ResMed AIRMINI User manual

User guide
User guide
English | 简体中文

ResMed.com/AirMiniApp

English 1
ENGLISH
Welcome
The AirMini™system combines ResMed’s AirMini self-adjusting
pressure machine, masks and the AirMini™ App (AirMini™ China App).
WARNING
Read this entire guide before using the machine.
Indications for use
Use with AirFit series masks and AirMini tubing and accessories. The
AirMini self-adjusting system is indicated for the treatment of
Obstructive Sleep Apnoea (OSA) in patients (female patients with mild
to moderate OSA when using AutoSet for Her treatment mode)
weighing more than 30 kg.
It is intended for home and hospital use.
Contraindications
Positive airway pressure therapy may be contraindicated in some
patients with the following pre-existing conditions:
•severe bullous lung disease
•pneumothorax
•pathologically low blood pressure
•dehydration
•cerebrospinal fluid leak, recent cranial surgery, or trauma.

2
Adverse effects
You should report unusual chest pain, severe headache, or increased
breathlessness to your prescribing physician. An acute upper respiratory
tract infection may require temporary discontinuation of treatment.
The following side effects may arise during the course of therapy with
the machine:
•drying of the nose, mouth, or throat
•nosebleed
•bloating
•ear or sinus discomfort
•eye irritation
•skin rashes.
At a glance
The AirMini system includes the following:
•AirMini: the AirMini machine, power supply unit, drawstring bag
and one of the following:
•AirMini setup pack - F20: AirMini tube, F20 connector for AirMini OR
•AirMini setup pack - N20: AirMini tube, N20 connector for AirMini,
HumidAirX™, HumidAirX Plus OR
•AirMini mask pack for P10: AirMini tube, AirFit™ P10 for AirMini
mask (M), P10 cushion (S), P10 cushion (L), HumidAirX, HumidAirX
Plus, AirFit P10 headgear clips.

English 3
Your AirMini system
Your AirMini system is comprised of the AirMini machine and one mask
pack or one setup pack.
A AirMini machine 6 20W power supply unit
B F20 connector for AirMini and AirMini
tube
7 F20 connector for AirMini
C N20 connector for AirMini and
AirMini tube
8 Vent
D AirFit P10 for AirMini and AirMini
tube
9 Vent module
1 Start/Stop button 10
Anti Asphyxia Valve (AAV)
2 Power inlet 11 N20 connector for AirMini
3 Air outlet 12 AirFit P10 for AirMini
4 Air filter cover 13 Heat moisture exchanger - HumidAirX
(blue) and HumidAirX Plus (gray)
5 Bluetooth®button 14 AirMini tube
Your machine is compatible with ResMed's F20 and N20 series masks
and with the AirFit P10 for AirMini. Make sure all parts and accessories
used with the machine are compatible. For compatibility information,
refer to www.resmed.com for more information.

4
Your AirMini machine is designed to work with ResMed’s AirMini app.
However, the AirMini app is not essential to operate the machine. For
more information on the AirMini app, refer to Using your machine with
the AirMini app or the AirMini app Patient eHelp.
HumidAirX and HumidAirX Plus
The HumidAirX and HumidAirX Plus are waterless humidifiers. These
are designed to provide more comfort by improving the moisture level
in the air you breathe and offering relief from possible dryness.
The HumidAirX is a good starting point for finding the right level of
humidification. The HumidAirX Plus will improve the humidity level
further and is useful when the ambient humidity level is very low (eg,
high altitudes, on an aircraft).
The HumidAirX and HumidAirX Plus can be used with the N20
connector for AirMini and AirFit P10 for AirMini only.
The HumidAirX and HumidAirX Plus must be replaced within 30 days of
opening the HumidAirX/HumidAirX Plus pack.
Setting up and starting therapy
Using your mask
Before you set up your machine, make sure you use a compatible mask.
For a full list of compatible masks for this device, see the Mask/Device
Compatibility List on www.resmed.com/downloads/masks. If you do
not have internet access, please contact your ResMed representative.
For information on fitting your mask, refer to the mask user guide.
Use your AirMini machine only as directed by your physician or
healthcare provider.

English 5
Set up your machine
1. Plug the power supply unit
into the machine and the
power outlet. The connector
has an angled edge so that
the power cord can only be
inserted into the machine
one way.
2. Connect the gray end of the
AirMini tubing firmly to the
air outlet.
Add optional humidification
(for N20 or AirFit P10 for
AirMini only)
To insert the HumidAirX or
HumidAirX Plus:
1. Open the connector by
gently twisting it.
2. Hold the
HumidAirX/HumidAirX Plus
at the sides, with the
colored side pointing down
and insert it.
3. Gently push together the
connector and twist until it
locks in place.

6
Connect your mask
1. Fit your mask as instructed in the mask user guide.
2. Attach the connector to your mask.
F20 Series N20 Series AirFit P10 for AirMini
Start therapy
1. Start therapy by pressing
the Start/Stop button or
breathe normally if
SmartStart™ is enabled.
Stop therapy
1. Remove your mask.
2. Press the Start/Stop button or wait until the machine stops if
SmartStop is activated.

English 7
Comfort features
Ramp Time, Pressure Relief and SmartStart are enabled on your
machine.
Ramp Time
Designed to make the beginning of therapy more comfortable, Ramp
Time is the period during which pressure gradually increases from a
lower start pressure to the prescribed treatment pressure.
Pressure Relief
When Pressure Relief is enabled and turned on, you may find it easier
to breathe out. This can help you get used to therapy.
Note: Pressure Relief must first be enabled by your provider.
SmartStart
When SmartStart is turned on, therapy starts automatically when you
breathe into your mask.
SmartStop
When SmartStop is turned on, therapy stops automatically after a few
seconds when you remove your mask.
Changing comfort features
Your AirMini machine has been set up for your needs by your provider,
but you may find that you want to make small adjustments to comfort
settings to make your therapy more comfortable.
For more information about comfort settings, or for information on
changing these settings, refer to the AirMini app Patient eHelp.

8
Using your machine with the AirMini app
Your AirMini machine can be used with ResMed’s AirMini app. Once
you have paired and connected your machine to your smart device via
Bluetooth, you can start and stop therapy, change comfort settings and
view your therapy data via the AirMini app. Data sent via Bluetooth is
encrypted to protect your privacy.
Connecting your machine and smart device
Before you start, ensure that the latest version of the AirMini app is
installed on your smart device. If not, download the app from the App
StoreSM.
1. Ensure your machine is set up correctly and plugged into a power
source.
2. On your smart device, enable Bluetooth.
3. Open the AirMini app.
The first time you open the AirMini app you will be asked to consent
to the use of cookies and to accept ResMed's Terms and Conditions
and Privacy Policy.
4. Check the boxes on the Welcome screen and then tap Continue.
5. On your machine, press the Bluetooth button when prompted
by the AirMini app.
When the light starts to flash blue , Bluetooth is enabled and your
machine is ready to connect.
6. On your smart device, tap Connect.
When your machine is discovered, the machine name appears in the
machine selection list.
7. Select the machine name from the list to connect.
8. The first time you pair your machine with your smart device, you will
need to perform the authentication procedure.
When prompted by the AirMini app, authenticate by entering the
four-digit key located on the back of your machine.