the power supply overnight.
ðSettings should only be made by personnel qualified to do so.
ðDo not disassemble, put out of operation or manipulate safety devices.
ðHave faults rectified by specialist personnel or by personnel qualified to do so.
ðHave service and maintenance carried out according to locally applicable regulations or accord-
ing to a maintenance contract.
CAUTION
Risk of malfunctions, material damage or injuries due to insufficient or missing cleaning or
care!
a) Insufficient or inattentive cleaning or care of the system can lead to malfunctions, damage to
property or injury to persons.
ðCheck the sensors regularly for dirt and clean them if necessary.
ðRegularly remove dirt accumulations in the floor rail or under the floor mat.
ðKeep the system free from snow and ice.
ðDo not use aggressive or caustic cleaning agents.
ðUse road salt or loose chippings only conditionally.
ðLay the floor mat without folds and flush with the floor.
ðEquipment required for cleaning purposes such as ladders or similar must not be leaned on or at-
tached to the system.

Safety 1
BAL_K32_K42_M_EN_1V1_REC_121-006454677 7 / 24
CAUTION
Risk of material damage or injury due to unforeseen opening, closing or turning of the door!
a) The door can open, close or turn unexpectedly. This may result in damage to property or injury
to persons.
ðNo persons may be present in the opening area of the system.
ðEnsure that moving objects such as flags or parts of plants do not enter the detection range of
the sensors.
ðDo not make any settings on the control unit when the system is in use.
ðHave faults rectified immediately by specialist or personnel qualified to do so.
ðRemove objects from the opening area.
ðDo not disassemble, put out of operation or manipulate safety devices.
ðDo not rush through a closing system.
CAUTION
Risk of bruising and severing of limbs!
a) If the system moves, careless behaviour can lead to serious injuries to limbs or severance of
limbs.
ðDo not reach in when parts of the system are moving.
ðKeep a distance when parts of the system move.
ðDo not bump into or touch the system when it is moving.
ðDo not open or remove protective covers during operation.
ðDo not permanently remove covers from the system.
ðOnly carry out inspection, service, maintenance and cleaning when the system is stationary and
switched off.
CAUTION
Danger of material damage or injury due to non-functioning safety devices!
a) If safety devices are not functioning, manipulated or put out of operation, there is a risk of dam-
age to property or injuries that can lead to death.
ðNever disable or manipulate safety devices.
ðHave inspection, service and maintenance of the safety devices carried out according to local
regulations or according to a maintenance contract.
CAUTION
Danger of malfunctions, damage to property or risk of injury if used by unauthorised persons!
a) If unauthorised persons use the system, there is a risk of malfunction, damage to property or in-
jury to persons.
ðChildren under 8 years of age may only use the system under supervision.
ðChildren must not play, clean or maintain the system.
ðPersons with limited physical, sensory or mental abilities as well as persons with insufficient
knowledge or experience may only use the system under supervision or must have received and
understood instructions to do so.

1Safety
8 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
DANGER
Danger to life due to electric current!
a) In case of contact with live parts, there is an immediate danger to life due to electric shock.
Damage to or removal of the insulation or individual components can be life-threatening.
ðBefore starting work on active parts of electrical systems and equipment, ensure that all poles are
voltage free and that this is maintained for the duration of the work.
ðKeep moisture away from live parts. This can lead to a short circuit.
ðNever bridge fuses or put them out of operation.
ðDo not connect the power supply until all work has been completed.
ðHave work on the electrical system performed by qualified personnel only.
DANGER
Danger to life due to non-functioning safety devices of the fire protection system!
a) If safety devices of the fire protection system do not function properly, there is a risk of serious
or fatal injuries.
ðNever disconnect the fire protection system from the power supply overnight.
ðDo not disassemble, put out of operation or manipulate safety devices.
ðDo not remove safety instructions on the system.
ðNever block, hold open or otherwise prevent fire doors from closing.
ðHave inspection, service and maintenance of the fire protection system carried out in accordance
with locally applicable regulations or according to a maintenance contract.
ðHave the fire protection system checked and maintained according to the state of the art.
1.4 State of technology
This system was developed using state of the art technology and officially recognized technical safety
regulations. The system, depending on its options and diameter, comply with the requirements of the
Machine Guidelines 2006/42/EG as well as EN 16005 and DIN 18650 (D).
Nevertheless, danger may arise if not used as intended.
IMPORTANT
Installation, commissioning, inspection, maintenance and repair work may only be conducted
by qualified, trained and authorized technicians.
After commissioning or repair work, fill in the check list and give it to the customer for safe
keeping.
We recommend obtaining a service agreement.
1.5 Personal protective equipment
Personal protective equipment is used to protect persons from adverse effects on health. Personnel
must wear personal protective equipment during the various work activities on and with the system.
Personal protective equipment is explained below:
Hearing protection is used to protect the hearing from noise. As a rule of
thumb, hearing protection is compulsory from when normal conversa-
tion with other people is no longer possible.

Safety 1
BAL_K32_K42_M_EN_1V1_REC_121-006454677 9 / 24
The head protection serves to protect against falling and flying parts
and materials. It also protects the head from bumping into hard objects.
Protective goggles protect the eyes from flying parts, dust, splinters or
splashes.
Protective gloves are designed to protect hands from friction, abrasions,
punctures or serious injury and from burning caused by contacting hot
surfaces.
Safety shoes protect the feet from crushing, falling parts and slipping on
surfaces. The puncture resistance of the shoes ensures, that pointy ob-
jects do not penetrate the foot.
The high-visibility vest is used to make the personnel stand out and
therefore to be seen. With improved visibility and attention, the high-vis-
ibility vest protects personnel in busy work areas from collisions with
vehicles.
Depending on the place of work and the working environment, the protective equipment varies and
must be adapted accordingly. In addition to protective equipment for specific work, the work site may
require other protective equipment ( for example a harness).
In hygiene-protected areas, special or additional requirements of personal protective equipment may
be required. These requirements must be considered when choosing personal protective equipment.
If there is any uncertainty regarding the choice of personal protective equipment, the safety officer
must be consulted at the place of work.
1.6 Spare parts and liability
Reliable and trouble free operation of the door is only guaranteed when using parts that were recom-
mended by the manufacturer. The manufacturer declines any liability for damages resulting from un-
authorized modifications to the door or the use of parts that are not permitted.

2General information
10 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
2 General information
2.1 Purpose and use of the instructions
These instructions are an integral part of the system and enable efficient and safe handling of the sys-
tem. In order to ensure proper functioning, the instructions must be accessible at all times and kept in
the immediate area of the system.
Although only the male form has been chosen for reasons of better legibility, the information refers to
members of both sexes.
The operator must have read and understood the manual before starting any work. The basic require-
ment for safe working is to follow the safety instructions and the handling instructions. In addition, the
local regulations and safety rules apply.
The manual can be handed over in extracts to instructed personnel who are familiar with the opera-
tion of the system.
The illustrations are for basic understanding and may differ from the actual presentation. Specific rep-
resentations are contained in the drawings.
2.2 Copyright
The copyright of the instructions remain at:
BLASI GmbH
Carl-Benz-Str. 5-15
D – 77972 Mahlberg
It is prohibited to reproduce, distribute or use the manuals for purpose of competition without the writ-
ten authorization of BLASI GmbH.
Violation of the here stated copyrights will be prosecuted and fined with compensation of damage.
Subject can change without prior notice.
Differences between product and manual are thereby possible.
2.3 Product identification
The nameplate located on the door provides accurate identification of the product.
2.4 Manufacturer BLASI GmbH
BLASI GmbH Automatic Door Systems
Carl-Benz-Str. 5-15
D-77972 Mahlberg
Germany
Telephone: [phone]
Fax: [phone]
2.5 Target groups
CAUTION
Risk of injury if personnel are insufficiently qualified!
If unqualified personnel work on the system or are in the danger zone of the system, dangers may
arise which can cause serious injuries and considerable damage to property.
a) All work must be carried out by qualified personnel only.
b) Keep unqualified personnel away from danger areas.
This operating manual is intended for the target groups listed below:
– Operating entity of the system:
the person who is responsible for the technical maintenance of this system
– Operator of the system:
the person who operates the system every day and has been suitably instructed

General information 2
BAL_K32_K42_M_EN_1V1_REC_121-006454677 11 / 24
2.6 Definition of terms
Term: Explanation:
System The term is also used in these instructions as a synonym for the
product. Door operators, revolving doors, sliding doors, etc. are re-
ferred to as a system.
If information in these instructions refers to a specific type, this is
shown accordingly in the text.
User Users are all persons who use the system.
System operator The respective owner is referred to as the system operator, regardless
of whether they operate the system as the owner or pass it on to third
parties.
Authorized representative The authorized representative takes over certain parts of the manufac-
turer's obligations with regard to fulfilling the requirements of the Ma-
chinery Directive. In particular, the authorized representative may also
place the system on the market and/or sign EC declarations of incor-
poration.
Qualified personnel Qualified personnel are authorized and appropriately trained to perform
the following work:
– Disassembly, Assembly, Commissioning, Operation, Audit, Main-
tenance, Troubleshooting, Decommissioning
The qualified personnel have several years of professional experience
in the technical field, e.g. as mechanics or machine fitters.
The qualified personnel are aware of the residual risks arising from the
installation site and, due to their professional training, knowledge and
experience, are able to carry out the work assigned to them and to in-
dependently identify and avoid possible danger points.
Manufacturer The manufacturer is whoever designs and/or builds machinery or in-
complete machinery under the scope of the Machinery Directive.
Life phases All phases of the system's condition and use are referred to as life
phases. This applies from the time the system leaves the factory until it
is disposed of.
Personnel All persons who carry out activities on and with the system are referred
to as personnel. Personnel can be, for example, the operator, the
cleaning staff, or the security staff. The personnel meet the personnel
qualifications required by the manufacturer.
Service technician Experts and specialists or representative authorized by the manufac-
turer to perform commissioning, maintenance and servicing.

3Description
12 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
3 Description
3.1 Graphical display
K3x K4x
Abbreviation Description Abbreviation Description
A Passage width B Floor ring height
G Passage height I Cladding height
J Total height Q Total diameter
T Exterior diameter U Interior diameter
3.1.1 Main mechanical components
Abbreviation Description
aDrum wall
Curved, fixed aluminum frame for supporting curved glass or panelling.
bDrum wall edge
Fixed structure made of vertical frame profiling for accommodating control units.
cRotation unit turnstile
Rotating inner part of the door.

Description 3
BAL_K32_K42_M_EN_1V1_REC_121-006454677 13 / 24
3.2 Description of the manual revolving door
The system consists of three or four turnstile wings. They can be operated manually by horizontally or
vertically mounted handles. The recommended direction of rotation is usually counterclockwise.
The turnstile can be locked individually by different locking systems. An optional night shield can be
mounted on the system.
The ceiling lighting is usually controlled by an on-site light switch or a building management system.
Depending on the equipment a speed control brake is integrated. If the rotation speed of the system
is too fast, caused by persons or wind, the speed control brake can be used to limit the speed to the
preset value.
3.3 Safety features
3.3.1 Safety strips on turnstile wings
On the turnstile wings there are rubber safety strips.
The safety strips serve as protection to reduce bruising, for example of hands, feet and heels.

4Options
14 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
4 Options
4.1 Lighting control
The lights can be turned on or off via an on-site light switch or over the building control centre.
4.2 Speed control
Dependent on the configuration an electronic or hydraulic speed control is installed in the drive unit
for safety reasons. This prevents the turnstile from spinning too fast when passing through the re-
volving door too quickly. The limitation of rotation speed can be adjusted on the speed control.
4.3 Foldable turnstile wings and/or foldable drum walls
The system can be equipped with hinged turnstiles and / or, in case of a three-wing system, with
hinged drum walls.
If a turnstile leaf and/or a drum wall is manually opened, this condition is signaled to the system con-
trol via a monitoring switch. At the same time, the turnstile movement is immediately stopped in all op-
erating modes and the system control is switched off.
To continue the set operating mode, all turnstile leaves and/or the drum walls must be manually re-
engaged in their original position.
The turnstile starts automatically and continues the set operating mode.
Folding turnstile leaves are held in position by electrical or mechanical leaf locks.
Folding drum walls are held in position by magnets.
Basic positions
Inside
K32 K42
Outside
Folding positions
Inside
K32 K42
Outside

Options 4
BAL_K32_K42_M_EN_1V1_REC_121-006454677 15 / 24
Folding drum walls only for K32
Inside
Outside
4.4 Turnstile lock mechanisms
4.4.1 Electromagnetic turnstile lock
Unlock the turnstile
Pull the knob
Turn the knob to the right until it stops and then re-
lease it.
Lock turnstile
Turn the knob to the left.
Let the knob go and it should retract.
Rotate the turnstile manually to the home position from
the outside of the door until you hear the locking pin en-
gage. Ensure that the turnstile can no longer be rotated
manually.
4.4.2 Electromagnetic turnstile lock (Fail Secure)
NOTICE
Fail Secure = Monostable locking, locked without current.
The system is equipped with a turnstile lock. In the operating mode LOCKED, the turnstile is automat-
ically locked in the home position and unlocked when another operating mode is selected.
If the power supply fails, the status LOCKED or UNLOCKED is maintained. If the turnstile is locked in
the event of a power failure, it can be unlocked by means of a manual unlocking device (bow handle).
Please note the following steps:

4Options
16 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
Unlocking the turnstile lock
– Pull the bow handle.
– Turn bow handle to the right until it reaches the stop
and release.
Reset turnstile lock
– Turn bow handle to the left.
– Release bow handle, the bow handle must retract
downwards.
4.4.3 Turnstile bar-bolt lock
The turnstile can be locked with a bar-bolt lock, integrated in the door frame profile. By rotating the
profile cylinder together with the ceiling construction, and/or additionally with a fitted socket integrated
in the floor.
4.4.4 Turnstile corner lock
The turnstile can be locked with a corner lock, at the bottom of the door frame profile. By rotating the
integrated profile cylinder with a fitted socked integrated in the floor.
4.5 Night shield variations
4.5.1 Manual night shield
Night shield with mechanical bar-bolt lock or hook bolt lock
The night shield can be locked and unlocked with profile cylinder locks integrated in the door frames.
If the night shield is in locked position, then it must be unlocked and completely pushed open manu-
ally.
Then the operating mode of the door can be selected.
4.5.2 Night shield - deadman
CAUTION
Night shield crushing danger
a) Fingers or hands getting crushed, sheared or pulled in
ðTo avoid crushing, the operator must have a clear view of the night shield during the OPENING
and CLOSING process.
NOTICE
If the night shield is manually locked (i.e. with a bar lock), then please ensure that the night
shield wings are manually unlocked before using the key reversing switch.
Switch example
It can be operated with the key reversing switch.
Opening process: the night shield is opened by turning the key reversing switch to the right
(see arrow direction) and holding the position. If the night shield is locked electrically, then it
will simultaneously unlock. The opening process will stop when the key reversing switch is
no longer being turned or held. The opening process will resume by turning the key to the
right again and holding the position.
Closing process: the night shield is closed by turning the key reversing switch to the left
and holding the position. The closing process will stop when the key reversing switch is no
longer being turned or held. If the night shield is locked electrically, then it will lock automat-
ically in the locked position.
Collision detection: if a night shield wing hits an obstacle during the opening or closing pro-
cess, the night shield will stop and remain stopped. The next opening or closing process will
start when the key reversing switch is turned and held in position again.

Specifications 5
BAL_K32_K42_M_EN_1V1_REC_121-006454677 17 / 24
5 Specifications
5.1 Environmental conditions
Temperature range From -15 to +50° C
Humidity range Up to 85% rel. humidity, not condensing
5.2 Electrical connection data (optional)
Illumination
Mains voltage: 230 VAC
Frequency: 50-60 Hz
Nominal power: max. 120 W
Mains fuse: 10A circuit breaker with tripping characteristic C or K
Control voltage: 12 VDC
Safety class: 1
Degree of protection: IP 20
Electrical night shield
Mains voltage: 230 VAC
Frequency: 50-60 Hz
Nominal power: max. 120 W
Mains fuse: 10A circuit breaker with tripping characteristic C or K
Control voltage: 24 VDC
Safety class: 1
Degree of protection: IP 20

6Servicing and maintenance
18 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
6 Servicing and maintenance
6.1 General remarks
According to current legislation, the operator of an automatic door system is responsible for its main-
tenance and safety.
Accidents or defects can be avoided if the system operator takes good care of the system.
Testing
Type of test Measure
Visual inspection Check door leaves, guides, bearings, limiting devices, sensors, and the securing of
crushing and shearing points for damage.
Mechanical inspection Check fastenings for tight fit.
Safety check (exit and es-
cape routes)
Check sensors, safety devices, and monitoring devices for tight fit and damage.
Function testing Check functioning of switches, operators, controllers, power or energy storage
devices, and sensors.
Also check the adjustment of the safety devices and the setting of all movement se-
quences including the end points.
Servicing
Type of servicing Measure
Adjusting and cleaning Clean and adjust bearings, sliding points, and power transmission.
For documentation and information purposes, the testing and servicing work as well as the condition
of the system are recorded in a test log book. The test log book must be kept for at least one year or
until the next testing/servicing.
IMPORTANT
The testing and/or servicing interval according to the manufacturer's specification is at least 1
to 2 times a year.
IMPORTANT
The recommended and planned spare parts and wearing parts can be requested from your
service center.
6.2 Monthly inspection work performed by the operator
The monthly tests and inspections of individual components by the operator require little time and
serve in particular to prevent accidents caused by improper handling of the system. Depending on the
equipment of the plant, we recommend that the following inspection work be carried out on a monthly
basis.
Test / Inspection Procedure Expected results
Visual inspection of all safety strips – Visually inspect all safety strips. – The safety strips can not have
any mechanical damage and they
must be installed correctly and
firmly over the entire length.
Door leaves / Side screens – Verify the state of the glazing.
– Verify the state of the seals / pro-
files.
– No glass damage.
– No seals torn off (energy loss).
– The door is the "visit card" of your
company. Take care that it is
maintained in a perfect condition.

Servicing and maintenance 6
BAL_K32_K42_M_EN_1V1_REC_121-006454677 19 / 24
CAUTION
Danger of people being trapped inside the turnstile.
a) Bruises and contusions through from the turnstile wing.
ðVisual inspection, check whether people are trapped inside.
Visual inspection of the instructions
and labeling (buttons / switches)
– Verify that all labels are present
and legible.
– All labels must be present, legible
and firmly applied.
Visual inspection of the floor covering – Verify the floor covering for pos-
sible tripping hazards, uneven-
ness, damages, and dirt accumu-
lation.
– The floor covering must be free
from tripping hazards, uneven-
ness, damages and dirt accumu-
lation.
CAUTION
Risk of burns, hot surfaces!
a) Risk of burning hands when replacing bulbs!
ðAllow bulb to cool at least 5 minutes before replacing and/ or wear protective gloves.
Visual inspection lighting – Verify whether the lights are in-
stalled correctly and turn them
on.
– Lights must be installed correct
and function.
Function test Night shield – Close and lock the night shield.
– Push to verify whether the night
shield is locked securely.
– The night shield is completely
closed and locked.
Operator casing – Check the attachment of the op-
erator casing.
– It must be completely closed and
must correctly engage into the
hinges.
Function test of the speed control
brake
– Rotate the turnstile faster than
normal speed until automatic
braking of the rotation occurs.
– The turnstile will be harder to
push.
– After reducing the rotation
speed, the turnstile should be
easier to push.
Function test of the turnstile lock,
for example bar bolt lock or corner
lock.
– Rotate the turnstile to the lock po-
sition.
– Engage the lock.
– Push to verify whether the turn-
stile is securely locked.
– The turnstile is securely locked.
Visual inspection of the glass label – Verify that the label is present. – The glass label must be firmly at-
tached at eye level.
6.3 Cleaning and care
DANGER
Warning: risk of fatal electric shock!
a) Risk of death by electric shock
ðDo not touch the drive system while the main power is connected.
ðDo not spray water into the drive system.

6Servicing and maintenance
20 / 24 BAL_K32_K42_M_EN_1V1_REC_121-006454677
NOTICE
If available, select the MANUAL operating mode before starting cleaning and additionally
press an emergency stop switch.
IMPORTANT
The system must be kept free of dirt, leaves, snow and ice!
a) In case of heavy soiling contact a professional.
b) The use of road salt or gravel in front of the access areas and inside the plant must be avoided.
c) It is recommended to impregnate the safety strips and sensors with a water-repellent care
product.
IMPORTANT
Any other cleaning agents not mentioned above must not be used!
What Interval Cleaning agent
General parts Weekly Damp cloth / neutral to slightly al-
kaline, aqueous wetting agent solu-
tion / vinegar diluted with water
Sensors / safety strips Weekly Plastics cleaner
Floor coverings Weekly Vacuum cleaner / carpet cleaner