Rice Lake MSI-8000 User manual

MSI-8000
RF Remote Display
Operation Manual
PN 133063 Rev FAugust 11, 2020

An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Contents
© Rice Lake Weighing Systems ● All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3.1 Charging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3.2 Battery Longevity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Zero. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3 Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3.1 Tare and Display the Net Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3.2 Clear Tare and Revert to Gross Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.4 Zero and Tare in Multiple Load Cell Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.0 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Setup Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.1 Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.2 Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.3 Net/Gross . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.4 Peak Hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.5 Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.6 Hi-Res . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.7 Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3.8 Total Remote Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.4 Auto-Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.5 Setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6 Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7 Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.8 Remote Display Scale Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8.1 Filter Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8.2 Total Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Calibrating a Scale/Dyna-Link 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 Initial Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2.1 Routine Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2.2 C-Cal Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3.1 Standard Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.4 Reset the Load Cell Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

MSI-8000 RF Remote Display
ii Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
6.0 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1 Communications Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2 Communications Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2.1 Printer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2.2 RF Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.2.3 Setup Multiple Sensor Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2.4 Scan List ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.3 Communications Port Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.4 Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.4.1 Relay Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.5 Radio Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.1 802.15.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.2 Wi-Fi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.3 Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.4 FHSS (Frequency Hopper Spread Spectrum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.0 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.1 Error Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.2 Service Counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.3 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.4 Firmware Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.5 Reset the Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
The MSI-8000 RF Remote Display makes wireless control easy with the ability to operate weighing systems from a distance.
The wireless remote display can be used for viewing MSI ScaleCore-based crane scales and dynamometers, including any RF
compatible MSI-3460 Challenger 3, MSI-4260 Port-A-Weigh or MSI-7300 Dyna-Link 2.
It is fully sealed for outdoor use in most ambient conditions and enhances the safety and usability of Rice Lake’s Dyna-Link and
crane scale systems. The MSI-8000 RF Remote Display uses a rechargeable Lithium Polymer battery, providing up to 24 hours
(typical) of continuous use between charges.
This manual is intended for use by qualified technicians responsible for setting up and operating the MSI-8000 RF Remote
Display.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
1.1 Safety
Safety Signal Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not stand near the load being lifted as it is a potential falling hazard. Keep a safe distance.
Do not use for purposes other then weight taking or dynamic load monitoring.
Do not use any load bearing component that is worn beyond 5% of the original dimension.
Do not use any associated lifting product if any components of the load train are cracked, deformed, or show signs of fatigue.
Do not exceed the rated load limit of the associated Scale/Dynamometer unit, rigging elements, or the lifting structure.
Do not allow multi-point contact with the hook, shackle, or lifting eye of the associated Scale/Dynamometer unit.
Do not allow high torque on the Scale/Dynamometer unless it is specifically designed for high torque.
Do not make alterations or modifications to the unit or associated load bearing devices.
Do not remove or obscure warning labels.
For guidelines on the safe rigging and loading of overhead scales and dynamometers, read the "MSI Crane Scale Safety and
Periodic Maintenance Manual" (available at www.msiscales.com).
Keep hands, feet and loose clothing away from moving parts.
There are no user serviceable parts within the MSI-8000 RF Remote Display. Any repairs are to be performed by qualified service
personnel only.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING

MSI-8000 RF Remote Display
2 Visit our website www.RiceLake.com
1.2 Features
• Meets or exceeds all U.S./International safety and environmental standards
• No license required; Meets U.S./International RF Transmission Laws
• Rechargeable Lithium Polymer battery provides up to 24 hours operation when fully charged
• Automatic Power Off turns the unit off, after a user set time of no activity, to save battery life
• The enclosure is IP65 rated with shock cushioning on the corners
• Six, 1'' (25 mm) LCD digits for clear load readings
• Selectable for kg/lb/tons (US Short)/metric tons/kilonewtons
• Automatic or manual weight totalization for loading operations
• Eight setpoints can be set for in-range load/weight value for operator alerts or process control
• ScaleCore technology provides quick and easy firmware updates and calibration setup/backup
• Optional hard-wired link for applications where RF is not allowed
1.3 Options
Part No. Option Description
149549 Universal 115/230 VAC 50/60 Hz (NA plug standard) battery
charger for MSI-8000 RF Remote Display Battery charger with North American style plug
149550 Universal 115/230 VAC 50/60 Hz (EC plug standard) battery
charger for MSI-8000 RF Remote Display Battery charger with European style plug
150964 Cable Assembly Serial cable terminated with female DB-9 connector
151095 Audible Alarm Contact factory for further information
182223 12 V Car Charger Adapter for MSI-8000 RF Remote Display Battery charger for use in a 12 V vehicle
– RS-232 serial-output cable With D-9 connector 13' (4 m)
– Dual-purpose RS-232 serial communication and battery
charging cable assembly
13' (4 m) with charger pigtail;
Allows serial output while being powered with charger
– RS-232 serial-output cable 4 m TPU Jacket, unterminated 13' (4 m)
– RS-232 serial cable for hardwire connectivity 26' (8 m) connects 8000 to 7300 Dyna-Link
– RF Remote Modem, RS-232 For direct connection to computers, scoreboards or serial printers
– RF Remote Modem, RS-485 For direct connection to 485 serial devices
– RF Remote Modem, USB For direct connection to computers USB ports
– RF Remote Gateway For direct connection to an Ethernet LAN, use with MSI’s SCCMP program
– RF or Hardwired Scoreboard Display Various digit sizes from 1.2''–8'', contact MSI for models available
Table 1-1. Available Options

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 3
1.4 Front Panel
The MSI-8000 RF Remote Display front panel, keys and annunciators are described below
Figure 1-1. Front Panel
Key Functions
Annunciator Functions
Item No. Key Description
1The F1 key; Programmable to user selectable functions (Section 4.3 on page 9); Default = Off;
Functions as the Enter/Select key in the setup menus
2The F2 key; Programmable to user selectable functions (Section 4.3 on page 9); Default = Off;
Functions as the Scroll key in the setup menus
3
The F3 key; Pre-programmed to Print and cannot be changed
4
The Power key; Powers the unit on and off; In Setup mode, it returns the display to the Weigh mode without storing changes
5
The Zero key; Zeros the residual load on a scale; In Setup mode, it stores changes and returns to the prior level
6
The Tare key; Removes current load value and puts the system into Net Weight mode
Table 1-2. Key Functions
Item No. Annunciator Description
7 Center of Zero Indicates that the scale is within 1/4 d of zero
8 Standstill Indicates that the load has settled within the motion window (usually ± 1 d); When this is turned off, the scale will not zero, tare or totalize
9LED Functions Indicates the current displayed function
Example: If F1 blinks, the peak hold reading is captured. If F2 blinks, the Display and Function Test reading is captured.
10 Total Indicates the RF linked device is displaying the total accumulated weight; Displays only momentarily
Peak Indicates the RF linked device is in the Peak Hold mode
Net Indicates the RF linked device is in Net Load mode; A tare weight is subtracted from the gross load
Metric Ton In conjunction with the Ton annunciator, indicates the RF linked device is displaying metric tons
Ton Illuminated, indicates the RF Linked Device is displaying in U.S. Short Tons (1 ton = 2000 lb);
When illuminated with M the RF Linked Device is displaying in metric tons (1 metric ton = 1000 kg)
Kilonewtons Indicates load display is in kilonewtons
Kilograms Indicates load display is in kilograms
Pound Indicates load display is in pounds
11 Setpoints User programmable setpoints for overload warnings; Setpoints 1 and 2 are red high brightness LEDs
12 Multiple Sensors Number lit indicates the sensor being displayed; If more than one number is lit, sensors are being summed
Example: If both numbers 1 and 2 are lit, then the weight displayed equals the sum of sensor 1 and sensor 2.
13 Display Digits Include six 1'' (25 mm) sunlight visible LCD digits
14 Low Battery Indicates about 10% of battery life remains; Symbol flashes when automatic shutdown is eminent
Table 1-3. Annunciator Functions
1210
119
8
7
1
2
3
6
5
13
4
14
F1
F2
PRINT
F3
POWER
ZERO
TARE

MSI-8000 RF Remote Display
4 Visit our website www.RiceLake.com
2.0 Installation
This section provides an overview of the MSI-8000 RF Remote Display installation instructions.
2.1 Unpacking
When unpacking the MSI-8000 RF Remote Display, ensure all parts are accounted for and check for any visible damage.
If any parts were damaged in shipment, notify Rice Lake Weighing Systems and the shipper immediately. If the MSI-8000 RF
Remote Display must be returned, it must be properly packed with sufficient packing materials. When possible, retain the
original carton when shipping the unit back. A standard MSI-8000 RF Remote Display is shipped with a battery charger.
The charger is universal and will work on AC supplies from 100 VAC–240 VAC.
2.2 Getting Started
Fully charge the battery by plugging the charger into the charge port. Depending on the discharge level of the battery this can
take up to 6 hours.
The MSI-8000 RF Remote Display is often shipped pre-configured with a compatible sensor unit such as an Dyna-Link 2 or one
of the MSI crane scales. If the MSI-8000 RF Remote Display is purchased separately, or is to be used with a different system,
the RF transceivers will have to be paired (Section 4.4 on page 11).
Once RF setup is complete for the MSI-8000 RF Remote Display, the system will automatically connect with a scale/Dyna-Link.
It is recommended to do a site survey to identify operating range and usability of the RF Link. Position the scale/Dyna-Link at an
average operational height, and try the link at various positions and distances. The range may vary by the rotation of the scale/
Dyna-Link, as well as the site and installation variables.
2.3 Battery
Power to the MSI-8000 RF Remote Display is supplied by an internal rechargeable lithium polymer battery, which provides up
to 24 hours of continuous use between charging.
Figure 2-1. Battery Charger Plug-In
2.3.1 Charging
Each MSI-8000 RF Remote Display is shipped with a charged battery. However, before using the MSI-8000 RF Remote
Display, it is advised to charge the battery until the green light shows it is fully charged. When LOW BATT first displays, there is
approximately two hours of continued operation remaining. When LOW BATT starts flashing the batteries are nearly completely
drained. For maximum battery life, it is recommended to recharge the battery as soon as LOW BATT displays. It is safe to
charge the battery at any point in its discharge curve.
If the blue LED is on, the charger is in Fast Charge mode, which puts 80% of the charge into the battery within two hours and
can be used at this point. However, it is best to fully charge the battery, until the green light displays.
The charge connector is waterproof when connected and screwed in. To maintain IP65 rating, use the supplied plug cover
when the connector is not plugged in.
The AC end of the charger is not waterproof.
Note

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 5
Charger LED Modes
Blue light – Indicates a charge is in progress. Charging times vary from one hour to six hours depending on the
charge level of the battery when the charger is applied. If the charger is attached as soon as LOW BATT displays,
charge time will average three hours. It is OK to remove the battery charger while the blue light is on, but a
complete charge is recommended.
Green light – Indicates the battery is fully charged. The powered charger can be left connected to the MSI-8000
RF Remote Display continuously. It is recommended to leave the MSI-8000 RF Remote Display on the charger
when not in use.
Red light – Indicates a fault. Faults include over temperature, under temperature (the battery must be warmer
than 14°F (-10°C)), a severely depleted cell or charge time-out. When the charge times out a trickle charge is
applied to the battery. To clear a time-out fault, unplug the charger and then plug it back in. A severely discharged
cell may take days on the charger to recover.
2.3.2 Battery Longevity
The Lithium Polymer Single Cell Battery used in the MSI-8000 RF Remote Display has a rated number of charges of ≥ 300
before capacity starts to degrade. The charging life can be greatly increased by charging the battery more often, and not let it
reach the battery cutoff voltage of 3.0 V. The battery voltage can be seen by pressing a function key programmed as Test, the
battery must be replaced by an Rice Lake certified technician.
When the MSI-8000 RF Remote Display is not in use, it is recommended that the charger is left attached to keep
a charge.
The MSI-8000 RF Remote Display uses a small current when powered off which has the potential to deep
discharge the batteries. Never store the MSI-8000 RF Remote Display with a depleted battery. This can cause
permanent damage to the battery and require factory replacement. Shelf life of a fully charged battery is about
three months.
IMPORTANT

MSI-8000 RF Remote Display
6 Visit our website www.RiceLake.com
3.0 Operation
This section provides an overview of the MSI-8000 RF Remote Display operation instructions.
3.1 Power
Press to power the indicator On/Off.
Ensure the recommended power supply is secured prior to device operation (Section 2.3 on page 4).
3.2 Zero
Sets the zero reading of the scale to remove small deviations in zero when the unit is unloaded.
See Section 3.3 for zeroing (taring) a package, rigging or pallet weights.
Press . The weight must be stable within the motion window for the zero function to work.
When using multiple scales, ensure the scale to be zeroed displays.
The backup memory in the unit stores the tare reading, and can restore it even if power fails.
Zero works in Gross or Net mode.
Zeroing while in Net mode will zero the gross load causing the display to show a negative tare value.
The scale must be stable within the motion window and is lit before it will zero. The scale remembers the zero
request for two seconds. If a motion clears in that time, it will zero.
The scale will accept a zero setting over the full range of the scale. Zero settings above 4% of full scale will subtract
from the overall capacity of the scale.
Example: If 100 lb is zeroed on a 1000 lb scale/Dyna-Link, the overall capacity of the scale/Dyna-Link will reduce
to 900 lb plus the allowed over-range amount.
3.3 Tare
Tare is used to zero out a known weight such as rigging, a container or pallet and display the load in Net weight.
3.3.1 Tare and Display the Net Load
1. Load the item that needs to be tared onto the scale/Dyna-Link.
2. Press . The weight display changes to 0 and Net displays.
3.3.2 Clear Tare and Revert to Gross Load
Press . Net turns off indicating the unit is in Gross mode.
Only positive gross load readings can be tared.
Setting or changing the tare has no effect on the gross zero setting.
Taring will reduce the apparent over range of the scale.
Example: When taring 100 lb of rigging on a 1000 lb scale, the scale will overload at a net load of 900 lb
(1000-100) plus any additional allowed overload (usually about 4% or 9 d).
To view the gross load without clearing the tare value, set an F-key to Net/Gross (Section 4.3.3 on page 10).
POWER
Note
ZERO
Note
TARE
TARE
Note

Operation
© Rice Lake Weighing Systems ● All Rights Reserved 7
3.4 Zero and Tare in Multiple Load Cell Systems
The channel displayed is considered the Focus Channel. Pressing or only affects the displayed channel.
When displaying summed channels, ZERO or TARE commands are sent to all devices that contribute to the displayed weight.
Example: In Both mode, if pair 1 (sum of SC0 and SC1) displays, pressing zeros only SC0 and SC1.
If displaying the grand total using the ALL mode then pressing will zero all connected sensors.
Using the Tare function: If one device is tared in the individual Display mode, the summed weight will be the sum
of a Net and a Gross weight. If is pressed when displaying any of the summed modes, all devices that
add to the current display are tared and placed in Net mode.
ZERO
TARE
ZERO
ZERO
TARE

MSI-8000 RF Remote Display
8 Visit our website www.RiceLake.com
4.0 Setup
This section provides an overview of the MSI-8000 RF Remote Display setup instructions.
4.1 Setup Navigation
To navigate the menus during setup, follow the information below:
• Press to enter or select a parameter
• Press to scroll through the parameters
• To enter a decimal point, press while the digit is blinking
• Press to save and go back one level or to Weigh mode;  displays briefly
• If a wrong value is entered, press to step back one digit and press to change the digit
• Press to exit without saving changes
4.2 Setup Menu
To enter the setup menu, press and simultaneously.
Parameters Choices Description


–Function Key 1 – Configurable to listed parameters (Section 4.3 on page 9); Default 
Function Key 2 – Configurable to listed parameters (Section 4.3 on page 9); Default 
 No function is assigned; The F-key is disabled
 Test – Runs an LCD test (Section 4.3.1 on page 9)
 Total – Accumulates multiple weighments (Section 4.3.2 on page 9)
 View Total – Activates the total weight display followed by the number of samples (Section 4.3.2 on page 9)
 Net/Gross – Toggles between Net and Gross modes (Section 4.3.3 on page 10)
 Peak Hold – Automatically updates display when a higher peak weight reading is established (Section 4.3.4 on page 10)
 2 Units – Switches the force units between lb and kg (Section 4.3.5 on page 10)
 5 Units – Scrolls through all available units: lb, kg, Tons (US Short), metric tons and kilonewtons (Section 4.3.5 on page 10)
 Hi Res – The unit is more sensitive to motion and movement resulting in a less stable display (Section 4.3.6 on page 10)
 Print – Outputs a configured text string to the RS-232 port on the base of the Dyna-Link (Section 4.3.7 on page 11)
 Tare – Not used, MSI-8000 RF Remote Display has a dedicated Tare key
 Scan – Displays RF connected channels in order
 Total Remote Devices – Displays the summed weight of RF connected sensors (Section 4.3.8 on page 11)






Auto Off – Prolongs battery life of the scale by turning power off after the set time (in minutes) that the scale is not in use
(Section 4.4 on page 11)


 Greater Than – Setpoint triggers when the tension exceeds the value
 Less Than – Setpoint triggers when the tension is less than the value
 Off - Setpoint parameter is disabled
 
 Battery Life – Sets the options for standard or extended battery life (Section 4.6 on page 13)





Standards – Sets the industry standard to be used
Table 4-1. Setup Menu Parameter Descriptions
F1
F2
POWER
ZERO
ZERO
F2
POWER
PRINT
F3
ZERO

Setup
© Rice Lake Weighing Systems ● All Rights Reserved 9
4.3 Function Keys
There are two programmable function keys on the MSI-8000 RF Remote Display, and .
• Function key setup is independent of the connected scale function keys
• and are standard on the MSI-8000 RF Remote Display and do not need to be programmed
• If a function key does not work, the connected scale may not be set up to support the key
Example: If F-key is set for Total, then Total mode setup in the Setup menu must also be set up for target scale.
To set a function key use the following steps:
1. Press and simultaneously.  displays.
2. Press to scroll to the function key to be programmed.
3. Press . The currently saved parameter displays.
4. Press to scroll through the choices.
5. Press to select the desired choice.
6. Press to save and exit.
4.3.1 Test
The test feature only tests the MSI-8000 RF Remote Display. Set an F-key to TEST.
To run a test, press Fx-TEST, the following items scroll across the display.
• Light all LCD segments and the LEDs
• followed by the version number
• followed by the battery level in volts
• followed by counting from 00000–99999
The test can be single stepped by:
1. Press Fx-TEST, immediately press to stop the auto scroll.
2. Use to scroll through the steps and to view the step value.
3. Press to abort the test at any time.
Internal tests are also performed, if any test fails, an error code displays. See Section 7.1 on page 31 for a description of all
error codes.
4.3.2 Total
1. Ensure the Total mode has been programmed in the setup menu. If this has not been setup the F-Key assigned to
Total will not work.
2. Program an F-key to Total (Section 4.3).
3. Press Fx-Total to perform the total function that was set in Section 4.8.2 on page 15.
F1
F2
TARE PRINT
F3
PRINT
F3
ZERO
F2
F1
F2
F1
ZERO
F2
F2
F1
ZERO

MSI-8000 RF Remote Display
10 Visit our website www.RiceLake.com
4.3.3 Net/Gross
Program an F-key to NetGross (Section 4.3 on page 9).
Press Fx-NetGross to toggle between gross and net (gross minus tare). Fx-NetGross only functions if a tare has been
established.
The operator can switch back to gross from net without clearing the tare value. Only clearing or setting a new tare will change
the tare value held before switching into Gross Mode.
4.3.4 Peak Hold
Peak Hold uses a high speed mode of the A/D converter allowing it to capture transient loads at a far higher rate than typical
dynameters.
• Peak Hold is cleared and enabled by pressing Fx-P-HLd
• When a new peak is detected, the Fx LED flashes three times
• The accuracy of the system in peak hold is slightly reduced to 0.2% of capacity + 5d
• The filter setting is turned off while in Peak Hold mode to ensure the fastest acquisition rate
Example: The Peak Hold function is useful in Dynamic and Fall tests. Common tests include Overall Breaking
Strain (OB€), Breaking Force, and Cycled Breaking Strain.
Capture Peak Force:
1. Program an F-key to P-HLd (Section 4.3 on page 9).
2. Prepare the stand test and test sample.
3. Press .
4. Press Fx-P-HLd, confirm that Pk is lit on the display.
A small jump in the reading may occur depending on the stability of the test device.
5. Apply the test weight. The Fx LED will blink three times when a new peak ID is detected.
6. Remove the weight and the peak value is recorded.
7. To run a new test, press Fx-P-HLd to clear the peak value. Repeat Step 3–Step 6.
4.3.5 Units
Program an F-key to Unit (Section 4.3 on page 9).
Press Fx-Unit to set the units parameter to units required for display.
4.3.6 Hi-Res
Only available with the MSI-7300 Dyna-Link (refer to the Dyna-Link manual PN 152160)
When set to on, the filter is automatically set to the Hi-1 setting (if Hi-2 is already set, then the filter is not changed).
This will have a small effect on settling time. When set to off, the filter setting resets to the previous filter setting.
Program an F-key to HiRes (Section 4.3 on page 9).
Pressing Fx-HiRes places the display into a temporary High Resolution mode. This mode continues until Fx-HiRes is pressed
again, or power is cycled. In the Hi-Res mode the appropriate Fx LED blinks continuously at a slow rate.
Hi-Res mode does not increase the accuracy, but allows for smaller weight incrementation to display.
Use or to zero out any initial error.
ZERO
Note
Note
Note
TARE
ZERO

Setup
© Rice Lake Weighing Systems ● All Rights Reserved 11
4.3.7 Print
The Print function is set to , so there is no need to program or to Print.
Pushing or on the scale will cause the comm port on the MSI-8000 RF Remote Display to output the selected
data string (Section 6.2.1 on page 20).
If an F-key is programmed as Print and if Print Setup is configured as continuous, then is used for Start Print/Stop Print.
4.3.8 Total Remote Devices
Sensor summing must be enabled in the communications setup menu. If the Pairs or Both modes are enabled in the
communications setup menu, then pressing Fx-ttl.rd will scroll through the available combinations.
It is common to program for Scan and for  (Total Remote Devices) to allow quick switching
between individual channel displays (with Scan) or the summed weight (with
 ).
4.4 Auto-Off
The Auto-Off feature prolongs the battery life by powering off the unit when not in use. When a key is pressed or the detected
load is in motion exceeding 10 d, the time limit is reset.
When disabled, the unit will only turn off by pressing , or the battery dies.
To set the Auto-Off function:
1. Press and simultaneously.  displays.
2. Press to scroll to .
3. Press . The current auto off time displays.
4. Press to scroll through the available times.
5. Press when the desired time displays.  displays.
6. Press to exit setup and store the settings.
PRINT
F3
F1
F2
F1
F2
PRINT
F3
Note
F1
F2
POWER
PRINT
F3
ZERO
F2
F1
F2
F1
ZERO

MSI-8000 RF Remote Display
12 Visit our website www.RiceLake.com
4.5 Setpoints
The MSI-8000 RF Remote Display supports eight setpoints. Common uses of setpoints are for warnings or process control.
The front panel comes standard with two LED outputs for when setpoints 1 and 2 are triggered.
Figure 4-1. Setpoint LEDs
The MSI-8000 RF Remote Display can have an audible output option installed which is triggered by setpoint 1.
Contact Rice Lake Weighing Systems for other setpoint output options.
To set the setpoint:
1. Press and simultaneously.  displays.
2. Press to scroll to the desired setpoint ().
3. Press . The current setpoint mode displays.
4. Press to scroll to the setpoint mode desired.
5. Press . The current setpoint weight type displays.
6. Press to scroll to the desired weight type.
7. Press . The desired weight type continues to display.
8. Press .  displays.
9. Press to toggle between  and .
10. With the desired setting displayed, press . The current weight type value displays.
11. Press to scroll the numbers and to enter each digit.
Setpoint Description
Setpoint Mode
 Setpoint is not activated
 Indicates the setpoint will trigger when the weight exceeds a set value
 Indicates the setpoint will trigger when the weight is less than a set value
Setpoint Weight Type
 Responds to net or gross weight
 Responds to gross weight regardless of the display
 Responds to the totaled weight
 Responds to the total count (number of samples)
 Responds to the number of times the weight has exceeded 25% of capacity
Table 4-2. Available Setpoint Settings
PRINT
F3
ZERO
F2
F1
F2
F1
F2
F1
F1
F2
F1
F2
F1

Setup
© Rice Lake Weighing Systems ● All Rights Reserved 13
12. When the correct value displays, press . The next setup menu item is displays.
To enter a decimal point, press while the digit is blinking. To correct a digit, press to step back.
13. Press to exit Setup and store the settings.
4.6 Battery Life
Select either  (Standard Battery Life) or  (Long Battery Life).
In the Long Battery Life mode, the system is placed into a sleep state for several seconds at a time if there is no change in
tension. This disables the display in order to reduce power consumption and increase battery life. After several seconds, the
MSI-8000 RF Remote Display wakes up to check for any changes in tension. If there is a change in tension, the unit stays
awake. The unit remains awake if it is in configuration mode.
Although Long Battery Life mode can significantly increase battery life, performance is better in Standard Battery
Life mode.
1. Press and simultaneously.  displays.
2. Press to scroll to .
3. Press . The currently saved battery life displays.
4. Press to toggle between the choices.
5. With choice displayed, press to select.  displays.
6. Press to save and exit to Weighing mode.
4.7 Standard
Use the following steps to set up standard settings.
1. Press and simultaneously.  displays.
2. Press to scroll to .
3. Press . The currently saved standard displays.
4. Press to scroll through the choices.
5. With choice displayed, press to select.  displays.
6. Press to save and exit to Weighing mode.
Selection Description
 (Industrial) This is the most common setting for the MSI-8000 RF Remote Display; With the Industrial standard, there is full range zero,
access to units switching, filters, and peak hold
 (Handbook 44) Enables only approved features per the NTEP HB-44 rules and regulations; Access is denied to Peak Hold, and the zero range
may be limited; Filter menu is moved to the Calibration Setup menu, so filters are only accessible through the calibration seal
 (R-76)
Sets the scale to enable only approved features per OIML R-76; Only kg weight units are available; The zero range is limited to
4% (-1 to +3% relative to calibrate zero); Net/Gross function is temporary; Once net weight is established, pushing an F-key set
for Net/Gross will cause a maximum 5 second display of the gross weight; Clear the Tare to display gross weight constantly;
Other metrological aspects are changed to meet R-76 requirements
 (1Unit)
The 1Unit standard is exactly the same as Industrial, except units switching is inhibited; Used for metric only countries or where
1Unit standard is to allow the scale to be calibrated in units other than lb or kg, since conversions are eliminated;
Contact Rice Lake for more information on the standards settings
Table 4-3. Standard Menu Selections
F1
Note
POWER
ZERO
ZERO
Note
PRINT
F3
ZERO
F2
F1
F2
F1
ZERO
PRINT
F3
ZERO
F2
F1
F2
F1
ZERO

MSI-8000 RF Remote Display
14 Visit our website www.RiceLake.com
4.8 Remote Display Scale Setup
The MSI-8000 RF Remote Display can be used to operate several MSI crane scales (MSI-4260, MSI-3460 and MSI-7300).
Some functions can also be set using the MSI-8000 RF Remote Display. The information in this section pertains to the setup of
the scale being used with the remote. The scale displayed is the scale being remote configured.
4.8.1 Filter Setup
The filter settings are used to stabilize the weight in an unstable condition. Increasing the filter will improve the stability, however
settling times will be longer. The MSI-8000 RF Remote Display employs algorithms that speed up large weight changes while
still controlling vibration with high filter settings.
Use the following steps to set up filtering.
1. Press and simultaneously.  displays.
2. Press to scroll to .
3. Press . The currently saved Total mode displays.
4. Press to scroll through the choices.
5. With choice displayed, press to select.  displays.
6. Press to save and exit to Weighing mode.
Parameters Choices Description





Weight Filter – Allows the scale to adjust to situations where there may be movement;
See Section 4.8.2 on page 15
Hi-2 – MSI-7300 only

 Total Accumulation – Sets the choice for weight accumulation for a single scale (Section 4.3.2 on page 9);
When set to off, it’s disabled
 Total On – Is a manual choice for accumulation (Section 4.3.2 on page 9)



Auto Total – Choices for setting automatic accumulations

 Greater Than – Setpoint triggers when the tension exceeds the value (Section 4.5 on page 12)
 Less Than – Setpoint triggers when the tension is less than the value (Section 4.5 on page 12)
 Off – Setpoint parameter is disabled (Section 4.5 on page 12)
 

Battery Life – Sets the options for standard or extended battery life;
See Section 4.6 on page 13
Table 4-4. Settings for the Scale Using the Remote
PRINT
F3
ZERO
F2
F1
F2
F1
ZERO

Setup
© Rice Lake Weighing Systems ● All Rights Reserved 15
4.8.2 Total Mode
For the accumulation of multiple weighments, the Total function uses the displayed load, so gross and net readings can be
added into the same total.
There are four modes of totalizing, a manual and three auto modes: , , .
All modes require that the weight on the scale return below 0.5% (relative to full scale) of Gross Zero or Net Zero before the
next weighment can be added. Applied weight must be ≥1% of full scale above Gross Zero or Net Zero before it can be
totaled.
Manual Total
Manual Total () adds a current weight to a previously accumulated value manually. To add weight to the total it must be
greater than 1% of capacity and not yet totaled. This assures that a weight on the scale is only added to the total once.
1. Program a F-key to  (Section 4.3 on page 9).
2. With the weight to be added on the scale, press F-Total. The acknowledge LED blinks to indicate the weight was
accepted and the TOTAL annunciator lights. Then the total weight displays for five seconds and the number of
samples displays for two seconds.
3. Repeat Step 1 and Step 2 until all weight samples have been added.
Total mode will not function while the scale is in motion, ensure is on. If the system fails to achieve stable
readings, increase the filter setting or increase the size of the scale division (d) in the Init Cal procedure.
The F-Total functions as View Total only until the 1% threshold is exceeded to allow the addition to the total value.
Auto Total
This mode has three variations which are programmed in the Setup menu.
Program an F-key to AUTO TOTAL, it functions as Auto Total On / Auto Total Off (Section 4.3 on page 9).
Set Total Mode
1. Press and simultaneously.  displays.
2. Press to scroll to .
3. Press . The currently saved filter mode displays.
4. Press to scroll through the choices.
5. With choice displayed, press to select.  will be displayed.
6. Press to exit setup and store the settings.
Reset Total Load
To reset the total load to zero, press Fx-Total again and while the total load is being displayed, quickly press .
Setpoint Description
 (Auto Load) Ensures any settled load above the Rise Above threshold will be automatically totaled;
The scale must fall below the Drop Below threshold before the next total is allowed
 (Auto Last) Takes the last settled weight to auto total with; The total occurs only once the scale goes below the threshold;
Allows the load to be adjusted without a total occurring; Once the load is removed, the scale uses the last settled reading for total
 (Auto High) Uses the highest settled reading; This is useful for loads that can’t be removed all at once
Table 4-5. Auto Load Selections
Note
PRINT
F3
ZERO
F2
F1
F2
F1
ZERO
ZERO

MSI-8000 RF Remote Display
16 Visit our website www.RiceLake.com
5.0 Calibration
This section provides an overview of the MSI-8000 RF Remote Display calibration instructions.
5.1 Calibrating a Scale/Dyna-Link 2
The MSI-8000 RF Remote Display can be used for calibrating MSI ScaleCore-based crane scales and dynamometers,
including MSI-3460 Challenger 3, MSI-4260 Port-A-Weigh or MSI-7300 Dyna-Link 2.
They can be calibrated using standard precision test weights. It is required that the weight used is at least 10% of full capacity
in order to achieve rated accuracy.
When adequate test weights are not available, the scale/dynalink can be calibrated using a constant calibration
() (Section 5.2.2 on page 18).
If the linked scale/Dyna-Link is sealed for NTEP approval, the seal will need to be broken and the calibration switch
on the linked scale/Dyna-Link will need to be pressed for the MSI-8000 RF Remote Display to perform the calibration.
5.2 Initial Calibration
Initial calibration is used to setup units, capacity and resolution (d) required for the load cell.
Initial calibration is also performed after a calibration reset which deletes all calibration.
1. Press and simultaneously.  displays.
2. Press the programmed F-key to scroll to the load cell to be calibrated.
3. Press ,  displays.
4. Press . The default units are displayed.
5. Press to scroll through the available units.
6. With desired unit displayed, press to select.  displays.
7. Press . The default capacity displays.
8. To enter a different capacity, press .
9. Press to scroll through numbers and to save the selected numbers.
10. When all numbers have been selected, press to store the number.  displays.
11. Press . The default display divisions are displayed.
12. Press to scroll through the available display divisions.
13. With desired display division displayed, press to select.  displays.
14. Proceed with the routine calibration, starting with Step 2 of Section 5.2.1 on page 17.
Note
ZERO
F2
F1
F1
F2
F1
F1
F2
F2
F1
F1
F1
F2
F1