Ricoh Beluga-C1 Installation guide

Beluga-C1/C1.5 Training
1
Slide 1
D046/D049/D154/D155
COPIER TRAINING
Introduction
No additional notes

Beluga-C1/C1.5 Training
2
Slide 2
Introduction
This is a digital black-and-white wide-format
machine with 600 dpi resolution for scanning and
printing.
The controller is a GW controller. A Ratio
controller is also available for the D046/D049
only.
This is a combined training course for the
D046/D049 (BE-C1.0) and D154/D155 (BE-C1.5)
machines.
(The D154/D155 machines are minor upgrades to the
D154/D155.)
PREPARATION CHECK LIST
Provide the relevant manuals and any additional handouts you feel are
necessary. Special tools are listed in the parts catalog.
Description Quantity Remarks
Service Manual 1 per trainee Give copies to the trainees
Operation Manual 1 per trainee Give copies to the trainees
Training Schedule 1 per trainee Give copies to the trainees
Instructor’s guide and presentation 1 set Instructor only
Training machines 1 for every 3
trainees Have the trainees completely install these
during class.
Special Tools 1 set per
machine As necessary

Beluga-C1/C1.5 Training
3
Slide 3
Objectives
Install the machine and its peripherals in the
field.
Understand and perform routine maintenance.
Understand the PM table.
Understand the important SP codes.
Troubleshoot and repair this product in the field.
ORIENTATION
Provide the trainees with information about the training course procedures,
facilities, objectives and rules.
Introduction of instructors
Introduce yourself to the class, and any other instructors who will be taking part.
Tell them who to talk to if they have any problems.
Introduction of trainees
Distribute a list of those attending the course.
Try to generate a friendly and relaxed atmosphere, and encourage the class to
get to know each other.
If it will help, have the trainees introduce themselves (name, company, work
experience).
Explanation of curriculum
Pass out copies of the training schedule
Impress the importance of getting to the class on time
Go over the course objectives (key points listed on the slide).
Explanation of training center rules
Explain the general rules of your training center (smoking, breaks, use of
facilities, etc.)
Explain the tools and equipment available at the facility.
Impress on the trainees that they should not touch the machines until the
instructor says so, and that they are responsible for replacing tools and keeping
the classroom in order.

Beluga-C1/C1.5 Training
4
Slide 4
D046/D049/D154/D155
COPIER TRAINING
Course Overview
No additional notes

Beluga-C1/C1.5 Training
5
Slide 5
Course Overview
Product Outline
Specifications
Installation
Machine Overview
Scanning
Processes Around the Drum
Exposure
PRODUCT OUTLINE
The model will be introduced.
The optional peripherals will be introduced.
The product concept, sales points, and targets will be presented.
SPECIFICATIONS
The main specifications will be given. Significant items will be stressed.
INSTALLATION
Installation of the machine and the peripherals will be covered.
Firmware upgrade will be covered.
MACHINE OVERVIEW
The components will be discussed briefly.
The copy process will be outlined.
The machine’s organization and overall PCB structure will also be covered.
SCANNING
The scanner mechanism and sensors will be described.
The optional document feeders will be dealt with in a later section.
PROCESSES AROUND THE DRUM
Drum drive, charge, drum cleaning, quenching, and other processes around the
drum will be described
EXPOSURE
The latent image writing mechanism will be described.
This machine uses LED arrays.

Beluga-C1/C1.5 Training
6
Slide 6
Course Overview
Development and Toner Supply
Paper Feed and Cutting
Image Transfer, Paper Separation, and Paper
Transport
Fusing
Paper Exit
Maintenance
Optional Paper Cassette
DEVELOPMENT AND TONER SUPPLY
The development process will be described.
Toner supply mechanisms and toner density control will also be described.
Toner end detection will also be described.
PAPER FEED AND CUTTING
The paper feed mechanisms for the main body will be described.
The cutter will also be described.
The optional feed unit mechanisms are the same as for the main body, so do not
require a separate section.
IMAGE TRANSFER, PAPER SEPARATION, AND PAPER TRANSPORT
Image transfer and paper separation mechanisms will be described.
Transport from the drum to the fusing unit will be explained.
FUSING
Fusing will be described.
PAPER EXIT
The paper feed out mechanisms will be described.
MAINTENANCE
PM is described briefly.
OPTIONAL PAPER CASSETTE
This describes the optional paper cassette mechanisms.
OPTIONAL FOLDER
This describes the mechanisms in the optional fan folder and cross folder.

Beluga-C1/C1.5 Training
7
Slide 7
D046/D049/D154/D155
COPIER TRAINING
Product Outline
PURPOSE OF THIS SECTION
The model will be introduced.
The optional peripherals will be introduced.
The product concept, sales points, and targets will be presented.

Beluga-C1/C1.5 Training
8
Slide 8
How many models?
D046: Beluga-C1a
D049: Beluga-C1b
D154: Beluga-C1.5a
D155: Beluga-C1.5b
Differences
Maximum scan length
» D046/D154: 15 m (590”)
» D049/D155: 30 m (1180”)
Copy speed
» D046/D154: 120mm/s, 10 cpm (A1/D LEF), 5 cpm (A0/E LEF)
» D049/D155: 170mm/s, 14 cpm (A1/D LEF), 7 cpm (A0/E LEF)
Fusing lamps and hot roller are different
No additional notes

Beluga-C1/C1.5 Training
9
Slide 9
What is new with the D154/D155?
New functions
New counter specification (Available as a cost recovery
application)
- Additional count of large format sizes
- Length and area count logging
Scan to USB memory/SD card
(using USB2.0/SD Slot Type I)
"Scan to Color Print" (using PrintCopy Tool)
The security (Data overwrite security unit) and encryption
(HDD encryption unit) unit are pre-installed in the
D154/D155.
Newly developed options/peripherals
USB2.0/SD Slot Type I
PrintCopy Tool
"Scan to Color" requires a color capable printer that can be accessed via
network.
The D046/D049 machines continue to use these options:
¾Data Overwrite Security Unit Type H
¾HDD Encryption Unit Type A

Beluga-C1/C1.5 Training
10
Slide 10
Discontinued Options
The following peripherals were not launched.
Bridge Unit BU6500 (D407)
Folder FD6500A (B889)
Manual Feeder (D333)
Folder FD6500B (Cross Folder) (B890)
(These units were listed in the first version of this
training course but were cancelled prior to product
launch.)
No additional notes.