Rielta PYRONE-5 User manual

Installation Guide
1 Introduction
Passive infrared detector «Pyrone-5» (hereinafter, the Detector) is
intended for detecting intrusion into a closed protected space and
generating an alarm message by the relay contacts opening.
The Detector is resistant to the ambient light impact and radio
interference.
The Detector ensures absence of false alarms cased by movement
of pets with weight up to 40 kg if the Detector is installed at the height
not less than 2,3 m.
The Detector is installed directly on a wall or in a corner of a room.
2 Features of the Detector
- Dual-element pyrodetector;
- Spherical lens provides pet immunity as well as absence of
distortions within the detection zone;
- Protection against ingress of insects to the pyrodetector;
- Microprocessor-based signal processing;
- LED indicator mode selection;
- Selection of the detection range and pet immunity (10, 20 or
40 kg pet weight);
- The Detector is powered from power supply unit with rated output
voltage 12 V.
3 Specifications
Table 1
Parameter Value
Maximum detection range not less than 10 m
Recommended installation height 2,3 m
Power supply, V DC 8 V… 30 V
Consumed current, not more 15 mA
Output relay contacts
Energized FormA (NC) relay 30mA,
72 V
Alarm message duration, not less than 2 s
Detection zones (DZ) 8 far zones, 4 nearby
Pet immunity
Is chosen by means of «1» and «2»
DIP-switches in accordance with
Table 3
Ambient class
Boreal Climate (background
temperature 15 - 35 °С, relative
humidity 25 - 75 %, air-pressure
86-106 kPa)
Operating temperature from minus 30 °C to +50 °C
IP rating IP41
Dimensions, not more than 105х75х56 mm
Weight, not more than 100 g
Average service life, not less than 8 years
The Detector is designed to operate continuously around the clock.
The Detector interference protection provides absence of false
alarms under the following conditions:
- pets movement (in accordance with Table 3);
- background illumination differential;
- convective air flows;
- slow background temperature changing;
- voltage impulses in power-supply circuit;
- electrostatic discharge;
- electromagnetic fields in FM band.
The Detector generates Alarm message under human movement
within the detection zone limits transversally its side border at a speed
range 0.3 – 3 m/s for the distance of 3 m. The Detector is resistant to:
а) transport jolting with the acceleration 30 m/sec2 with impact fre-
quency from 10 to 120 impacts/sec or 15000 impacts with the same
acceleration;
b) the ambient temperature minus 50 … +50 °С;
c) relative air humidity (95 ± 3) % at the ambient temperature +35 °С.
After transportation under the conditions different to exploitation
conditions the Detector shall be ready to operate after a maximum
of six hours.
Average time between failures is not less than 60 000 hours.
Figure 1
8 Installation
Before installing the Detector, remove its cover and the PCB. For
this purpose:
- remove the cover of the Detector;
- push up the holder and remove the printed circuit board (PCB)
(See Figure 2);
- drill the holes (Figure 2) in the base of the Detector case. They will
be used for wire installation and fastening the Detector.
- choose the installation place, mark out and drill the installation holes
in the wall with regard for the position of the holes on the Detector base;
4 Scope of Delivery
Each Detector unit package contains the items listed in Table 2.
Table 2
Name QNT
Passive infrared detector «Pyrone-5»
Passive infrared detector «Pyrone-5». Installation Guide
1 pc.
1 copy
5 Field of Application
The Detector can be installed in apartments, as well as in shops,
offices, museums and industrial facilities. The Detector may be installed
in premises, that are inhabited by pets weighing up to 40 kg.
6 Choosing an Installation Place
When choosing the Detector installation place, it is advisable to
take note of the fact that the detection zone may be limited by non-
transparent objects (curtains, houseplants, cabinets, bookcases, etc.),
as well as glass and mesh partitions. There must be no windows, air
conditioners, space heaters or heating radiators in the Detector visibility
zone. The presence of furniture items on which an animal may climb
in the detection zone may cause a false alarm.
Recommended installation height – 2,3 m from the floor.
The Detector should be installed far enough from power supply
cables.
7 Detection Pattern
PASSIVE INFRARED DETEC-
TOR
WITH PET IMMUNITY
«PYRONE-5»
010 m
Side View
Top View
2,3 m
0
10 m
90о
Figure 2
Holes for the wall
installation
Holes for corner
installation
Cap screw place of
location
PCB clip
- fasten the base on the chosen place;
- install the PCB on its place;
- put on the cover.
Note – To exclude false alarms in the pet immunity mode,
the Detector should be installed vertically.
9 Connection
- Fulfill connections in accordance with designation on the PCB
(See Figure 3).
- Set up DIP-switches in accordance with application conditions
(DIP-switches assignment see on the PCB or in Cl.10 of this Instal-
lation Guide).
- Put on the Detector cover.

12 LED indication disabling
For the Detector operation masking the Detector provides LED
indication disabling mode. Switching to the mode is fulfilled by setting
up the DIP-switch «3» to «OFF» position.
13 Functional Testing
Before functional testing carrying out, close doors, windows, vents
and switch off forced air supply. Wait for 60 – 70 s after Detector
energizing. Determine the detection zone border by LED switching on.
Start walking across the detection zone at different distances from
the Detector (including maximal range). After 3-4 steps across the
detection zone, the Detector should display the detection by the LED
switching on. Wait till the LED is switched OFF and continue walking
across the detection zone. There must be no indication in absence of
moving objects in the room.
ATTENTION! The Detector must be checked at least annually in
order to test its performance
14 Storage and Transportation
The Detectors in their original packing may be shipped by any
transport means in covered vehicles (in railway, cars, trucks, sealed
heated compartments of aircraft, ship cargo holds, etc).
The storage room shall be free from current-conducting dust, acid
vapors, alkali and gases that cause corrosion and destroy insulation.
15 Manufacturer’s Guarantees
The Manufacturer guarantees conformity of the Detector to its
Technical Specifications if conditions of transportation, storage,
assembling and operation are observed. The guaranteed storage
period is 63 months since the date of manufacturing the Detector.
The guaranteed period of operation is 60 months since the date of
commissioning within the storage period guaranteed.
The Detectors that are found to non-conforming to their Technical
Requirements shall be repaired by the Manufacturer, provided that the
installation and operation rules have been complied with.
10 DIP-switches Setting
Table 3
DIP-switch
Pet immunity
up to
Note
«1» «2»
OFF OFF 10 kg Cats and fancy breed dogs
OFF ON 20 kg Cats and small
ON OFF 40 kg Long-hair dogs (Temperature contrast 6°С)
ON ON 40 kg Any dogs weighting up to 40 kg (Tempera-
ture contrast 8°С)
11 Indication
Table 4
Message LED indicator state
«Warm-up time» Lighting for 40 s after energizing
«Norm» Indication is OFF
«Alarm» Lighting for 3 s
Figure 3
AL
– 12V+
To control
panel (CP)
loops
Power supply
«RIELTA», JSC www.rielta.ru
Chapaeva Str. 17, Saint Petersburg 197101, Russian Federation,
E-mail: [email protected]
Tel/fax: [phone]
Rev. 5 of 07.04.2017
№Э00302
Made in Russia