REMKO ELT 10-HT User manual

Edition GB – J08
REMKO ELT 10-HT
High temperature
Electric heater
Operation · Technology · Spare parts

3
Contents
Carefully read this operating manual prior to commissioning/using
the units!
This operating manual is a translation of the German original.
This manual is an integral part of the unit and must always be kept in
the vicinity of the installation location or on the unit itself.
Subject to modifications; no liability accepted for errors or misprints!
Unit description 4
Safety notes 4
Commissioning 5-6
Shutdown 6
Operation with a warm air hose 6
Care and maintenance 6
Troubleshooting 7
Intended use 7
Customer service and guarantee 7
Environmental protection and recycling 7
Electrical wiring diagram 8
Maintenance protocol 9
Exploded view of the unit 10
Spare parts list 11
Technical data 11

4
REMKO ELT 10-HT
The units are portable electric
heating units for industrial
applications at various locations.
The units are operated exclusively
with electric power and have been
designed for high-temperature
applications with an air outlet
temperature of up to 120°C.
The air outlet temperature is
altered by manually adjusting the
fan speed.
The units can be operated using no
more than one high-temperature
hose (accessory) with a ø of
205 mm and a length of 7.6 m.
The units are equipped with
special-purpose, highly efficient
electrical heating coils for
immediate and consistent heat
generation, low-maintenance axial
fans, a safety thermostat, a room
thermostat socket and a mains
cable with earthed safety plug.
The units conform to the
fundamental health and safety
requirements of the appropriate
EU stipulations.
The units are dependable and offer
ease of operation.
The units may be used among
other things for the following:
■ Drying heat-resistant materials
■ Generating process heat for
industrial applications
■ Hardening plastics
■ Pest control
■ Drying out construction work/
heating
Safety notesUnit description
The units have been subjected
to extensive material, functional
and quality inspections prior to
delivery. However, dangers can
arise from the units if they are used
improperly or not as intended by
untrained personnel!
Please observe the following notes:
■ In the event of defects that
endanger the operational safety
of the unit, operation must be
discontinued immediately
■ Observe the respective local
electrical regulations and the
necessary safety measures when
using the units
■ Maintain safety distances to
combustible materials
0.5 m at the side of the unit and
on the air inlet side
2.0 m on the air outlet side
■ An unobstructed air inlet and air
outlet must be guaranteed at all
times
■ The units must not be covered
during operation
■ Never insert foreign objects into
the units
■ The units must not be operated
in the vicinity of bathtubs,
showers, swimming pools etc.
■ The units must not be operated
directly below a wall socket
■ The units may not be exposed to
direct jets of water
CAUTION
Extensions to the connection
cable must only be conducted
by authorised specialist
electricians, taking into
consideration the unit capacity,
cable length and local use.
■ The units must not be installed or
operated in potentially flammable
or explosive environments
■ The units must not be operated
in locations where:
Combustible gaseous, air or
dust-air mixtures could be
produced; flammable small parts
could be sucked in, set alight on
the heating coil and blown out
in a glowing state
■ Flooring and ceilings must be
fire retardant
■ The air inlet and outlet must not
be constricted
■ The relevant safety guidelines
of the Employer's Liability
Insurance Association or
property insurer must be
observed
■ The units must be installed
in a stable position and must
not topple over or slide out of
position during operation
■ The units must not be left
unattended during operation
■ The units must not be operated
in an environment with an
ambient temperature of over
60°C
■ All electrical cables for the
units must be protected against
damage, even damage caused
by animals

5
Commissioning
One person, who has been
adequately trained in the handling
of the units, should be tasked with
the operation and monitoring of the
units.
The units are equipped with
a 3-stage operating switch.
1. Move the operating
switch to the “0”
position.
2. Connect the unit's
power plug to a
properly installed
16 A mains socket.
Heating with a special
purpose HT room thermostat
or duct thermostat (accessories)
The units operate fully
automatically and according to the
air outlet/room temperature.
1. Pull out the strapping plug [2].
2. Connect the plug [3] of the
relevant thermostat to the
thermostat socket [1] on the
unit.
3
1
NOTE
The electrical connection for
the units must be made at
a separate feed point with
a residual current device in
accordance with VDE 0100,
Section 55.
3. Place the probe in a suitable
position according to the type
of thermostat used.
The thermostat probe must not
be located directly in the warm
air flow and must not be placed
directly on the cold floor.
4. On the room thermostat, set
the temperature required for
the application at hand.
5. Move the operating
switch to the “2”
(Heating) position.
GREEN indicator light on!
Heating without room
thermostat
The units are operating in
permanent operating mode.
1. Connect the supplied strapping
plug [2] to the thermostat
socket [1] on the unit.
2. Move the operating
switch to the “2”
(Heating) position.
GREEN indicator light on!
2
1
Adjust the air outlet
temperature
Upon start-up, set the fan speed to
the maximum setting.
If the YELLOW light does not
light up after an operating time of
approx. 5 minutes, please decrease
the fan speed by approx. 10%.
If the yellow light has still not lit
up after another 5 minutes, repeat
the previous procedure until the
YELLOW HT operating light is
continuously lit.
The unit has now been optimally
adapted to the ambient conditions
and is operating in high-
temperature mode at approx.
100-120°C.
Safety in the event of
excessive temperature
If the operating conditions change in
permanent operating mode and the
temperature at the air outlet exceeds
120°C, the unit reverts to a heating
capacity of 7 kW automatically.
The GREEN indicator light goes out,
the YELLOW one remains lit.
In this case, we recommend checking
the operating conditions or increasing
the speed by 10% until the max.
heating capacity is reactivated.
GREEN indicator light on!
In the event of serious heat build-up
caused by, for example, a constricted
air outlet, a lack of unrestricted air
intake or the fan being at a standstill,
the safety thermostat switches the
unit off. This needs to be manually
unlocked once the fault has been
rectified and the unit has cooled down.
Operating lights
1= HT mode YELLOW
2= max. heating capacity GREEN
3= STB fault RED
1 2 3

6
REMKO ELT 10-HT
Operation with
a warm air hose
The units are equipped
with a special-purpose high
performance axial fan.
This opens up the possibility of
operating the unit with an HT warm
air hose with a Ø of 205 mm and
a length of 7.6 m to transport the
heated air efficiently and effectively
to the place where it is required.
Only warm air hoses (accessories)
that have been approved by
Remko may be used as these have
been designed specifically for these
high temperature units.
Note about the assembly of the
warm air hose
■ Only special-purpose high-
temperature hoses may be used
■ Make sure that the unit’s outlet
nozzle is securely fastened
■ There should be no kinks or
bends in the hose lines in order
to prevent hot-spots forming
■ Make sure that the air outlet at
the end of the hose is clear at
all times
Regular care and observation
of some basic requirements will
ensure trouble-free operation and
a long service life of the units.
■ In accordance with the
operating conditions, the units
must, if necessary, be checked
at least yearly by a specialist
to ensure that they are in a
condition that is safe to use
■ Keep the units free of dust and
other debris
■ Only clean the units with a dry
or moistened cloth
■ Never subject to direct jets of
water.
e.g. pressure washers etc.
■ Never use abrasive or solvent-
based cleaners
■ Use only suitable cleaners, even
for heavy contamination
■ Check the inlet and outlet grille
for contamination on a regular
basis
■ Check the safety equipment
and protective devices on
a regular basis
■ Be careful not to damage
the temperature controllers’
probes or capillary tubes when
removing or mounting the
protective exhaust grid
Care and maintenance
1. Move the operating
switch to the “0”
position.
2. If the units are inactive for long
periods, disconnect them from
the mains power supply.
3. The supply air fan may run
on to cool the units and only
switch off after the cooling
down phase is complete.
4. If the units need to be stored,
clean them and, if necessary,
cover them with a plastic sheet/
film or cotton cloth and store
in a sheltered and dry storage
location.
Shutdown
Ventilation only operation
Only the supply air fan operates
in this setting. Thermostatic
regulation and heating operation
are not possible in this operating
mode.
Move the operating
switch to the “1”
position.
The fan speed can
likewise be changed
in this mode.
An electrical safety check must
be carried out in accordance
with VDE 0701 after any work
on the units.
CAUTION
!
Before undertaking any work
on the units, the power plug
must be removed from the
mains socket.
CAUTION
!

7
Troubleshooting Customer service and
guarantee
The units are designed exclusively
for heating and ventilation
purposes in industrial or
commercial use (not for living
space heating in private use) on
the basis of their structural design
and equipment.
The units must only be operated
by appropriately instructed
personnel.
With non-observance of the
manufacturer's specifications, the
respective local legal requirements
or after arbitrary alterations to the
units, the manufacturer shall not
be liable for resulting damages.
Intended use
As a prerequisite for any guarantee
claims to be considered, it is
essential that the ordering party
or its representative completes
and returns the “Certificate of
guarantee” to REMKO GmbH &
Co. KG at the time when the units
are purchased and commissioned.
The units were tested at the
factory several times to verify their
correct function.
However, if malfunctions should
arise that cannot be remedied by
the operator with the assistance of
the troubleshooting section, please
contact your specialist dealer or
contractual partner.
Disposal of packaging
When disposing of packaging
material, please consider our
environment.
Our units are carefully packed
and delivered in sturdy transport
packaging made from cardboard
and polystyrene.
The packaging materials are
environmentally-friendly and can
be recycled.
By recycling packaging materials,
you make a valuable contribution
to the reduction of waste and
conservation of raw materials.
Therefore, only dispose of
packaging material at appropriate
collection points.
The unit (fan) does not start.
1. Check the mains fuses on site.
2. Check the control fuse on the
rear panel of the unit.
3. Check the power plug.
4. Check the operating switch.
5. Check that the air circulating fan
can move freely.
The unit does not heat up.
1. Check the operating switch.
2. Check that the contactors are
functioning correctly.
3. Check that the temperature
controller is functioning correctly
and check the capillary tube for
damage.
4. Check whether the safety
thermostat has triggered or check
the capillary tube for damage.
5. Check that the thermostat and
the strapping plug are in place.
6. When operating the unit with
a room thermostat, set the
thermostat to a temperature
that is above the room
temperature.
If all of the functional checks
have been carried out without
any findings, please contact an
authorised service station.
NOTE
Adjustment and maintenance
work may only be carried out
by authorised and qualified
technicians.
NOTE
Operation other than the types
listed in this operating manual
is prohibited.
With non-observance, any
manufacturer liability or
guarantee claims are voided.
Environmental
protection and
recycling
Copyright
The redistribution, even in part,
or the use of this documentation
for purposes other than intended
is prohibited without the written
authorisation of REMKO GmbH &
Co. KG .
CAUTION
!
Safety devices
must not be bypassed or
disabled.
CAUTION
!

8
REMKO ELT 10-HT
Electrical wiring diagram
Legend:
C1 = Condenser
HW = Special-purpose heating insert
KL = Connection terminal strip
K1 = Contactor 1
K2 = Contactor 2
M = Fan motor
NK = Aftercooler thermostat
RT = Thermostat receptacle
S1 = Operating switch
STB = Safety thermostat
TH = Temperature controller
TL = Temperature controller
We reserve the right to modify the dimensions and design as part of the ongoing technical development process.
C1
H1
Grün
Black
X2:3
X2:4
KL:L1
4
1
4
2
TH
dT/120°C
CTL
dT/80°C
F1
6.3Amp
NN
N
H2
Gelb
N
H3
Rot
3
1
2
M
Braun
Blau
Blau
U2
U1
X2:2
1
4
2
STB
dT/100°C
Z
Braun
Fuse
13
14
X2:1
STB
100°C
HT-Betrieb
ab 80°C
Grünlicht an = 10,5 kW Power
ab 120°C Grünlicht aus = 7 kW Power
HW1
HW2
400V/3~N/50Hz
1 2 4 53
L1 L2 L3 N PE
7 kW 3,5 kW
EMV Filter
Poti 150kW
Leistungsregler
13 A2
A1
A2
A1
14
135
2 4 6 2 4 6
135
1 0 2
S1
2
1
1 2
A1
A2
A1
A2
12
NK
dT/37°C
5634
1 2
X3
X3
~
KL
K2K1
K2K1
K2
K1
RT
h
N
Betriebs-
stundenzähler
optional
Fuse
1 = Ventilation
2 = Heating
HT mode
from 80°C
Operating hours
counter
Power controller
EMC lter
Green light on = 10.5 kW power
From 120°C, green light o󰀨 = 7 kW power
optional
Yellow Red
Green
Blue
Blue
Brown
Black
Brown
6×2.5 mm2

9
Maintenance protocol ✍
Comments:.....................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
1. Date: .................
..............................
Signature
2. Date: .................
..............................
Signature
3. Date: .................
..............................
Signature
4. Date: ..............
..............................
Signature
5. Date: .................
..............................
Signature
6. Date: .................
..............................
Signature
7. Date: .................
..............................
Signature
8. Date: .................
..............................
Signature
9. Date: .................
..............................
Signature
10. Date:
.................
..............................
Signature
11. Date: .................
..............................
Signature
12. Date: ................
..............................
Signature
13. Date: ................
..............................
Signature
14. Date: ................
..............................
Signature
15. Date: ...............
..............................
Signature
16. Date: .................
..............................
Signature
17. Date: ................
..............................
Signature
18. Date: ................
..............................
Signature
19. Date: ................
..............................
Signature
20. Date: ...............
..............................
Signature
Unit to be maintained only by authorised specialists in accordance with the statutory regulations.
Unit type: .................................. Unit number: ...................................
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Unit cleaned - outside -
Unit cleaned - inside -
Fan blade cleaned
Protection grid cleaned
Safety equipment checked
Safety devices checked
Unit checked for damage
All fastening screws checked
Electrical safety check
Test run

10
REMKO ELT 10-HT
Exploded view of the unit
We reserve the right to modify the dimensions and design as part of the ongoing technical development process.
1
2
2
3 (3a)
4
36
6
57
15
13
11
33
14
2312
16
10
2019
18
8
35 9
24
25
26
27
29 28
30
31
32
22
21
17
34

11
Spare parts list
Technical data
1) Noise level measurement DIN 45635 - 01 - KL 3
Series ELT 10-HT
Nominal heat capacity kW 10.5
Switchable heating capacity kW Thermodynamic
Air volume m3/h 400-900
Air outlet temperature °C up to 120
Maximum ambient temperature °C 60
Power supply V/Hz 400/3~N / 50
Max. rated current A 15.9
Max. power consumption kW 11
Electrical protection (provided by the customer) A (slow) 16
Sound pressure level LpA 1m 1) dB (A) 70
Dimensions: Length mm 750
Width mm 305
Height mm 500
Weight kg 18.0
No. Designation EDP
21 Grommet for mains cable
EDP no. on
request
22 Fan with motor and protection
grid
23 Condenser
24 “RED” light (STB fault)
25 “GREEN” light (max. heating capacity)
26 “YELLOW” light (HT mode)
27 Thermostat receptacle assembly
28 6.3 A control fuse
29 Speed controller adjusting knob
30 Operating switch 1-0-2
31 Speed control film
32 Mains cable with plug
33 M012 speed control
34 Terminal block 6er (1.5 mm²)
35 Speed controller
36 Safety thermostat STB
Not
illustrated
Thermostat plug
Not
illustrated
Strapping plug
Not
illustrated
Operating hours counter
No. Designation EDP
1 Transport handle
EDP no. on
request
2 Reinforcement plate
3 Outer casing ELT 10-HT
3a Outer casing ELT 10-HT INOX
4 Front panel with outlet nozzle
5 Floor panel
6 Front plate of floor panel
7 Support plate, right
8 Heating insert assembly
9 Back wall
10 Support plate, left
11 Inner casing with outlet cone
12 Cover plate for STB
13 Mounting plate
14 Terminal block 6er (6 mm²)
15 Contactor
16 Aftercooler thermostat
17 Control thermostat with probe
18 Safety clamp for mains cable
19 EMC filter
20 Terminal block 5er (16mm²)
When ordering spare parts, please state the EDP no., unit number and type (see name plate)!

Consulting
Thanks to intensive training,
our consultants are always
completely up-to-date when
it comes to technical expertise.
This has given us the reputation
of being more than just
an excellent, reliable supplier:
REMKO, a partner who helps
to solve problems.
Sales
REMKO offers not just a well
established sales network both
nationally and internationally, but
also has exceptionally highly-
qualified sales specialists.
REMKO employees in the
field are more than just sales
people: above all, they must
be advisers to our customers
in air conditioning and heating
technology.
Customer service
Our units operate precisely and
reliably. However, in the event of
a malfunction REMKO customer
service is quickly on the scene. Our
extensive network of experienced
dealers guarantees quick and
reliable service.
REMKO INTERNATIONAL
... and also right in your neighbourhood!
Take advantage of our experience and advice
REMKO GmbH & Co. KG
Air conditioning and heating technology
Im Seelenkamp 12 D-32791 Lage
Postfach 1827 D-32777 Lage
Telephone [phone]
Fax [phone]
E-mail [email protected]
Internet www.remko.de
We reserve the right to make technical changes and provide no warranty as to the accuracy of this data!